TECHNICAL MANUAL - HVACDirect.com

1 Refer to Service MANUAL RS6200006 for installation, operation, and troubleshooting information. All safety information must be followed as provided in the Service MANUAL . Refer to the appropriate Parts Catalog for part number information. Models listed on page 2012 Copyright 2007 - 2012 Goodman Manufacturing Company, MANUAL is to be used by qualified, professionally trained HVAC techniciansonly. Goodman does not assume any responsibility for property damage orpersonal injury due to improper service procedures or services performed by anunqualified MANUTECHNICAL MANUTECHNICAL MANUTECHNICAL MANUTECHNICAL MANUALALALALALGSX 13 SEER Single PhaseCondensing Units with R-410 APRODUCT IDENTIFICATION2 The model number is used for positive identification of component parts used in manufacturing.

2 Please use this numberwhen requesting service or parts VOLTAGE!Disconnect ALL power before servicing or installing this unit. Multiple powersources may be present. Failure to do so may cause property damage, personalinjury or and repair of this unitshould be performed ONLY by in-dividuals meeting (at a minimum)the requirements of an "entry level technician", as speci-fied by the air conditioning , Heating, and RefrigerationInstitute (AHRI). Attempting to install or repair this unitwithout such background may result in product damage,personal injury or will not be responsiblefor any injury or property damagearising from improper service orservice procedures.

3 If you install or perform service onthis unit, you assume responsibility for any personalinjury or property damage which may result. Many juris-dictions require a license to install or service heating andair conditioning :S: Split SystemPRODUCT TYPE:C: Condenser R-22X: Condenser R-410AH: heat Pump R-22Z: heat Pump R-410 ASEER:SEER RatingBRAND:G: Goodm an Brand(Sta nda rd Fea tu re Se t Mo del )S: Goodman DeluxeV: ValueNOMINALCAPACITY018: Tons024: 2 Tons030: tons036: 3 Tons042: Tons048: 4 Tons060: 5 tonsELECTRICAL:1: 208-230v 1ph/60Hz3: 208-230v 3ph/60Hz4: 460v 3ph/60 HzMAJOR REVISION:A: Initial Relea seMINOR REVISION:A.

4 Init ial ReleasePRODUCT IDENTIFICATION3 The United States Environmental Protection Agency ( EPA ) has issued various regulations re-garding the introduction and disposal of refrigerants introduced into this unit. Failure to followthese regulations may harm the environment and can lead to the imposition of substantial regulations may vary by jurisdiction. Should questions arise, contact your local EPA not connect or use any devicethat is not design certified by Good-man for use with this unit. Seriousproperty damage, personal injury, reduced unit perfor-mance and/or hazardous conditions may result from theuse of such non-approved prevent the risk of propertydamage, personal injury, or death,do not store combustible materi-als or use gasoline or other flammable liquids or vaporsin the vicinity of this model number is used for positive identification of component parts used in manufacturing.

5 Please use this numberwhen requesting service or parts information.* Indicates minor revision & is not used for order entry or inventory managementGSX130181A*GSX130241A*GSX13030 1A*GSX130361A*GSX130421A*GSX130481A*GSX1 30601A*GSX130611A*GSX130181B*GSX130241B* GSX130301B*GSX130361B*GSX130421B*GSX1304 81B*GSX130601B*GSX130181C*GSX130361C*GSX 130181D*GSX130241D*GSX130301D*GSX130361D *GSX130181E*GSX130361E*PRODUCT DESIGN4 GSX13 models are available in 1 1/2 through 5 ton sizes anduse R-410A refrigerant. They are designed for 208/230 voltsingle phase condenser air is pulled through the condenser coil by adirect drive propeller fan.

6 This condenser air is then dis-charged out of the top of the units are designed for free air discharge, so no addi-tional resistance like duct work shall be suction and liquid line connections on present modelsare of the sweat type for field piping with refrigerant type cop-per. Front seating valves are factory installed to accept thefield run copper. The total refrigerant charge for a normal in-stallation is factory installed in the condensing unit. GSX unitsare charged for the matching evaporator coil and a 15 footrefrigerant line should be properly sized by heat gain and losscalculations made according to methods of the Air Condi-tioning Contractors Association (ACCA) or equivalent.

7 It isthe contractors responsibility to ensure the system has ad-equate capacity to heat or cool the conditioned models use the Copeland Scroll "Ultratech" Series com-pressors which are specifically designed for R-410A refriger-ant. There are a number of design characteristics which aredifferent from the traditional reciprocating and/or scroll com-pressors."Ultratech" Series scroll compressors will not have a dis-charge thermostat, some of the early model scroll compres-sors required discharge to their design Scroll compressors are inherently moretolerant of small quantities of liquid : Even though the compressor section of a Scroll com-pressor is more tolerant of liquid refrigerant, continuedfloodback or flooded start conditions may wash oil from thebearing surfaces causing premature bearing failure.

8 "Ultratech" Series scroll compressors use "POE" orpolyolester oil which is NOT compatible with mineral oil basedlubricants like 3GS. "POE" oil must be used if additional oilis pressures and amp draws may differ from stan-dard reciprocating and/or scroll compressors. This informa-tion may be found in the "Cooling Performance Data" NOTE: Because of the potential damage tocompressors, do not allow suction pressure at service valveto drop below 20 PSIG when pumping unit system down forrepair. Outdoor section, depending on line set length andamount of charge in system, may not be able to hold theentire system avoid possible injury, explosion or death, practicesafe handling of consideration must be given to location of the con-densing unit(s) in regard to structures, obstructions, otherunits, and any/all other factors that may interfere with aircirculation.

9 Where possible, the top of the unit should becompletely unobstructed; however, if vertical conditions re-quire placement beneath an obstruction there should be aminimum of 60 inches between the top of the unit andthe obstruction(s). The specified dimensions meet require-ments for air circulation only. Consult all appropriate regula-tory codes prior to determining final important consideration in selecting a location forthe unit(s) is the angle to obstructions. Either side adjacentthe valves can be placed toward the structure provided theside away from the structure maintains minimum service clear-ance.

10 Corner installations are strongly NOT locate the unit: Directly under a vent termination for a gas TypeABCAAR esidential10"10"18"20"Light Commercial12"12"18"24"Minimum Airflow Clearance Within 3 feet of a clothes dryer vent. Where the refreezing of defrost water would create ahazard. Where water may rise into the !OK!AAAAAACCCCOK!OK!OK!OK!NOTRECOMMENDED AAAAAAAAAABBBBPRODUCT DESIGN5 DIMENSIONSWDHM odelDimensions - W x D x HGSX130181A*26" x 26" x 32 "GSX130241A*26" x 26" x 32 "GSX130301A*26" x 26" x 32 "GSX130361A*29" x 29" x 32 GSX130421A*29" x 29" x 34 "GSX130481A*29" x 29" x 38 "GSX130601A*35 " x 35 " x 38 "GSX130611A*35 " x 35 " x 38 "GSX130181B*26" x 26" x 27 "GSX130241B*26" x 26" x 27 "GSX130301B*26" x 26" x 27 "GSX130361B*29" x 29" x 28 "GSX130421B*29" x 29" x 36 "GSX130481B*29" x 29" x 36 "GSX130601B*29" x 29" x 40"ModelDimensions - W x D x HGSX130181C*26" x 26" x 27