TECHNICAL REGULATION OF THE CUSTOMS …

1 TR CU 010/2011 1 APPROVED by Decision of the Commission of the CUSTOMS union of October 18, 2011 N 823 TECHNICAL REGULATION OF THE CUSTOMS union TR СU 010/2011 ON SAFETY OF MACHINES AND EQUIPMENT This is an unofficial translation made by the EU funded project Approximation of EU and Russia TECHNICAL REGULATION , standardization and certification systems, Russia and can in no way be considered as an official document.

2 2 Contents Foreword 3 Article 1. Scope 3 Article 2. Definitions 4 Article 3. Rules of placing on the market 6 Article 4. Provision of safety of machines and (or) equipment at the stage of design (construction) 6 Article 5.

3 Provision of safety of machines and (or) equipment at the stages of manufacture, storage, transportation, operation and disposal 8 Article 6. Provision of compliance with safety requirements 10 Article 7. Conformity assessment 10 Article 8. Conformity assurance 10 Article 9. Procedure for declaration of conformity of machines and (or) equipment 12 Article 10.

4 Composition of the documents being the ground for issue of a declaration of conformity 13 Article 11. Procedure for certification of machines and (or) equipment 14 Article 12. Marking by a single mark of placing the products on the market of the Member States of the CUSTOMS union 17 Article 13. Safeguard clause 17 Annex N 1. Essential safety requirements for machines and (or) equipment 18 Annex N 2. Additional safety requirements for particular categories of machines and (or) equipment 27 Annex N 3.

5 List of the objects of TECHNICAL REGULATION subject to conformity assurance 36 TR CU 010/2011 3 Foreword 1. This TECHNICAL REGULATION has been developed in accordance with the Agreement on common principles and rules of TECHNICAL REGULATION in the Republic of Belarus, the Republic of Kazakhstan and the Russian Federation of November 18, 2010. 2. This TECHNICAL REGULATION has been developed with a purpose to establish in the single CUSTOMS territory of the CUSTOMS union common requirements mandatory to apply and implement the requirements for machines and (or) equipment as well as the requirements for design (construction), manufacture, installation, setting up, operation, storage, transportation, marketing and disposal, provision of free movement of machines and (or) equipment placed on the market of the single CUSTOMS territory.

6 3. In case other TECHNICAL regulations of the CUSTOMS union , TECHNICAL regulations of the Eurasian Economic Community (further EurAsEC) establishing the requirements for machines and (or) equipment may be adopted, machines and (or) equipment must comply with the requirements of these TECHNICAL regulations of the CUSTOMS union and EurAsEC, which are applied to them. Article 1. Scope 1. This TECHNICAL regulations applies to machines and (or) equipment placed on the market in the CUSTOMS territory of the CUSTOMS union . 2. This TECHNICAL REGULATION defines the minimum necessary requirements for safety of machines and equipment during design (construction), manufacture, installation, setting up, operation, storage, transportation, marketing and disposal for the purposes of safety of life or health of citizens, property, protection of environment, life and health of animals and prevention of the actions misleading the consumers.

7 3. This TECHNICAL REGULATION applies to all machines and (or) equipment, for which the hazards are identified and the requirements for disposal and reduction are specified in accordance with Annexes NN 1 and 2. 4. This TECHNICAL REGULATION doesn t apply to the following machines and (or) equipment: - machines and (or) equipment related to integrity and stability of functioning of the communication network and use of the radio-frequency spectrum; - machines and (or) equipment for medical purposes and used in direct contact with a patient (X-ray, diagnostic, therapeutic, orthopedic, dental and surgical equipment); - machines and (or) equipment, specially designed for application in nuclear industry.

8 For machines and (or) equipment of general purposes used in nuclear industry this TECHNICAL REGULATION applies to the extent not contradicting the requirements of nuclear and radiation safety; - wheeled transport except for machines and (or) equipment installed on it; 4 - marine and river transport (ships and floating means and machines and (or) equipment used on them); - space and aircraft; - railway equipment and TECHNICAL means specially designed for use in railway transport and subway; - attractions; - weapons and military equipment; - machines and (or) equipment designed for use by handicapped people; - agricultural and forest tractors and trailers, except for machines and (or) equipment mounted on them; - drilling platforms except for machines and (or) equipment, which are used on them.

9 5. This TECHNICAL REGULATION applies to machines and (or) equipment used at industrial hazardous facilities. 6. Where the risks caused by machines and (or) equipment are specified in full or partially in other TECHNICAL regulations of the CUSTOMS union and EurAsEC, machines and (or) equipment must meet the requirements of TECHNICAL regulations of the CUSTOMS union , EurAsEC, which are applied to them. 7. Identification of machines and (or) equipment is understood as establishment of conformity of specific machines and (or) equipment with a sample or their description, for which purpose standards indicated in Article 6 of this TECHNICAL REGULATION , classifiers, specifications and drawings, TECHNICAL specifications, operational documentation can be used.

10 8. Additional safety requirements for particular categories of machines and (or) equipment are set up in accordance with Annex N 2. Article 2. Definitions 1. In this TECHNICAL REGULATION the following terms and definitions are used: - failure of machines - destruction or damage of machines and (or) equipment resulting in operation of machines and (or) equipment, uncontrollable explosion and (or) emission of dangerous and harmful substances; - "admissible risk" - risk effect from application of a machine and (or) equipment proceeding from TECHNICAL and economic capabilities of a manufacturer appropriate to a level of safety, which should be ensured at all stages of life cycle.