Standard Specification for Seamless Carbon Steel Pipe for ...

1 Designation: A 106/A 106M 06aUsed in USDOE-NE standardsStandard Specification forSeamless Carbon Steel Pipe for high -Temperature Service1 This Standard is issued under the fixed designation A 106/A 106M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last superscript epsilon (e) indicates an editorial change since the last revision or Standard has been approved for use by agencies of the Department of Scope* This specification2covers Seamless Carbon Steel pipe forhigh- temperature service (Note 1)inNPS1 8to NPS 48 [DN 6to DN 1200] (Note 2) inclusive, with nominal (average) wallthickness as given inASME B It shall be permissibleto furnish pipe having other dimensions provided such pipecomplies with all other requirements of this specification.

2 Pipeordered under this specification shall be suitable for bending,flanging, and similar forming operations, and for the Steel is to be welded, it is presupposed that a weldingprocedure suitable to the grade of Steel and intended use orservice will be It is suggested, consideration be given to possible The dimensionless designator NPS (nominal pipe size) [DN(diameter nominal)] has been substituted in this Standard for suchtraditional terms as nominal diameter, size, and nominal size. Supplementary requirements of an optional nature areprovided for Seamless pipe intended for use in applicationswhere a superior grade of pipe is required. These supplemen-tary requirements call for additional tests to be made and whendesired shall be so stated in the The values stated in either SI units or inch-pound unitsare to be regarded separately as Standard .

3 The values stated ineach system may not be exact equivalents. Therefore, eachsystem is to be used independently of the The following precautionary caveat pertains only to thetest method portion, Sections11,12, and13of this specifica-tion:This Standard does not purport to address all of the safetyconcerns, if any, associated with its use. It is the responsibilityof the user of this Standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prior to Referenced Standards:3A 530/A 530 MSpecification for General Requirements forSpecialized Carbon and Alloy Steel PipeE 213 Practice for Ultrasonic Examination of Metal Pipeand TubingE 309 Practice for Eddy-Current Examination of Steel Tu-bular Products Using Magnetic SaturationE 381 Method of Macroetch Testing Steel Bars, Billets,Blooms, and ForgingsE 570 Practice for Flux Leakage Examination of Ferromag-netic Steel Tubular Standard :ASME B and Seamless Wrought Standards.

4 MIL-STD-129 Marking for Shipment and Storage5 MIL-STD-163 Steel Mill Products, Preparation for Ship-ment and Standard :Fed. Std. No. 123 Marking for Shipments (Civil Agencies)5 Fed. Std. No. 183 Continuous Identification Marking of Ironand Steel Standards:SSPC-SP 6 Surface Preparation Specification No. 663. Ordering The inclusion of the following, as required will describethe desired material adequately, when ordered under Quantity (feet, metres, or number of lengths),1 This specification is under the jurisdiction of Committee A01 on Steel ,Stainless Steel and Related Alloys and is the direct responsibility of on Carbon Steel Tubular edition approved Oct. 1, 2006. Published October 2006. Originallyapproved in 1926.

5 Last previous edition in 2006 as A 106/A 106M ASME Boiler and Pressure Vessel Code applications see related Specifi-cations SA-106 in Section II of that referenced ASTM standards, visit the ASTM website, , orcontact ASTM Customer Service at ForAnnual Book of ASTMS tandardsvolume information, refer to the Standard s Document Summary page onthe ASTM from American Society of Mechanical Engineers (ASME), ASMEI nternational Headquarters, Three Park Ave., New York, NY from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA from Steel Structures Painting Council (SSPC), 40 24th St., 6thFloor, Pittsburgh, PA *A Summary of Changes section appears at the end of this ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.

6 Name of material ( Seamless Carbon Steel pipe), Grade (Table 1), Manufacture (hot-finished or cold-drawn), Size (NPS [DN] and weight class or schedule number,or both; outside diameter and nominal wall thickness; or insidediameter and nominal wall thickness), Special outside diameter tolerance pipe ( ), Inside diameter tolerance pipe, over 10 in. [250 mm]ID ( ), Length (specific or random, Section17), Optional requirements (Section9and S1 to S8), Test report required (Section on Certification ofSpecificationA 530/A 530M), Specification designation (A 106 or A 106M, includ-ing year-date), End use of material, Hydrostatic test in accordance with SpecificationA 530/A this specification, or NDE inaccordance with Section14of this Special The Steel shall be killed Steel , with the primary meltingprocess being open-hearth, basic-oxygen, or electric-furnace,possibly combined with separate degassing or refining.

7 Ifsecondary melting, using electroslag remelting or vacuum-arcremelting is subsequently employed, the heat shall be definedas all of the ingots remelted from a single primary Steel cast in ingots or strand cast is permissible. Whensteels of different grades are sequentially strand cast, identifi-cation of the resultant transition material is required. Theproducer shall remove the transition material by any estab-lished procedure that positively separates the For pipe NPS 11 2[DN 40] and under, it shall bepermissible to furnish hot finished or cold Unless otherwise specified, pipe NPS 2 [DN 50] andover shall be furnished hot finished. When agreed uponbetween the manufacturer and the purchaser, it is permissibleto furnish cold-drawn Heat Hot-finished pipe need not be heat treated.

8 Cold-drawnpipe shall be heat treated after the final cold draw pass at atemperature of 1200 F (650 C) or General Material furnished to this specification shall conform tothe applicable requirements of the current edition of Specifi-cationA 530/A 530 Munless otherwise provided Chemical The Steel shall conform to the requirements as tochemical composition prescribed inTable Heat An analysis of each heat of Steel shall be made by thesteel manufacturer to determine the percentages of the ele-ments specified in Section7. If the secondary melting pro-cesses employed, the heat analysis shall be obtainedfrom one remelted ingot or the product of one remelted ingotof each primary melt. The chemical composition thus deter-mined, or that determined from a product analysis made by themanufacturer, if the latter has not manufactured the Steel , shallbe reported to the purchaser or the purchaser s representative,and shall conform to the requirements specified in Product At the request of the purchaser, analyses of two pipesfrom each lot ( ) shall be made by the manufacturerfrom the finished pipe.

9 The results of these analyses shall bereported to the purchaser or the purchaser s representative andshall conform to the requirements specified in If the analysis of one of the tests specified conform to the requirements specified in Section7,analyses shall be made on additional pipes of double theoriginal number from the same lot, each of which shallconform to requirements Tensile The material shall conform to the requirements as totensile properties given inTable Bending For pipe NPS 2 [DN 50] and under, a sufficient lengthof pipe shall stand being bent cold through 90 around acylindrical mandrel, the diameter of which is twelve times theoutside diameter (as shown inASME B ) of the pipe,without developing cracks.

10 When ordered for close coiling, thepipe shall stand being bent cold through 180 around acylindrical mandrel, the diameter of which is eight times theoutside diameter (as shown inASME B ) of the pipe,without For pipe whose diameter exceeds 25 in. [635 mm] andwhose diameter to wall thickness ratio, where the diameter towall thickness ratio is the specified outside diameter divided bythe nominal wall thickness, is or less, the bend test shall beconducted. The bend test specimens shall be bent at roomtemperature through 180 with the inside diameter of the bendbeing 1in. [25 mm] without cracking on the outside portion ofthe bent : For 28 in. [711 mm] diameter in. [127 mm]thick pipe the diameter to wall thickness ratio = 28/5 = [711/127 = ].