Supersedes September 2012 HEZ breakaway and non …

1 Technical Data 2130 Effective January 2016 Supersedes September 2012 BUSSMANNSERIESHEZ breakaway and non- breakaway in-line rejection fuse holders for UL Class CC fusesCatalog Symbol: HEZD escription:Bussmann series HEZ submersible, single-pole in-line rejection fuse holders are for UL Class CC fuses. They are available in non- breakaway and breakaway versions with an array of terminal options to meet application needs. breakaway versions come with insulating boots to provide submersibility per UL IP67. Non- breakaway versions require ordering optional insulating boots for fuses:Catalog symbolOperationData sheet :Volts: 600 VAmps: up to 30A limited by conductor sizeWithstand: 200kA RMS information:UL Listed, Guide IZLT, File E14853 CSA Certified, Class 6225-01, File 47235CE, RoHS compliantCoupling nut torque:10-20 Lb-In ( N m)Operating and storage temperature:-40 F (-40 C) to 221 F (105 C)Insulating boots:Two insulating boots come standard with the breakaway holder configurations.

2 Insulating boots are not included as standard with non- breakaway holders. Two insulating boots must be ordered separately, if required, for each non- breakaway holder ordered. When insulating boots are utilized, extra heat retention requires that fuses are sized at a minimum of 200% of the RMS load instructions:Strip wire insulation equal to the depth of the crimp or screw terminal. Torque screw terminal to 35 Lb-In ( N m) or crimp terminal twice, spacing crimps a distance of one-third from each end (as shown below) using an appropriate crimp tool and die.

3 See page 3 for recommended crimping products:Catalog sheet supplemental in-line fuse holder2126 HEBOne-pole supplemental in-line fuse holder2127 HEYTwo-pole Class CC in-line fuse holder2126 HETOne-pole in-line, permanently installed neutral2125 NNB-RClass CC neutral dummy link (not a fuse) Strip wire insulation to depth of terminalCrimp terminal twiceat locations 1/3 distancefrom each endUse these part numbers to order insulating boots for a non- breakaway HEZ holder:DescriptionPart conductor2A0660 Dual conductor2A0661 Boot (104) (119) ( 33) ( 20)2 Technical Data 2130 Effective January 2016 Bussmann series HEZ breakaway and non- breakaway in-line rejection fuse holders for UL Class CC fusesNon- breakaway catalog number systemHEZ - A ACatalog symbolLoadside terminalLineside terminalAgency InformationLoadside terminalLineside terminalReference length ABreakaway equivalentULCSAT erminal typeWire range*Terminal typeWire range*HEZAAXXCu crimp#8-16; (2) #12-16Cu crimp#8-16.

4 (2) # (112)HEZ-AW-RLC-A * Solid/stranded conductors unless otherwise dimensions - in (mm) (232) Assembled lengthNon- breakaway terminal dataTerminal typeConductor dataCatalog symbol [Load /Line]SizeNo. per terminalSolidStrandedCu crimp#8-16#10-1612 order:Specify catalog symbol HEZ and the loadside terminal code. Then select a lineside terminal code that is available with the loadside terminal. Example: HEZ-AA defines a non- breakaway holder with both loadside and lineside copper crimp terminals for a single 8-16 AWG or two 12-16 AWG Data 2130 Effective January 2016 Bussmann series HEZ breakaway and non- breakaway in-line rejection fuse holders for UL Class CC catalog number systemHEZ - A W - RYCC atalog symbolLoadside terminalLineside terminalAgency InformationLoadside terminalLineside terminalLength A (reference)

5 Non- breakaway equivalentULCSAT erminal typeWire range*Terminal typeWire range*HEZARLC-AXXCu crimp#8-16; (2) #12-16Cu crimp#8-16; (2) # (147)HEZ-AARYCX Cu crimp#8-16; (2) #12-16Cu dual setscrew#2-12 (159) * Solid/stranded conductors unless otherwise - in (mm) (263)Assembled lengthBreakawayTo order:Specify catalog symbol HEZ and the loadside terminal code plus the letter W. Then select a lineside terminal code that is available with the loadside terminal. Example: HEZ-AW-RCL-A defines a breakaway holder with both lineside and loadside copper crimp terminals for a single 8-16 AWG or two 12-16- AWG lineside terminal dataTerminal type Conductor dataCatalog symbolSizeNo.

6 Per terminalSolidStrandedCu crimp#8-16#12-1612 -RLC-ACu dual setscrew#2-122 -RYC Not dual wire rated. One wire per loadside terminal dataTerminal typeConductor dataCatalog symbol [Load /Line (2) & (3)]SizeNo. per terminalSolidStrandedCu crimp#8-16#10-1612 ARecommended crimping tools:Some of the commercially available crimping tools that can be used with the HEZ fuse holders are listed in the table below. This list is not intended to exclude the use of other crimping tools that can provide similar crimps or terminalT and B P/N (Die)AWT-111M (Die C)Sta-Kon ERG4002 (Die C)Bussmann series HEZ breakaway and non- breakaway in-line rejection fuse holders for UL Class CC fusesTechnical Data 2130 Effective January 2016 Eaton1000 Eaton BoulevardCleveland, OH Division114 Old State RoadEllisville, MO 63021 United 2016 EatonAll Rights ReservedPrinted in USAP ublication No.

7 2130 - BU-MC16001 January 2016 Eaton and Bussmann are valuable trademarks of Eaton in the US and other countries. You are not permitted to use the Eaton trademarks without prior written consent of is a registered trademark of the Canadian Standards is a registered trademark of the Underwriters Laboratories, only controlled copy of this data sheet is the electronic read-only version located on the Eaton network drive. All other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications.

8 Eaton reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. Eaton also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible us on social media to get the latest product and support Eaton s Bussmann series product information, call 1-855-287-7626 or