SMC-50 Smart Motor Controller Quick Start

1 SMC-50 Smart Motor ControllerBulletin150 Quick StartOriginal InstructionsImportant user InformationRead this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be no event will Rockwell Automation, Inc.

2 Be responsible or liable for indirect or consequential damages resulting from the use or application of this examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc.

3 , is prohibitedThroughout this manual, when necessary, we use notes to make you aware of safety may also be on or inside the equipment to provide specific precautions. WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic : Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the information that is critical for successful application and understanding of the HAZARD: Labels may be on or inside the equipment, for example, a drive or Motor , to alert people that dangerous voltage may be HAZARD: Labels may be on or inside the equipment, for example, a drive or Motor , to alert people that surfaces may reach dangerous FLASH HAZARD.

4 Labels may be on or inside the equipment, for example, a Motor control center, to alert people to potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).Rockwell Automation Publication 150-QS003E-EN-P - April 20171 Table of ContentsImportant user Information .. 2 Table of ContentsPreface ..3 About This Publication.. 3 Additional Resources .. 3 Terminology.. 3 General Precautions.

5 4 Summary of Changes .. 5 Chapter 1 InstallationEnclosures .. 7 Mounting Requirements.. 8 Dimensions.. 9 Power Wiring.. 10 Power Lugs .. 11 Typical Power Diagrams .. 12 Control Wiring .. 13 Standard Control Terminal Block .. 13 Control Wiring Specifications .. 13 Typical Control Wiring Examples .. 15 Fan Wiring .. 17 Integrated Bypass Units .. 17 Solid-state Units.. 17 Upgraded Units .. 17 Option Modules .. 17 Bypass Operation and Diagrams .. 19 SMC-50 Controllers with Internal Bypass .. 19 SMC-50 Controllers with External Bypass.

6 19 Chapter 2 ProgrammingParameter Configuration .. 23 Parameter Configuration Using a 20-HIM-A6.. 23 Basic Parameter Access and Category/File Structure .. 24 Parameter Access .. 24 Category/File Structure .. 25 Quick Setup.. 27 Chapter 3 Operation and TroubleshootingOperation .. 29 Motor Configuration.. 29 Motor Tuning .. 29 Resistive Load Control .. 30 Troubleshooting with Diagnostic LEDs .. 31 Controller LED Status Indicator.. 31 Troubleshooting with Monitoring Equipment.. 31 Troubleshooting By Fault Code Abbreviated Listing.

7 312 Rockwell Automation Publication 150-QS003E-EN-P - April 2017 Table of ContentsAppendix ASCCR RatingsSCCR Ratings .. 35 Rockwell Automation Publication 150-QS003E-EN-P - April 20173 PrefaceAbout This PublicationThis Quick Start guide provides you with the basic information that is required to install, Start up, and program your SMC -50 Soft Starter. The SMC-50 soft starter is a reduced voltage soft starter that uses a state-of-the-art microprocessor- based control module. By using six back-to-back silicon-controlled rectifiers (SCRs) (two per phase), the SMC-50 soft starter provides controlled acceleration, operation/run, and deceleration of standard asynchronous induction motors.

8 Power structures are available with an integral bypass contactor or without (solid-state).The information that is provided in this Quick Start guide does not replace the user manual. The Quick Start guide assumes that the installer is a qualified person with previous experience and basic understanding of electrical terminology, configuration procedures, required equipment, and safety safety of maintenance personnel and others who might be exposed to electrical hazards associated with maintenance activities, follow all local safety-related work practices (such as NFPA 70E, Part II in the United States).

9 Maintenance personnel must be trained in the safety practices, procedures, and requirements that pertain to their respective job ResourcesThese documents contain additional information concerning related products from Rockwell can view or download publications To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales this publication, we also refer to the SMC-50 soft starter as the SMC-50 Controller . These terms are Controller user Manual, publication 150-UM011 Provides comprehensive user information for the SMC-50 Controller Selection guide , publication 150-SG010 Provides comprehensive selection information for SMC-50 Controller and 20-HIM-A6 and 20-HIM-C6S HIM (Human Interface Module)

10 , publication comprehensive user information for 20-HIM human interface Automation Wiring and Grounding Guidelines, publication general guidelines for installing a Rockwell Automation industrial Certifications website, declarations of conformity, certificates, and other certification Automation Publication 150-QS003E-EN-P - April 2017 PrefaceGeneral PrecautionsWARNING: Only personnel familiar with the Controller and associated machinery should plan or implement the installation, startup, and subsequent maintenance of the system.