Transcription of The Laser Diode - IU B
1 Advanced Optics LaboratoryDiode Laser Experiment Page 1 of 7 The Laser Diode1 IntroductionThis set of laboratory experiments is primarily design to have you become familiar with the propertiesof Laser diodes and to become familiar with optical spectrum analyzers typically used in fiber and laserinstrumentation to asses spectral characteristics of sources. In addition you will become familiar withthe now common technique of using an optical grating to stabilize and to tune the frequency of a discussion and figures in this section are for the Sharp 780 nm, LT025MD0 Diode Laser .
2 TheSharp Laser is infrared and so for this laboratory you will be working with a 635 nm visible Laser fromHitachi, though for historical reasons we retain the Sharp Diode for the context of this discussion. Thegeneral concepts are relevant to both 1 shows the Diode Laser with a cut-away ofthe housing where the chip mounts. Figure 2 shows thelaser chip structure, typical chip dimensions, thedirection of the forward current, and the radiationpattern. The radiation is produced in the active layer,which is a small fraction of the height of the chip,hence the radiation is diffracted when it emerges fromthe active region analogously to the diffraction ofradiation passing through a narrow slit.
3 The diffractionproduces the radiation pattern shown in Figure 3 shows the optical power output versusforward current and monitor current. The maximumoperating forward current and power output arespecified by the manufacturer for each diodelaser. Figure 4 shows the wavelength versuscase temperature. Figure 5 shows how thepower output depends on the wavelength, wherethe spectral width of the Laser line at 30 mW isabout 20 MHz. The Hitachi Diode that you willbe using is much lower power, about 5 mirrors for a Diode Laser chip are thecleaved facets of the semiconductor, which aresmoother and flatter than any mechanicallypolished mirror.
4 If there are no coatings on theend surfaces of the Laser chip, then thereflectivity R of a surface is given by:Figure 1. Internal structure of the Sharp LT025 MDOdiode 2. Chip structure of the Sharp LT025 MDOdiode Optics LaboratoryDiode Laser Experiment Page 2 of 7 Rnnnncaca=-+ 2,(1)where nc and na, are the indices of refraction of the chip and air, LT025MD0 Diode Laser has a reduced reflective coating on the output facet of the chip;therefore, the reflectivity of this facet is less than that calculated in Exercise 1.
5 The grating reflectivityis about 40%, hence it dominates the front facet of the chip in forming the Laser cavity. Therefore, thelength of the cavity is the distance from the grating to the far chip facet. The purpose of thisconfiguration is to change the Laser wavelength by displacing the PREPARATIONYou will be using a Hitachi Laser Diode from ThorLabs No. HL6316G. Begin by looking over thespecifications sheet for the Diode . In particular you will want to notice the operating current.
6 Youwould normally also note the maximum allowed operating current, but this specification sheet does notprovide it. Instead note the "Typical Characteristics Curves where they show up to about 50 you are ready to begin turning on equipment first find the Melles Griot Inc. Diode laserdriver. When you first turn on the key in enters a safe mode. The "display" indicator shows to see that the "mode" indicator is on "cur" for "current". If not, press it once and the modeshould change from "PWR" or "power" to "Cur. The "output" indicator should read, " the "Level" dial is a hoe labeled "limit".
7 There is a small trimmer potentiometer thatcan be adjusted with a jeweler s screwdriver. You must set this trimmer for the maximum outputcurrent. The digital LED indicator will indicate the limit level in milliamps. Set it to be between 40and 45 3. Optical power output versus forwardcurrent (for three Laser temperatures) andmonitor 4. Emitted waavelength versus casetemperature. Note the Optics LaboratoryDiode Laser Experiment Page 3 of 7 When the mode switch is set to current, the Diode laserdriver will control the current to the Diode so that it remainsat a fixed level determined by the "level" knob.
8 When themode switch is set to power, the driver controls the laserdiode to provide fixed output power. For the entireexperiment leave the mode switch set to the "level" knob all the way set the display indicator to " Laser ". As the level knobis increased in the clockwise direction the current indicatorwill increase. At this time no current is actually going tothe Laser , it only indicates the current that will be suppliedwhen the output is changed to " Laser ". The Laser will beturned on after a few other items are attended on the "Lambda" power supply.
9 It providespower to the Laser Diode temperature controller. Do notchange the knobs. The left hand voltage setting should V, with the current knob all the way up (clockwise).The right hand power supply should be at 15 volts with thecurrent again full on. While you are at it, turn on theoscilloscope and Ando spectrum Laser DIODENow preset the Laser Diode current to about 15 mA and pushthe output button so that it is switched from "preset" to" Laser ". Turn up the level knob so that the current goes upto about 30 mA.
10 Notice the output from the Laser (*DONOT LOOK DIRECTLY INTO THE Laser BEAM!*)The Laser should have a collimating lens in front of it, andnothing else. If there is other optics in the way, such asgrating, move it so that you can see the Laser output on thewall of the the brass-colored photodetector module you willmeasure the power output as a function of current andtemperature. Make sure that the photodiode is powered with a Lemo cable from the small bass-coloredpower supply on the optical a BNC cable from the photodiode output to the oscilloscope.
