TDK- Lambda HWS5 0 A

1 TDK-LambdaHWS50 ASPECIFICATIONSA257-01-01 MODEL ITEMS1 Nominal Output VoltageV2 Maximum Output CurrentA3 Maximum Output PowerW4 Efficiency (Typ.) (*1)100 VAC%200 VAC%5 Input Voltage Range(*2)-85 - 265 VAC (47 - 63Hz) or 120 - 370 VDC 6 Input Current (Typ.) (*1) Inrush Current (Typ.)(*1)(*3)-14A at 100 VAC, 28A at 200 VAC, Ta=25 C, Cold Start8 PFHC-Designed to meet IEC61000-3-2 9 Power Factor (Typ.) (*1)-10 Output Voltage Range - - - - Maximum Ripple & Noise 0<Ta<70 CmV120120150200(*4)-10<Ta<0 CmV16016018024012 Maximum Line Regulation (*5)mV20209619213 Maximum Load Regulation (*6)mV404015024014 Temperature Coefficient-Less than / C15 Over Current Protection (*7)A16 Over Voltage Protection (*8) - - - - - Hold-up Time (Typ.)

2 (*1)-20ms18 Leakage Current(*9)-Less than (Typ) at 100 VAC / (Typ) at 230 VAC19 Remote Sensing--20 Parallel Operation --21 Series Operation-Possible22 Operating Temperature (*10)--10 to +70 C (-10 to +50 C:100%, +60 C:70%, +70 C:40%)23 Operating Humidity- 30 to 90%RH (No Condensing) 24 Storage Temperature--30 to +85 C25 Storage Humidity- 10 to 95%RH (No Condensing)26 Cooling-Convection Cooling27 Withstand Voltage Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA) Output - FG : 500 VAC (20mA) for 1min28 Isolation Resistance-More than 100M at 25 C and 70%RH Output - FG.

3 500 VDC29 VibrationAt no operating, 10 - 55Hz (Sweep for 1min) Constant, X,Y,Z 1hour Shock-Less than SafetyApproved by UL60950-1, CSA60950-1, to meet Den-an Appendix 8 at 100 VAC Line DIPD esigned to meet SEMI-F47 (200 VAC Line only)33 Conducted Emission(*11)-Designed to meet EN55011/EN55022-B, FCC-B, VCCI-B34 Radiated Emission(*11)-Designed to meet EN55011/EN55022-B, FCC-B, VCCI-B35 Immunity(*11)-Designed to meet IEC61000-6-2 IEC61000-4-2, -3, -4, -5, -6, -8, -1136 Weight (Typ.)-260g37 Size (W x H x D) x 82 x 120 ( Refer to Outline Drawing ) *Read instruction manual carefully, before using the power supply unit.

4 =NOTES=* 100 VAC/200 VAC, Ta=25 C, nominal output voltage and maximum output power.* cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - 240 VAC(50 - 60Hz).* applicable for the inrush current to Noise Filter for less than * with JEITA RC-9131B probe, Bandwidth of scope :100 MHz.* - 265 VAC, constant load.* load-Full load, constant input voltage. * with automatic recovery. Avoid to operate at over load or short circuit condition.* circuit will shut down output, manual reset (Re power on).

5 * by the each measuring method of UL, CSA, EN and Den-an (at 60Hz), Ta=25 C. * Derating - Derating at standard mounting. Refer to OUTPUT DERATING CURVE (A257-01-02_ ). - Load (%) is percent of maximum output power or maximum output current, do not exceed its derating of maximum load.* power supply is considered a component which will be installed into a final final equipment should be re-evaluated that it meets EMC < < - - - < < < <85 TDK-LambdaHWS50 AOUTPUT DERATINGA257-01-02-10 - +4560706558704030301001005010010086Ta ( C)LOAD (%)MOUNTING AMOUNTING B, DMOUNTING C100020406080100120-1001020304050607080 LOAD (%)Ta ( C)OUTPUT DERATING CURVEMOUNTING AMOUNTING B, DMOUNTING CMOUNTING A(STANDARD MOUNTING)MOUNTING BMOUNTING CMOUNTING DDON'T USE