Technical data sheet R3..-BL.. - belimo.ch

1 Technical data ball valve, 3-way, Internal thread For open and closed cold and warm water systems For switching functions and 2-point controls on the water side of air handling units and heating systems Air bubble tightType overviewTypeDN[ ]Rp[ ]kvs[ m /h]PN[ ]R3015-BL1151 1/4916R3032-BL3321 1/41516R3040-BL3401 1/21416R3040-BL4401 1/24716R3050-BL35022416R3050-BL45027516 Technical dataFunctional data MediaCold and warm water, water with glycol up to max. 50% vol. Medium C Medium temperature noteAt a medium temperature of C, a spindle heating or a valve neck extension is allowed media temperature can be limited, depending on the type of actuator. Limitations can be found in the respective data sheets of the actuators. Permissible pressure ps1600 kPa Closing pressure ps500 kPa Differential pressure pmax350 kPa Differential pressure note200 kPa for low-noise operation Leakage rateLeakage rate A, air-bubble-tight (EN 12266-1) Pipe connectorInternal thread according to ISO 7-1 Angle of rotation90 Installation positionUpright to horizontal (in relation to the stem) MaintenanceMaintenance-freeMaterials HousingBrass body nickel-plated Closing elementchrome-plated brass StemNickel-plated brass Stem sealO-ring EPDM Ball seatPTFE, O-ring EPDMS afety notes!

2 The valve has been designed for use in stationary heating, ventilation and air-conditioning systems and must not be used outside the specified field of application, especially in aircraft or in any other airborne means of transport. Only authorised specialists may carry out installation. All applicable legal or institutional installation regulations must be complied during installation. The valve does not contain any parts that can be replaced or repaired by the user. The valve may not be disposed of as household refuse. All locally valid regulations and requirements must be en-gb 2018-02-06 subject to changes1 When determining the flow rate characteristic of controlled devices, the recognised directives must be featuresMode of operationThe change-over ball valve is adjusted by a rotary actuator. The rotary actuator is connected by an open-close accessories Spindle heating DN 15-50 (20W)ZR24-2 DescriptionTypeMechanical accessories Pipe connector to ball valve DN 15 Rp 1/2 ZR2315 Pipe connector to ball valve DN 20 Rp 3/4 ZR2320 Pipe connector to ball valve DN 25 Rp 1 ZR2325 Pipe connector to ball valve DN 32 Rp 1 1/4 ZR2332 Pipe connector to ball valve DN 40 Rp 1 1/2 ZR2340 Extension KitZR-EXT-01 Pipe connector to ball valve DN 50 Rp 2 ZR2350 Installation notesRecommended installation positionsThe ball valve can be installed upright to horizontal.

3 The ball valve may not be installed in a hanging position, with the stem pointing 90 Water quality requirementsThe water quality requirements specified in VDI 2035 must be adhered valves are regulating devices. For the valves to function correctly in the long term, they must be kept free from particle debris ( welding beads during installation work). The installation of suitable strainer is valves and rotary actuators are any service work on the final controlling device is carried out, it is essential to isolate the rotary actuator from the power supply (by unplugging the electrical cable if necessary). Any pumps in the part of the piping system concerned must also be switched off and the appropriate slide valves closed (allow all components to cool down first if necessary and allways reduce the system pressure to ambient pressure level).The system must not be returned to service until the ball valve and the rotary actuator have been correctly reassembled in accordance with the instructions and the pipeline has been refilled by professionally trained ball valve, 3-way, Internal threadSafety en-gb 2018-02-06 subject to changes2 Flow directionPlease also ensure that the balls are in the correct position (marking on the spindle).

4 Normally, the port designation AB is the quantity constant with 3-way valves. In the case of the BL versions, port B is designated the quantity A = 0%B AB = 100%B A = 100%B AB = 0%Dimensions / WeightDimensional drawingsRpmin. YMHmin. XL42L1L1: Maximum screwing : Minimum distance with respect to the valve actuator dimensions can be found on the respective actuator data [ ]Rp[ ]L[ mm]L1[ mm]M[ mm]H[ mm]X[ mm]Y[ mm]Weight[ kg]R3015-BL1151 1 1 1 1 documentation Overview Valve-actuator combinations Data sheets for actuators Installation instructions for actuators and/or ball valves General notes for project ball valve, 3-way, Internal threadInstallation en-gb 2018-02-06 subject to changes3