Stealth Antennas - RSGB Shop

1 Stealth Antennas 12. by Steve Nichols, G0 KYA. 20. B. SG. Published by the Radio Society of Great Britain, 3 Abbey Court, Priory Business Park, Bedford MK44 3WH, UK. First published 2010. R. Radio Society of Great Britain, 2010. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the Radio Society of Great Britain.. Publisher's note The opinions expressed in this book are those of the author and not necessarily those of the RSGB. While the information presented is believed to be correct, the author, the publisher and their agents cannot accept responsibility for consequences arising from any inaccuracies or omissions.

2 I Contents 12. 1 Introduction 1. 2 Electrical and other safety issues 21. 20. 3 Using your roof space 29. 4 Stealth Antennas for the loft 37. 5 External Antennas 75. 6 Over-the-roof Stealth Antennas 81. 7 Examples of external Stealth Antennas 99. B. 8 Let's get really stealthy 123. 9 Commercial Stealth Antennas 139. SG. 10 Avoiding interference and EMC issues 161. 11 Maximising efficiency 177. Appendix 1 Glossary and abbreviations 184. Appendix 2 Other RSGB antenna books 197. R. Index 201.. 4. Stealth Antennas for the loft 12. THE SIMPLEST (and probably cheapest). antenna you can build is a loft-mounted half-wave dipole (Fig ). This is simply cut for your band of choice according to the chart and fed with 50 coax. 20. THE HALF-WAVE DIPOLE.

3 A half-wave dipole is cut to length Fig : The half-wave dipole is a simple antenna , but very effective. according to the formula: total length (in feet) = 468/f, where f is the centre frequency in MHz. The metric formula is total length (in metres) = Typical dipole lengths for the bands from 40m to 6m are given in Table B. When I was first licensed I strung up a half-wave dipole for 10m in my attic. It worked a treat with a very low SWR across most of the band. What's more it worked stations with many contacts being made across Europe and the USA. Just about any type of insulated wire will work and you don't need end SG. insulators just use a staple gun to tack the wire to the wooden rafters and let the final four inches or so dangle free away from the wood.

4 This is a safety feature and prevents the antenna arcing to the woodwork, although that is very unlikely to happen if you keep the power levels down. I usually leave my power setting at about 25W and seldom use more than 50W. Do not use a linear amplifier! A so-called chocolate block' electrical connector will let you connect the ends of the dipole to R. your 50 coax, which Frequency (MHz) Total length (ft in) (metres). can then be led 65ft 11in vertically away at 46ft 4in right angles to the 33ft dipole to prevent RF.. 25ft 10in pick-up and help keep 22ft 1in the antenna balanced. 18ft 9in If possible use a balun 16ft 5in or choke as described 15ft 10in earlier. 9ft 4in Once you have installed the antenna Table : Half-wave dipole lengths.

5 37. Stealth Antennas check the SWR in the centre of the band. Now check it at the band edges too. If the SWR is better at the lower edge of the band than the top end this means it is too long. If it is better at the top end of the band it is too short. If it is too long don't cut it just fold the ends back on themselves and either twist the wires together or use nylon cable clips. Electrically it will appear shorter' to your radio and have the same effect as cutting it. Don't be surprised to find that you have to shorten the antenna slightly once you have it in position. The PVC covering of the wire and capacitative end 12. effects will make it appear too long electrically and it is easier to shorten an antenna than lengthen it. One you have the lowest SWR at or around the centre of the band, stop as long as it is less than about 2:1 you will be fine.

6 In reality you should be able to get it to :1 or better. You may struggle to get the 30m and 40m versions in your loft they may 20. be too long. If that is the case see the section on the zig-zag dipole later on. Just about all of the others should fit within an average-sized loft. It is best to mount the centre of the antenna as high as you can in the apex of the roof. This helps keep it away from electrical wiring and copper water tanks that might otherwise affect its tuning. It also helps with your radiated signal as it is the current portion of the antenna that does all the work and the current maximum on a half wave dipole is in the centre. The dipole legs can either be tacked along the central apex with a staple gun B. or brought down in an inverted-V configuration - see next section.

7 A half-wave dipole is strictly speaking a monoband antenna , although a 40m (7 MHz) version can be used on 21 MHz (15m) albeit with a slightly higher SG. SWR. You can use a dipole on something other than its design frequency, but you will need to use an ATU and the performance will not be very good. But as a get you going' compromise it will work. As explained in our later chapter on matched and unmatched losses using a long run of coax with a high SWR will result in high losses and is not recommended. If you really want to use a single dipole in the loft on a band other than that of its design frequency you are better off feeding it with 300 or 450 ribbon cable, but this is less easy to handle than coax and must be kept away from R. metallic objects.

8 your dipole then becomes a doublet. If you do want to experiment with this, cut your dipole for the lowest frequency you want to use and then use it with open wire feeder on this and higher frequencies. There are other coax-fed multi-band alternative that you can read about later.. THE INVERTED-V. The dipole doesn't have to be laid out in a straight line. You can, in fact, arrange one as an inverted-V with the centre at the apex of your roof and the legs coming down at an angle. In fact, there are a number of advantages in doing this. The first is that an inverted-V loses some of its directional 38. 4. Stealth Antennas for the loft characteristics. A dipole usually has its maximum radiation at right angles to the wire with little radiation off its ends, but when arranged as an inverted-V it becomes slightly more omnidirectional, as shown in Fig You will find that as an inverted-V a dipole will need to be up to about 4% shorter than if it is in a straight line.

9 Don't worry about this. Cut it according to the chart and fold it back once installed to bring it to as close to a 1:1 SWR as you can. 12. Secondly, the impedance of a half wave dipole in free space is more like 70 - 75 , not the 50 our radio expects. This can result in an SWR of about :1 :1. By narrowing the angle Fig (a): You can see that between the legs the impedance changes and the SWR is reduced when erected in a straight to closer to 1:1. line the dipole is quite directional. But, and it is a big but, the angle between the legs of a dipole 20. should not fall below about 70 - 80 . For best results with this type of antenna , the apex angle should be kept between 90 and 110 . Less than this and the radiators start to become parallel to each other and signal cancelling will start to occur.

10 Above about 120 the antenna starts looking like a standard dipole, minimising any of the feed impedance and shortening effects. The optimum apex angle is 90 - 120 , but it isn't that critical. Some pitched roofs are actually very steep and you should B. check to see what the angle is on yours. If you wish to fit an inverted-V you might be better off putting each leg across the side of the roof rafters to reduce the angle. That is, install it an SG. Fig (b): But when erected angle with the rafters. as an inverted-V you gain a Inverted-V dipoles for several different bands can be couple of S-points (10 - 12dB). connected to the same feeder, as shown in Fig to provide a in the directions in which the multi-band antenna . dipole wires point.