Square Straight Steel Light Poles, Anchor Base

1 Engineered& ManufacturedIn TheUSARev. V09122018 This specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and specifications are subject to change without NameCatalog #Pole TypeProduct Overview Pole Shaft - The pole shaft is fabricated from hot rolled welded Steel tubing of one-piece construction with a minimum yield strength of 55 KSI. Pole Top - A removable top cap is provided for poles receiving drilling patterns for side-mount luminaire arm assemblies. Other pole top options include Tenon Top, Top Cap Only or Open Top which is typical when the pole top diameter matches the necessary slip-fit dimensions. Hand Hole - A reinforced hand hole with grounding provision is provided at 1 -6 from the base end of the pole assembly. Each hand hole includes a cover and cover attachment hardware. All pole assemblies are provided with a x 5 rectangular hand hole (dimensions are nominal).

2 Base Cover - A two-piece full base cover fabricated from ABS plastic is provided with each pole assembly. Additional base cover options, including a cast aluminum and fabricated Steel cover, are available upon request. Anchor Bolts - Anchor bolts conform to ASTM F1554 Grade 55 and are provided with two hex nuts and two flat washers. Bolts have an L bend on one end and are galvanized a minimum of 12 on the threaded end. Hardware - All structural fasteners are galvanized high strength carbon Steel . All non-structural fasteners are galvanized or zinc-plated carbon Steel or stainless Steel . Finish - Standard finishes are either Galvanized or Finish Painted. Additional finish options including Finish Paint over Galvanizing are available upon request. Design Criteria - Standard EPA (Effective Projected Area) and weight values are based on Standard Commercial Criteria (with gust factor) for side mounted fixtures only. Consult the factory on loading criteria for pole top mounted luminaires and/or brackets.

3 Satisfactory performance of Light poles is dependent upon the pole being properly attached to a supporting foundation of adequate Straight Steel Light Poles, Anchor Base206 W. McWilliams du Lac, WI specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and specifications are subject to change without ManufacturedIn TheUSARev. V09122018 Designation & Dimensional InformationEPA Load Information1. The total combined EPA and weight of all fixtures, brackets and attachments mounting to a Light pole cannot exceed the EPA and weight rating for a specified Standard EPA (Effective Projected Area) and weight values are based on Standard Commercial Criteria (with gust factor) for side mounted fixtures only. Consult the factory on loading criteria for pole top mounted luminaires and/or Satisfactory performance of Light poles is dependent upon the pole being properly attached to a supporting foundation of adequate : Additional sizes and configurations are available upon request.

4 "+" Indicates a vibration dampener is standardBASE MODEL80 MPH GUST90 MPH GUST100 MPH GUSTMAX EPA (SQFT)MAX WEIGHT (LBS)MAX EPA (SQFT)MAX WEIGHT (LBS)MAX EPA (SQFT)MAX WEIGHT (LBS) MODELPOLE DIMENSIONSBASE PLATEANCHOR BOLTSNOMINAL MOUNTING HEIGHTTOP SQ (IN)BASE SQ (IN)WALL THK (GA)STRUCTURE WEIGHT (LBS)BOLTCIRCLEDIA (IN)SQ (IN) x THICK (IN)DIA x LENGTH x HOOK (IN)PROJECTION (IN)VS-SSSA-10-4040-11-AB-FP10 -0 - x x x - -0 - x x x - -0 - x x x - -0 - x x x - -0 - x x x - -0 - x x x - -0 - x x x - -0 - x x x - -0 - x x x - 4VS-SSSA-20-5050-07-AB-FP20 -0 - x x x - 4VS-SSSA-25-4040-11-AB-FP25 -0 - x x x - -0 - x x x - -0 - x x x - 4VS-SSSA-25-5050-07-AB-FP25 -0 - x x x - 4VS-SSSA-30-4040-07-AB-FP30 -0 - x x x - -0 - x x x - 4VS-SSSA-30-5050-07-AB-FP30 -0 - x x x - 4VS-SSSA-30-6060-07-AB-FP30 -0 - x x x - -0 - x x x - 4VS-SSSA-35-6060-07-AB-FP35 -0 - x x x - -0 - x x x - W.

5 McWilliams du Lac, WI specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and specifications are subject to change without ManufacturedIn TheUSARev. V09122018206 W. McWilliams du Lac, WI specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and specifications are subject to change without InformationOptions & AccessoriesEngineered& ManufacturedIn TheUSARev. V09122018 Note: Please consult factory or your sales representative to verify options and accessories will work with your Light pole part number.* See previous pages for base model configurations. Consult factory or your sales rep for deviations from base models. Additional sizes and configurations available upon VS-SSSA-10-4040-11-AB-FP-DB-D1-EHHD esignationVS-SSSA= Square Straight Steel Anchor BaseLength*10 to 40 Base OD*40=4 50=5 60 =6 Top OD*40=4 50=5 60 =6 Finish TypeGV=Galvanzied Only (No Paint)FP=Finish PaintedFPGV =Finish Paint over GalvanizingThickness*07=7ga11=11gaPainte d ColorDB=Dark BronzeMB=Medium BronzeLG = Light GrayDG =Dark GreenHG =Hunter GreenSG =Slate GrayBK =BlackWH =WhiteSL =SilverSC=CustomFixture MountingDrill Mounting (includes cap)D1=SingleD2=2@180 @120 @90 @90 @90 MountingP1=4 OD x 5 Long TenonP2= OD x 4 Long TenonP3= OD x 6 Long TenonP4=4 OD x 6 Long TenonP5= OD x 4 Long TenonP6= OD x 5 Long TenonP7= OD x 5 Long TenonPQ= OD x 12 Long TenonPD=3 OD x 3 Long TenonP9=Custom Size TenonOther OptionsPC =Cap Only, No Side DrillingPL =Open Top, No Cap or Side DrillingDescriptionSPL=Special Cut Length (Please Specify)

6 BCSPCL=Special Base Plate to Match Existing Bolt Circle (May Add 2 Weeks to Production Lead Time, May Require Special Base Cover)VDA=Internal Vibration Dampener, Factory InstalledVDF=Internal Vibration Dampener, Field InstallableFBCS= Steel Full Base CoverFBCP=ABS Plastic Full Base CoverDescriptionULHH =UL Compliant Hand HoleNECHH=NEC Compliant Hand Hole & CoverEHH=Additional Hand Hole Opening w/ Cover Assembly(Specify Pole Height & Orientation)FST=Festoon Provision, Electrical by Others(Specify Pole Height & Orientation)CPL=NPT Pipe Coupling(Specify Pole Height, Orientation & NPT Size)PXDX=Side Drill + Tenon w/ Additional Hand Hole (Specify Tenon OD & Length)DescriptionSTAMP=Engineering Services, Signed & Sealed CalcsSTAMPCA=Engineering Services, CA Signed & Sealed CalcsPRE750=Pre-Ship Anchor Bolts - " x 17" x 3"PRE100=Pre-Ship Anchor Bolts - " x 36" x 4" Anchor BoltsAB=Includes Anchor BoltsLAB =Less Anchor Bolts206 W. McWilliams du Lac, WI