Technical Data Sheet - Jotun

1 ^(ValidationDate)15311531;3560;15331,2po lyurethaneTechnical data SheetHardtop FlexiProduct descriptionThis is a two component chemically curing aliphatic acrylic polyurethane coating. It has a glossy finish with very good gloss retention. It is a high solids, high build product. It is fast drying. It can be used direct to metal. The coating is highly flexible, impact resistant and has excellent adhesion. To be used as topcoat in atmospheric and certificatesGrain, Newcastle Occupational HealthFood, Compliant with USA, FDA Title 21, Part for dry solidsWhen used as part of an approved scheme, this material has the following certification:- Low Flame Spread in accordance with EU Directive for Marine Equipment.

2 Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8 Consult your Jotun representative for to colour card and Multicolor Industry tinting system (MCI)Typical useOther variants availableHardtop Flexi AluMarine:Recommended for topside, container deck and :Recommended for offshore environments, refineries, power plants, bridges and buildings. Suitable for a wide range of industrial to separate TDS for each certificates and approvals may be available on dataPropertyTest/StandardDescriptionSoli ds by volumeGloss level (GU 60 )ISO 2813 VOC-US/Hong KongUS EPA method 24 (tested)(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)VOC-EUIED (2010/75/EU) (theoretical)64 Flash pointISO 3679 Method 125 Cgloss (70-85)344 g/l353 3233 VOC-ChinaGB/T 23985-2009 (tested)317 g/lVOC-KoreaKorea Clean Air Conservation Act (tested)340 g/l 2 %Date of issue:2 December 2019 Page.

3 1/5 This Technical data Sheet supersedes those previously Technical data Sheet (TDS) is recommended to be read in conjunction with the Safety data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at data SheetHardtop FlexiThe provided data is typical for factory produced products, subject to slight variation depending on description: According to Jotun Performance Coatings' data is valid for mixed gloss may vary depending on the application thickness per coatDry film thicknessWet film thicknessTheoretical spreading rateTypical recommended specification colours may need film thickness in the high end of the recommended specification range to achieve opacity.

4 M mm /l---Surface preparation summary tableSubstrateMinimumRecommendedSt 2 (ISO 8501-1)Carbon steelSa 2 (ISO 8501-1)Stainless steelThe surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface steelThe surface shall be clean.

5 Dry and appear with a rough and dull blast-cleaning using non-metallic abrasive leaving a clean,rough and even surfacesClean, dry and undamaged compatible coatingClean, dry and undamaged compatible coatingSurface preparationApplication methodsThe product can be applied byApplicationSurface preparationTo secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any of issue:2 December 2019 Page: 2/5 This Technical data Sheet supersedes those previously Technical data Sheet (TDS) is recommended to be read in conjunction with the Safety data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at data SheetHardtop FlexiSpray:Use air spray or airless :May be used.

6 Care must be taken to achieve the specified dry film :May be used. Care must be taken to achieve the specified dry film mixing ratio (by volume)Hardtop Flexi Comp A4part(s)part(s)1 Hardtop Flexi Comp B Thinner/Cleaning solventThinner: Jotun Thinner No. 10 Jotun Thinner No. 26 is supplied and used in USA due to Thinner No. 26/Nozzle tip (inch/1000):Pressure at nozzle (minimum):Guiding data for airless spray15-21150 bar/2100 psiNozzle tip:Pressure at nozzle (minimum):Guiding data for air sprayHVLP: 13-21 (inch/1000) / Pressure pot: (mm)HVLP: bar/34 psi / Pressure pot: bar/34 psiDrying and Curing timeSurface (touch) dryWalk-on-dry6 h3 h1 h16 h8 h4 h2 h15 d10 d7 d4 dSubstrate temperature5 C10 C23 C40 CDried/cured for serviceDry to over coat, minimum12 h6 h3 hWalk-on-dry.

7 Minimum time before the coating can tolerate normal foot traffic without permanent marks,imprints or other physical and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the to over coat, minimum: The recommended shortest time before the next coat can be (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal for service: Minimum time before the coating can be permanently exposed to the intended maximum overcoating intervals, refer to the Application Guide (AG) for this of issue:2 December 2019 Page: 3/5 This Technical data Sheet supersedes those previously Technical data Sheet (TDS) is recommended to be read in conjunction with the Safety data Sheet (SDS) and the Application Guide (AG) for this product.

8 For your nearest local Jotun office, please visit our website at data SheetHardtop FlexiInduction time and Pot lifePot life1 hPaint temperature23 CTemperatureDry, atmosphericHeat resistance C120 ContinuousPeak140 CPeak temperature duration max. 1 temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these to spills of most oils, aliphatic petroleum products and non aggressive compatibilityDepending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact Jotun for specific system coat:epoxy, zinc epoxy, epoxy mastic, polyurethanePackaging (typical)The volume stated is for factory made colours.

9 Note that local variants in pack size and filled volumes can vary due to local of containers(litres)Hardtop Flexi Comp B 1 / 4 Hardtop Flexi Comp A4 / 165 / 201 / 5 Storage The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with life at 23 C2448 Hardtop Flexi Comp AHardtop Flexi Comp B month(s)month(s)Volume(litres)Date of issue:2 December 2019 Page: 4/5 This Technical data Sheet supersedes those previously Technical data Sheet (TDS) is recommended to be read in conjunction with the Safety data Sheet (SDS) and the Application Guide (AG) for this product.

10 For your nearest local Jotun office, please visit our website at data SheetHardtop FlexiIn some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun 's Technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the and safetyPlease observe the precautionary notices displayed on the container.