ARCH 331 Note Set Su2012abn 1 Structural load Requirements International Building code (2012) ARCH 331 Note Set Su2012abn 2 Live Loads & Allowed Reductions ARCH 331 Note Set Su2012abn 3 Minimum Roof Loads ARCH 331 Note Set Su2012abn 4 Minimum Snow Loads ARCH 331 Note Set Su2012abn 5 Documentation of Loads
The ground snow load, P , shall be indicated. In areas where the ground snow load, P , exceeds 10 pounds per square foot (psf) (0.479 kN/m2), the following additional information shall also be pro- vided, regardless of whether snow loads govern the design of the roof: l. Flat-roof snow load, P 2. Snow exposure factor, Ce. 3. Snow load ...
Domain:
Source:
Link to this page:
1 ARCH 331 Note Set Su2012abn 1 Structural load Requirements International Building code (2012) ARCH 331 Note Set Su2012abn 2 Live Loads & Allowed Reductions ARCH 331 Note Set Su2012abn 3 Minimum Roof Loads ARCH 331 Note Set Su2012abn 4 Minimum Snow Loads ARCH 331 Note Set Su2012abn 5 Documentation of Loads
Mechanics of Materials MECHANICS MATERIALS Mechanics of Materials 3 Lecture 5 Foundations Structures ARCH 331 F2008abn Mechanics of Materials external loads and their effect on deformable bodies use it to answer question if structure meets requirements of ± stability and equilibrium
ARCH 631 Note Set 10.1 F2013abn 3 Reinforced concrete is a composite material, and the average density is considered to be 150 lb/ft3. It has the properties that it will creep (deformation with long term load) and shrink (a result of
The nominal flexural strength Mn is the lowest value obtained according to the limit states of 1. yielding 2. lateral-torsional buckling 3. flange local buckling 4. web local buckling For a laterally braced compact section (one for which the plastic moment can be reached before local buckling) only the limit state of yielding is applicable.
1 Mechanics of Materials 1 S2009abn Lecture 4 Elements of Architectural Structures ARCH 614 E LEMENTS OF A RCHITECTURAL S TRUCTURES: F ORM, B EHAVIOR, AND D ESIGN ARCH 614 D R. A NNE N ICHOLS S PRING 2014 four mechanics of materials lecture www.carttalk.com
ARCH 331 Note Set 22.1 Su2014abn 5 Reinforced Concrete Beam Members Strength Design for Beams Sstrength design method is similar to LRFD. There is a nominal strength that is reduced by a factor which must exceed the factored design stress.
ARCH 331 Note Set 28.1 Su2014abn 2 Reinforced Masonry Design Structural design standards for reinforced masonry are established by the Masonry Standards Joint Committee consisting of ACI, ASCE and The Masonry Society (TMS), and presents allowable stress design as well as limit state (strength) design.
Connections Connections must be able to transfer any axial force, shear, or moment from member to member or from beam to column. Steel construction accomplishes this with bolt and welds. Wood construction uses nails, bolts, shear plates, and split-ring connectors. Single Shear - forces cause only one shear “drop” across the bolt.
ENDS 231 Symbols F2007abn 2 d depth, often cross-sectional (in, mm, m); perpendicular distance from a force to a point in a moment calculation (in, mm, m) dx difference in the x direction between an area centroid ( x) and the centroid of the composite shape (xˆ ) (in, mm) dy difference in the y direction between an area centroid ( y) and the centroid of the composite
Pure Bending in Beams With bending moments along the axis of the member only, a beam is said to be in pure bending. Normal stresses due to bending can be found for homogeneous materials having a plane of symmetry in the y axis that follow Hooke’s law. Maximum Moment and Stress Distribution
Beam Bending Stresses and Shear Stress Notation: A = name for area A web = area of the web of a wide flange section b = width of a rectangle = total width of material at a horizontal section c = largest distance from the neutral axis to the top or bottom edge of a beam d = calculus symbol for differentiation = depth of a wide flange section d y
wind, snow, and earthquake loads. Load factor — a factor specified in this Standard for structural design to be used with loads (or actions) in deriving design loads (or actions). Load (action) — magnitude of loads. Strength limit state — a limit state of collapse or loss
No-Load Speed Rotational speed, at no load... /min per Minute Revolutions per minute WARNING: To ensure safety and reliability, all repairs should be performed by a qualified service technician. SAFE OPERATION PRACTICES FOR WALK-BEHIND SNOW BLOWER DANGER: This snow blower is capable of amputating hands and feet and throwing objects.
valve (1) remaining almost closed to the full load (the maximum output) with the throttle valve fully opened. In order to meet the requirements for the proper mixture ratio under these varying conditions, a low-speed fuel system (the pilot system) and a main fuel system (the main system) are provided in Mikuni VM-typecarburetors.-1-