Technical Notes - COSEL

1 1 Outline of Power Supply2 Circuit Method of Switch mode Power Supply3 Glossary of term374 Notes on operationTechnical Notes385 Electromagnetic Interference6 Power Factor Correction7 Reliability8 Safety Standards9 Standards and Regulations for Switch mode Power Supply10 Disclaimer38394247495252535538 Regulated DC voltage is required for semiconductor devices suchas ICs and Transistors to function. Regulated voltage can be gen-erated from commercial AC lines with an AC to DC power supply orfrom DC power source (such as Batteries) with a DC to DC type is further classified to one that is isolated between pri-mary (Input) circuit and secondary (Output) circuit or the past 15 years, there have been significant changes inthe design of power supplies.

2 The most important of these hasbeen widespread change from linear regulator to switch modepower supplies (SMPS). The principal reason for the move toswitch mode power supplies is their much greater efficiency typi-cally 65 - 90% as opposed to 25 - 50% for the linear regulator. Thisgreatly reduces the cooling requirement, and allows a much higherpower Circuit diagram of Switch mode Power Supply1 Outline of PowerSupply2 Circuit Method ofSwitch modePower SupplyTable Compares some of the features of Switch modePower Supplies with Linear RegulatorsModeItemEfficiencyStabilizatio nRipple NoiseResponse speedEMII nput voltageCircuitSizeWeight65 - 90%Normal10 - - 10mSWide interference spectrumWide input rangeComplicatedSmall(1/4 - 1/10 of Linear regulator)

3 Light(1/4 - 1/10 of Linear regulator)25 - 50%ExcellentLess than 10mV10 S - 1mS Magnetic interference for source frequencyNarrow input rangeSimpleLargeHeavySwitch mode Power SupplyLinear RegulatorThe method of switch mode power supply is classified by circuitmethod of DC-DC converter. There are 2 methods for oscillator:self-oscillating converter where positive feedback from the powertransformer to provide the oscillatory behavior, and separate-course oscillator with PWM control changes operating frequency depending on inputvoltage and load, but separate-course oscillator does not changeoperating AMPP rotectionCircuitInputRectifierOutputRect ifierConverterInrushCurrentlimiting1) Forward shows the power stage of a typical single-ended forwardconverter.

4 Since the output inductor L carries a large DC currentcomponent, the term choke will be used to describe this the general appearance of the power stage is similar tothat of the flyback unit, the mode of operation is entirely secondary winding S is phased so that energy will be trans-ferred to the output circuits when the power transistor TR is power transformer T operates as a true transformer with a lowoutput resistance, and therefore a choke L is required to limit thecurrent flow in the output rectifier D , the output capacitor C , andthe Forward converter2) Push-pull converterA power switching circuit which uses a centertapped transformerand two power switches which are driven ON and OFF alterna-tively.

5 This circuit does not provide regulation by Push-pull converterTechnical NotesForward converter and flyback converter are methods of transferof energy from primary to secondary source. The forward convertertransfers energy when the switching transistor is ON (ON-ON con-verter), but flyback converter transfers the energy when transistoris OFF (ON-OFF converter). Half-bridge converter4) Full-bridge converterA power switching circuit in which four transistors are connectedin a bridge configuration to drive a transformer Full-bridge converter5) Flyback converterA power supply switching circuit which normally uses a single tran-sistor.

6 During the first half of the switching period the transistor isON and energy is stored in a transformer primary; during the sec-ond half period this energy is transferred to the transformer sec-ondary and the Flyback converter6) Buck regulatorIn buck regulators, the output voltage will be of the same polaritybut always lower than the input voltage. One supply line must becommon to both input and output. This may be either the positiveor negative line, depending on the regulator Buck regulator7) Boost regulatorIn boost regulators, the output voltage will be of the same polaritybut always higher than the input voltage.

7 One supply line must becommon to both input and output. This may be either the positiveor negative line, depending on the Boost regulator8) Buck-boost regulatorIn buck-boost regulators, the output voltage is of opposite polarityto the input, but its value may be higher, equal, or lower than that ofthe input. One supply line must be common to both input and out-put, and either polarity is possible by + Buck-boost regulator3) Half-bridge converterA power switching circuit similar to the full bridge converter ex-cept that only two transistors are used, with the other two replacedby Glossary of term1) Input voltage rangeThe high and low input voltage limits within which a power supplyor DC-DC converter meets its () ave E()

8 Sinusoidal voltage wave formTechnical Notes40 Maximum ValueEffective ValueAverage ValueEmE (rms)E (ave)====1TT0edt212 EmEm2TT20edt222) Input current of shows the typical voltage and current wave forms at the in-put to a SMPS. Current only flows to charge the capacitors whenthe rectified input voltage exeeds the voltage stored. Pulses of cur-rent are drawn from the supply near the peak point of the AC volt-age Input wave form of SMPSI nput Current (rms) =Output PowerInput Voltage (rms) Efficiency Power Factor3) Input PowerIt can be seen that the input voltage is only slightly distorted bythe very non-linear load presented by the capacitor input filter.

9 Thesinusoidal input is maintained because the line input resistance isvery low. The input current however, is very distorted and discontin-uous, but superficially would appear to be a part sine wave inphase with the voltage. This leads to a common error: The productVx Iis assumed to give input power. This is not so! Theproduct is the input volt-ampere product; it must be multiplied bythe power factor (typically for a capacitor input filter) to get reason for the low power factor is that the nonsinusoidal cur-rent wave form contains a large odd harmonic content, and thephase and amplitude of all harmonics must be included in the Power = E(rms) I(rms)Active Power = Apparent Power Power Factorin (rms)in (rms)4) EfficiencyThe ratio of total output power to active power, expressed in per-cent.

10 This is normally specified at full load and nominal input ) Inrush currentThe peak instantaneous input current drawn by the SMPS atswitch The Series Resistor TechniqueFor low-power applications, simple series resistor may be , a compromise must be made, as a high value of resis-tance, which will give a low inrush current, will also be verydissipative under normal operating conditions. Consequently, acompromise selection must be made between acceptable inrushcurrent and acceptable operating Series Resistor Techniqueb.