SPECIAL NOTES - ITW BUILDEX

1 SPECIAL NOTESE ngineering NoteIn 1996, the anchors listed by UL were tested in plate steel that measured .188 and .118. Subsequent testing was done for z-purlin applications in May 1997 using (.037) or 20 gauge steel. Most recently in 2008, testing with the new Sammy X-Press was completed using (.030) or 22 gauge steel metal Nut DriversSpecial nut drivers were designed to be used with Sammys. When the appropriate nut drivers are used for installation, the driver spins free on the screw after installation is complete and eliminates the expected wrist snap, reduces over-torque, and prevents screw ScrewsDue to variations in hardness of certain metals, it should be noted that our self-drilling screws for steel will experience different drill speeds.

2 500-1500 RPM drill speed should be used. Metric ProductsMetric versions of the Sammy anchors are available at EnvironmentsFor attaching or anchoring in high vibratory environments, SPECIAL care should be taken not just for building attachments but also the hangers or assemblies being supported. Consult local code authorities for accepted anchoring Joist/TrussTruss manufacturers vary installation recommendations for composite joist. UL testing was completed to validate that Sammys and Sidewinders SWG 20 and SWG 25-380 can be installed into the top cord of a truss.

3 Sammy GST 20 can be installed into the center of the lower cord of a composite joist. Penetration of the upright center web is permitted by some joist manufacturers. Consult truss manufacturer for recommended installation point. Pre-drilling may be required by joist manufacturers. If so, pre-drill pilot hole 1/8 smaller than root diamter of fastener. Consult the table below:To increase efficiency of the installation process, sleeve tools, bit receivers, and wood bits are available for StandardsAll UL and FM testing complies with NFPA 13 and NEC standards.

4 Check with your local Authority Having Jurisdiction to confirm application and Listings / FM ApprovalsUL and FM reports are available at DrawingsCAD drawings are available and can be downloaded at in the Products Contact InformationTechnical Assistance: (800) BUILDEX Option #6 (x 3259)Customer Service: (800) BUILDEX Option #1 ModelRoot DiameterHole SizeGST GST SWG SWG Warranty Disclaimer of Warranty Proper fastener connection design takes into account where and how fasteners are used. Allowance for SPECIAL characteristics in materials, differences in materials, differences in types of materials being joined, unique or unusual environmental service or installation conditions and the safety factors required by anticipating normal or short term loading conditions must be considered.

5 Due to possible differences in specifications, applications, and interpretation of results, purchasers and specifiers must make their own evaluation of the products, to determine the suitability of these products for intended use. All warranties of BUILDEX products, expressed or implied, including the warranties of merchantabilty and fitness for particular purposes are specifically excluded except for the following: BUILDEX will repair or replace any product which, within twelve months after sale by BUILDEX or its distributors, is found by BUILDEX to be defective in material or workmanship - normal wear and tear accepted.

6 This is the sole warranty of BUILDEX and the sole remedy available to distributor or buyer. BUILDEX shall not be liable for any injury, loss or damage, direct, indirect, or consequential, arising out of the use of, or the inability to use, any BUILDEX find a distributor near you, call 800-BUILDEXS ammys for Wood .. 4 Sammys Swivel Head for Wood ..4 Sidewinders for Wood .. 5 Sammys for Steel .. 6 Sammy Swivel Head for Steel ..6 Sidewinders for Steel .. 7 Sammy X-Press , Swivel X-Press , and Sidewinder X-Press ..8 Sammy X-Press It Installation Tool.

7 8 Truss-T Hanger .. 9 Sammys for Concrete .. 10 Concrete/Wood Installation Kit .. 10 Sidewinders for Concrete ..11 Drywall Sammys /Toggle .. 12 Ceiling Screws ..12 Dektite Pipe Flashing ..12 Speedy Pole Tool .. 13 Sammy Saddle ..13 Spot Rite Level ..13 Assortment Pack .. 13 Approvals and Listings ..14-15 TABLE OF CONTENTSTABLE OF CONTENTS TABLE OF CONTENTS4 For the most up to date information, visit FlooringWood JoistDouble Sheetrock CeilingApprovalsRod SizePart NumberModelScrew DescriptionsUltimate Pullout (lbs)UL Test Load (lbs)FM Test Load (lbs)Box QtyCaseQty1/4"8002957 GST 1001/4 x 1"210 (7/16 OSB)670 (3/4 Ply)251251/4"8003957 GST 2001/4 x 2"1760 (Fir)251251/4"8004957 GST 3001/4 x 3"2060 (Fir)251253/8"8006957 GST.

8 751/4 x 3/4"564 (3/4" Ply)251253/8"8007957 GST 101/4 x 1"210 (7/16 OSB)670 (3/4 Ply)300251253/8"8008957 GST 201/4 x 2"1760 (Fir)8501475251253/8"8068925 GST 20-SS1/4 x 2"1760 (Fir)850251253/8"8009925 GST 25-3803/8 x 2-1/2"2113 (Fir)1500251253/8"8010957 GST 301/4 x 3"2060 (Fir)15001475251253/8"8069925 GST 30-SS1/4 x 3"2060 (Fir)251253/8"8011925 GST 401/4 x 4"2180 (Fir)251253/8"8012925 GST 601/4 x 6"2230 (Fir)251251/2"8013925 GST 21/4 x 2"1760 (Fir)251251/2"8014925 GST x 2-1/2"2113 (Fir)251251/2"8015925 GST 31/4 x 3"2275 (Fir)251251/2"8016925 GST 41/4 x 4"2180 (Fir)251251/2"8017925 GST 61/4 x 6"2230 (Fir)25125 Not less than2 nominal width (1-1/2 )Not less than 3 nominal thickness (2-1/2 ) (depth or side of vertical member)VERTICAL MOUNTWOOD WOOD WOOD WOOD WOODSAMMYS for WoodInstalls VERTICALLY into the bottom of wood structures easily and quickly!

9 #14 Black Nut DriverPart # 8113910 SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes intocontact with the material you are installing into, continue drilling until nut driver spins free. Installation is then complete. Warranty requires the use of the appropriate nut driver for installations.#14 SW Red Nut Driver Part # 8114910 Composite / TrussConsult truss manufacturer for recommended installation point.*Pre-drilling may be required for GST 25-380.

10 Tool available on page vertical use - install in center of lower 2 embedment into base material for NFPA 13 SizePart NumberModelScrew DescriptionsUltimate Pullout (lbs)UL Test Load (lbs)FM Test Load (lbs)Min ThicknessBox QtyCase Qty3/8"8139957SH-GST 201/4 x 2"1257 (Fir)10501475251251253/8"8141957SH-GST 301/4 x 3"1720 (Fir)1500147525125#14 Black Nut DriverPart # 8113910 SAMMY Swivel Head for WoodProduct Features No pre-drilling required. Quick to install using the Sammy Nut Driver with an 18V cordless drill/driver. Saves time from traditional methods.