SURFACE PREPARATION - techstone.ca

1 DATA SHEETAn attractive anti-slip surfacein minutes!Up to a for Anti-Slip Traction (50% higher than the safety standard)! Porches & Steps Pool Decks & Patios Balconies Garage & Utility Floors Walkways Foundation Walls Basements Laundry AreasAND ANTI-SLIP FLOOR COATINGET ENDUIT ANTI-D RAPAGE POUR PLANCHERDESCRIPTION:Pre-mixed, non-cementitious, low VOC, non-toxic, water-based polymer/stone coating for interior/exterior floor and wall surfaces . USES:Designed for use as the bonding primer portion of the Beauti-Tone HardRock , FlexRock Floor and Granite Spreadable Stone coating SLIP-RESISTANT FLOORINGB eauti-Tone Textured Primer can also be used as a simple slip-resistant floor finish or masonry paint.

2 Roll on two coats (tinted to desired colour) - at least two hours between coats. Allow 24 hours to cure (longer in damp or cool conditions) and then seal with HardRock High-Build Clear Coat or Beauti-Tone Epoxy Clear Coat (indoors) for durability, water repellency and chemical :Beauti-Tone Textured Primer is available in: 946 ml, litre and litre Textured Primer penetrates and locks firmly onto concrete and more to create an ideal bonding base for any of the Beauti-Tone Spreadable Stone decorative coatings. It s also an excellent slip-resistant finish that transforms all kinds of slippery floors into colourful, high-traction surfaces . It can be used indoors and out -- and can be tinted to many appealing colours.

3 If you are using it as part of a HardRock , FlexRock or Granite finish, just roll on one good coat and proceed as BENEFITS: Easy roller or brush application Adds colour and light decorative texture to drab concrete surfaces Pre-mixed and ready to apply economical stand-alone coating numerous store-tinted colours. excellent adhesion Very high abrasion and impact resistance Water-based, user friendly and environmentally safe with very low VOCsSURFACE PREPARATIONFor optimum long term performance, surfaces must be clean and dry and free from dust, dirt, spalling, efflorescence, oil, poorly bonded or glossy paint, glue, SURFACE sealers and other contaminates. (see detailed installation guide for more information).

4 CONCRETE1) SURFACE should be level and in good condition. Chip away any loose or flaking concrete and skim coat any rough or uneven areas with a quality masonry repair product (following manufacturer s instructions). 2) Power wash concrete thoroughly. (For best results, especially for exterior surfaces , a minimum of 1500 psi is VERY STRONGLY RECOMMENDED in a slow sweeping motion. Hold spray tip 3 - 4 above the SURFACE to effectively clean out concrete pores for best bond.) Otherwise, scrub SURFACE with a strong solution of Natura Safe Prep or TSP and rinse thoroughly. 3) If concrete is very smooth, new or efflorescent, etch the SURFACE with a Natura Safe Etch (at least twice) or with 2-parts water / one part muriatic acid solution (one or two times) prior to general cleaning.

5 If concrete is heavily soiled, a brief cleaning may need to be performed prior to etching to ensure effective etching. 4) New concrete minimum 28 day cure before application. 5) New masonry at least 48 hours cure. (see detailed installation guide for more information).APPLICATIONA pply to clean, stable SURFACE in ambient temperature above 10 C using standard painting practices with a 15 mm roller or brush. Avoid heavy loop texture, working primer until a light sand texture is achieved. Dry to touch in 1-2 hours, longer in cool damp conditions. If taping grout effects, allow primer to reach full cure and bond strength for 24 hours before additional TImE:Dry to touch in 60 minutes, depending on atmospheric conditions.

6 Protect coated surfaces for 6-8 hours prior to exposure to rain or heavy condensation. In dry, warmer conditions product cure is complete in 24 hours. In cooler weather (5 - 10 C) allow at least 48 hours for :Varies with substrate conditions and application method/thickness. Typical coverage: 160 - 200 per UP:Equipment can be cleaned with soap and water prior to cure of material. SEALING:When fully cured, Textured Primer can be sealed with the recommended Beauti-Tone Sealer for your specific ) Interior/Exterior Projects Beauti-Tone HardRock High-Build Clear Coat (1817-948/957) is used for easier cleanability, durability and ) Interior/Exterior Heavy Duty Performance For higher traffic residential floors, garage floors, commercial floors and other more demanding applications requiring the highest level of durability, cleanability and chemical resistance, Beauti-Tone HARDROCK High-Build Clear Coat (1817-984/993) is recommended.

7 Perform re-coats every two years if in original, unopened, undamaged container for up to two years. Use open container within six months. Protect contents from contact with eyes and skin, flood eyes repeatedly with potable water for 15 minutes. DO NOT RUB EYES due to course nature of material. Wash hands thoroughly after handling. Do not take internally. KEEP OUT OF REACH OF CHILDREN. Keep container closed. Dispose of old material as prescribed by local laws.