SPECIFICATIONS - polypipe.com.au

1 SPECIFICATIONS FOR PLASSON COMPRESSION FITTINGS AND SADDLESMATERIALSC ompression Fittings, Tapping & Compression SaddlesBODYP olypropylene, high grade , high grade RINGA cetal (POM) CPVC rubber (NBR). EPDM and FRM O-rings available. (Approximately 70 Shore A.)REINFORCING RINGNUTS & BOLTS"TAPPER " SaddlesBODY/COMPRESSIONFITTINGP olypropyleneBOLT AND NUTS tainless steel to SS316 CUTTERB rass to BS 2874-CZ122O-RINGNBRSADDLE SEALEPDMSPLIT RINGP olyacetalOPERATING PRESSUREP lasson Compression FittingsComply with requirements of AS/NZS 4129. StandardsMark License No. 2018. Operating pressure at 20oC:PN16 (WATER) - 16mm to 125mm diameterSPECIFICATIONSS tainless steel on all female offtakes from " up to 4". All Tapping Saddles have stainless steelreinforced female steel (Stainless steel available). (Zinc plated with chromate passivator - yellow colour,shiny).

2 Page 1 of 3PN10 - 160mm diameterPlasson Tapping Saddles and Compression SaddlesComply with specification Tapping Bands of Australian Standard SAA MP52. See details in Price 4-22-02/WRC Standards PN or 16 depending on size refer pricelist. WSAA approved 98/46 Threaded FittingsSUITABLE PIPESP lasson Compression FittingsFor pipes 16mm to 160mm outside diameter. Metric OD systems for use with Polyethylene pipe manufactured to:AS1159 1988 Polyethylene Pipes for Pressure ApplicationsAS4130 PE Pipes for Pressure ApplicationsPE Pipes with outside dimensions to ISO OD series Rural FittingsFor Class Rural Polyethylene Pipe manufactured (ID Series) - Class 6 OPERATING TEMPERATUREThe compression saddles and valves are not for use with hot water although they withstand the same temperature as mostpolyethylene pipes.

3 The fittings and valves will withstand sub-zero female threads from to 4 have stainless steel reinforcing rings and are rated as above, except that 4 is suitable for PN Mpa for male fittings and Mpa for SS reinforced female fittings. Polypropylene Female outlets available with SSreinforcing. Female fittings and bushings 1/2" - 1" Mpa " 1 of 1300 661 417 SPECIFICATIONS FOR PLASSON COMPRESSION FITTINGS AND SADDLESFLANGESTHREADSCHEMICAL RESISTANCEA brief indicator of chemical resistance at 20oC follows:BenzeneФ Ф Brine Slaked Lime Compressed Air Cont. Oil Caustic Soda Ф Fuel Oil ФSPECIFICATIONSA cetal (1)CPVC (2)NBR (1)EPDM (2)FPM (3)PPPlasson Nut & BodyFlange dimensions in accordance with AS/NZS Drilled to suit PN16 flanges in accordance with Metal backingrings to be used with all flanges.

4 Internal parallel thread up to 2 . Internal taper thread 3 and up. External taper thread all sizes. All threads conform to ISO-7/1;BS21-1973; DIN2999; Nen3258; AS1722 Part 1 1975. Plasson polypropylene fittings are supplied, as standard, with Nitrile (NBR) rings and acetal split rings, which are suitable for watersupply and many chemical handling applications. For many chemicals however, NBR and acetal are unsuitable and Plasson sparerings of either EPDM or VITON (FPM) should be used to replace acetal. Generally nitrile is good in oily applications. O-RingsSplit RingsPage 2 of 3 Fuel Oil ФHydrochloric Acid Nitric Acid Dilute Carbolic Acid Lube Oils Phosporic AcidФ Sulphuric Acid Dilute Suitable Ф Medium Resistance Unsuitable(1) Supplied as standard component in Plasson fittings(2) & (3) Available as Plasson spare partsNBR O-Rings - CAT 7002 FPM O-Rings - CAT 7920 EPDM O-Rings - CAT 7910 CPVC Split Rings - CAT 7008 APPROVALSP lasson fittings have been tested and approved by major standard institutions such as WRC (GB), Staatliche MaterialprufungsanstaltDarmstadt (analogous to DIN8078 Part 1) (D); KIWA (NL); Standards Institution of Israel (IL); Australian Authorities (AUS); StatensProvningsansalt Stockholm (S); Statens Planmerk (S); SGWA (CH); Byggestyrelsen (DK);SKZ GmbH (analgous to DIN8076 Part 3-12/87)(D).

5 QAS Standards Australia StandardsMark although the most resistant is expensive EPDM is usually the economical solution. Generally, if EPDM or FPM O-Rings arerequired, then CPVC split rings should be used in place of standard acetal split rings. This is intended as a guide inchemicalapplicationsorpermanentlyburie dsituations may require stainless steel bolts and nuts. Inmany sizes the NBR ring can be replaced with EPDM or 2 of 1300 661 417 SPECIFICATIONS FOR PLASSON POLYPROPYLENE VALVESMATERIALSBODYP olypropylene, high grade , EPDM or FPM depending on (items 3067, 3039) Stainless PRESSURE AT 20oC - PN10 or see Price ListSPECIFICATIONS FOR PLASSON PVC VALVES MATERIALSPVCGASKETSPTFEO-RINGEDPMOPERATI NG PRESSURE AT 20oC -PN16 up to 63mm (2") diameterPN10 75mm ( ") diameterPIPE SUITABILITYP lasson Metric OD System for use with polyethylene pipe manufactured to:AS 1159 - 1988 Polyethylene Pipes for Pressure ApplicationsAS/NZS 4130 - 2002 PE Pipes for Pressure ApplicationsIn accordance with requirements for injection moulded PVC fittings withstanding PN 16 pressures in accordancewith UNI 3 of 3AS/NZS 4130 2002 PE Pipes for Pressure ApplicationsPlasson Rural ends.

6 AS TEMPERATUREP ermissible working pressures in accordance with DIN 8062 threads cylindricalMale threads - conicalIn accordance with ISO 7, UNI 339, DIN 2999, BS RESISTANCEPVC Valves - as for gaskets and O-Rings above. Refer chemical resistance for these 3 of 1300 661 417