Tecnical ata Technical Data VAC-P – MicroSet PIR …

1 Technical DataEffective November 5, 2014 VAC-P MicroSet PIR Low voltage vacancy ceiling SensorOverviewThe MicroSet Passive Infrared Low voltage vacancy ceiling sensor increases energy savings by requiring a Manual On input to turn on the MicroSet self-adjusting time delay and sensitivity Optional built-in light level sensor Optional BAS/HVAC isolated relay Products tested to NEMA WD 7 - 2011 Occupancy Motion Sensors Standard Requires Manual On for activationCatalog#Prepared byProjectDateCommentsTypeTechnical Data PIRA ctivatedMicroSet Self-Adjusting2 Technical Data November 2014 VAC-P MicroSet PIR Low voltage vacancy ceiling sensor Infrared (PIR)Power Requirements Input10-30 VDC from Greengate Switchpack or Greengate systemMaximum current needed is 25mA per sensorOutputOpen collector output to switch up to ten Greengate SwitchpacksBAS with an Isolated Form C Relay in (-R) modelIsolated Form C Relay Ratings: 1A 30 VDC/VACTime DelaysSelf-adjustable, 15 seconds/test (10 min.)

2 Auto), or Selectable 5, 15, 30 minutes, or Zero Time DelayCoverage500 and 1500 sq. Level Sensing (-R Models)0 to 300 foot-candlesOperating EnvironmentTemperature: 32 F - 104 F (0 C - 40 C)Relative humidity: 20% to 90%, non-condensingFor indoor use onlyHousingDurable, injection molded housing. Polycarbonate resin complies with UL H x W ( x )MountingMounts directly to a ceiling tile, to a 4 square box and round mud ring or to a 4" octagon boxLED IndicatorsRed LED for PIR detectionStandardsFCC CompliantcULus ListedRoHS Compliant Description/OperationThe Passive Infrared (PIR) sensor monitors space occupancy to deliver maximum energy savings. The sensor includes self-adaptive technology that continuously self-adjusts sensitivity and time delay in real-time, maximizing the potential energy savings that are available in the particular application.

3 The lights are turned ON by activating a momentary switch (model # GMDS-*) that is connected to the sensor . The MicroSet Passive I nfrared Low voltage ceiling sensor has an ambient light level sensor . When enabled, the Daylighting feature prevents lights from turning ON when the room is adequately illuminated by natural light. PIR sensors are considered line-of sight sensors, meaning that the sensor must be able to have a direct line-of-sight to the person making the Conference Rooms Open Office Areas Small Private Offices Common Areas Break Rooms Restrooms (Non-Partitioned) Utility Closets3 Technical Data November 2014 VAC-P MicroSet PIR Low voltage vacancy ceiling sensor Diagrams BLACK (COMMON) BROWN (BLUE CONTROL) YELLOW (CONTROL-OCC/DAY) PURPLE (NORMALLY CLOSED) GRAY (ISOLATED RELAY COMMON) ORANGE (NORMALLY OPEN) WHITE/BROWN (YELLOW CONTROL)OAC AND VAC MANUAL MODE OPERATION:1.

4 SWITCHES ARE REQUIRED TO TURN CORRESPONDING LOADS ON. 2. LOADS TURN OFF WHEN sensor TIMES OUT OR WITH IF DAYLIGHT sensor IS ENABLED AND LIGHT LEVEL IS ABOVE SETPOINT, SWITCHPACK CONNECTED TO YELLOW LEAD WILL NOT TURN LOAD AUTOMATIC MODE OPERATION:1. WHEN sensor ACTIVATES, BOTH LOADS TURN ON. 2. SWITCHES CAN BE USED TO TURN LOADS ON OR IF DAYLIGHT sensor IS ENABLED AND LIGHT LEVEL IS ABOVE SETPOINT, SWITCHPACK CONNECTED TO YELLOW LEAD WILL NOT TURN LOAD ON. RECOMMENDED WIRE:18-3 AWG STRANDED WIRE SHIELDED OR NON/SHIELDED BLUE (CONTROL-OCC) RED (10-30 VDC)LOAD "A"BLUENEUTRALHOT**USE BLACK LEAD FOR 120 VAC. USE ORANGE LEAD FOR 277 VAC.

5 CAP UNUSED **HOTWHITEBLUESWITCH-PACKLOAD "B"BLUENEUTRALHOT**USE BLACK LEAD FOR 120 VAC. USE ORANGE LEAD FOR 277 VAC. CAP UNUSED **HOTWHITEBLUESWITCH-PACK BLACK (COMMON)BLUE (CONTROL) RED (15 VDC)MODEL GMDS - LOAD "B"(NORMALLY OPENMOMENTARY SWITCH)MODEL GMDS - LOAD "A"(NORMALLY OPENMOMENTARY SWITCH) BLACK (COMMON)BLUE (CONTROL) RED (15 VDC)NOTES1. LOADS MAY BE ON SAME CIRCUIT OR DIFFERENT CIRCUITS OR SP20-MV SWITCHPACK SHOWN. 120/277 VAC 20 AMP Model*Wiring diagram for single sensor application. Visit our website for other wiring 500 sq. 1500 sq. Mounting Height: 8 to 12 ft( m)10 ft(3 m)5 ft( m)005 ft( m)10 ft(3 m)DT1k020 ft( )3 ft( )15 ft( m)15 ft( m)20 ft( )20 ft( )20 ft( )10 ft(3 m)5 ft( m)10 ft(3 m)5 ft( m)15 ft( m)15 ft( m)Maximum coverage area mayvary somewhat according to roomshape and the presence of NEMA WD 7 Guide and roboticmethod were utilized to verifycoverage Motion, IRMajor Motion, ft( m)03 ft( )12 ft( m)12 ft( m)18 ft( m)18 ft( m)12 ft( m)12 ft( m)18 ft( m)18 ft( m)Eaton1000 Eaton BoulevardCleveland, OH 44122 United s Cooper Controls Business203 Cooper CirclePeachtree City, GA 2014 EatonAll Rights ReservedPrinted in USAP ublication No.

6 ACC141012 November 5, 2014 Eaton is a registered other trademarks are property of their respective Data VAC-P MicroSet PIR Low voltage vacancy ceiling sensor ControlsSweepOverrideLEDs(-R model only)(-R model only)Full/Half LogicHVAC/TrackingZero Time DelayPot 1 - Blue (0-300 FC)Ultrasonic(-R model only)Pot 2 - Green1234567891011 12 ONDaylight sensor AdjustmentPIR DetectorOrderingCatalog #Recommended Room SizeField of ViewFeaturesVAC-P-500-R500 sq. w/ BAS Relay & Daylight SensorVAC-P-1500-R1,500 sq. w/ BAS Relay & Daylight SensorAccessory ComponentsSuggested Low voltage Manual ON Switch(es)GMDS-W