Example: barber

SUGGESTED TAPPING SPEEDS ANGULAR - Balax | Forming …

TECHNICAL INFO74 TECHNICAL INFOmATERIALSFmTAPPING RPm#0 #1 #2 m2#3 #4#5 m3#6 #8 m4#10 m5#121/4 m65/16 m83/8 m107/16 m111/2 m125/8 m163/4 m181" m24 Low CARbon steeL55350328792444212318771682152312821 106973841674561481420336280210 MeDiuM CARbon steeL35222918321555135111941070969816704 619535429357306268214178134 HigH CARbon steeL10637524444386341306277233201177153 1221028776615138 CAst steeL25159213091111965853764692583503442 38230625521919115312796300 seRies stAinLess steeL20127410478897726826115544664023543 0624520417515312210276400 seRies stAinLess steeL15955785667579512459415350302265229 184153131115927657gRey CAst iRon704459366531112702238921401939163114 0812381070857713612535428357268 DuCtiLe CAst iRon503185261822221930170615291385116510 06885764612510437382306255191 ALLoy CAst iRon402548209417781544136512231108932805 708611490408350306245204153 ALuMinuM CAst ALLoys6038223141266623162047183416621398 12071062917735611525459367

TECHNICAL INFO 74 TECHNICAL INFO mATERIAL SFm TAPPING RPm #0 m1.6 #1 #2 m2 #3 m2.5 #4 #5 m3 #6 m3.5 #8 m4 #10 m5 #12 1/4 m6 5/16 m8 3/8 m10 7/16 m11 1/2 m12 5/8

Tags:

  Speed, Forming, Suggested, Tapping, Angular, Suggested tapping speeds angular

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of SUGGESTED TAPPING SPEEDS ANGULAR - Balax | Forming …

1 TECHNICAL INFO74 TECHNICAL INFOmATERIALSFmTAPPING RPm#0 #1 #2 m2#3 #4#5 m3#6 #8 m4#10 m5#121/4 m65/16 m83/8 m107/16 m111/2 m125/8 m163/4 m181" m24 Low CARbon steeL55350328792444212318771682152312821 106973841674561481420336280210 MeDiuM CARbon steeL35222918321555135111941070969816704 619535429357306268214178134 HigH CARbon steeL10637524444386341306277233201177153 1221028776615138 CAst steeL25159213091111965853764692583503442 38230625521919115312796300 seRies stAinLess steeL20127410478897726826115544664023543 0624520417515312210276400 seRies stAinLess steeL15955785667579512459415350302265229 184153131115927657gRey CAst iRon704459366531112702238921401939163114 0812381070857713612535428357268 DuCtiLe CAst iRon503185261822221930170615291385116510 06885764612510437382306255191 ALLoy CAst iRon402548209417781544136512231108932805 708611490408350306245204153 ALuMinuM CAst ALLoys6038223141266623162047183416621398 12071062917735611525459367306229 ALuMinuM DieCAst ALLoys7044593665311127022389214019391631 140812381070857713612535428357268 ALuMinuM wRougHt ALLoys8050964188355530882730244622151864 160914151223980815700611489408306zinC DieCAstings80509641883555308827302446221 51864160914151223980815700611489408306

2 CoPPeR6038223141266623162047183416621398 12071062917735611525459367306229bRAss, fRee MACH ining60382231412666231620471834166213981 2071062917735611525459367306229 CAst bRonze5031852618222219301706152913851165 1006885764612510437382306255191niCkeL ALLoys1063752444438634130627723320117715 31221028776615138titAniuM ALLoys1063752444438634130627723320117715 31221028776615138 PLAstiC, tHeRMosetting402548209417781544136512231 108932805708611490408350306245204153 PLAstiC, tHeRMoPLAstiC805096418835553088273024462 2151864160914151223980815700611489408306 1. SPEEDS are starting points for cold Forming taps or for cutting taps in thru hole Fine pitch cold Forming taps less than 1/2" diameter may be run faster in soft material with good lubrication.

3 Increase TAPPING RPM gradually until tap heat buildup due to lubrication failure begins to For cutting taps in blind holes, reduce RPM by 25% to 50%.4. Tap Feed Rate = Tap RPM x Tap Pitch (Displacement/Revolution)Example: 1/4-28 Tap @ 1000 RPM Feed Rate = 1000 Rev/Min. x 1/28 Inch/Rev)= in/Min Example: M6 x Tap @ 1000 RPM Feed Rate = 1000 Rev/Min. x mm/Rev )= 1000 mm/MinSUGGESTED TAPPING SPEEDS faSt delivery on Standard coolant-thru tapSUsing Balax s EDM process, almost any standard Thredshaver or Thredfloer tap can be modified into the coolant-thru tap style of your choice: thru-coolant, radial coolant, or ANGULAR coolant.

4 It s economical and turn-around time is TAPSTHRU - COOLANT RADIAL - COOLANTANGULAR - COOLANTTHRU - COOLANT RADIAL - COOLANTANGULAR - COOLANTTHRU - COOLANT RADIAL - COOLANTANGULAR - COOLANTTHRU - COOLANT RADIAL - COOLANTANGULAR - COOLANTTHRU - COOLANT RADIAL - COOLANTANGULAR - COOLANTS pecial coolant-thru tapS for cuStoM applicationSFor processes requiring an engineered special coolant-thru tap, custom tap blanks are made with coolant-thru holes in the style best suited for the TAPPING application.


Related search queries