The V8-5V Engine - kpematop.com

1 Service. For internal use onlyAll rights reserved. Subject to technical modifications. AUDI AGAbteilung I/VK-5D-85045 IngolstadtFax 0841 status 02/99 Printed in Germany The V8-5V Engine Construction Features and Functions Self-Study Programme 217 217 217 2 SSP217_048 AUDI has been producing advanced 8-cylinder engines since 1988. Their capacity has increased from l to l. The V8 Engine in combination with Aluminium Space Frame technology was the technical basis for Audi's breakthrough into the luxury to enhance the value of the Audi A8 have included the redesign of the V8 new V8-5V engines are now also available for the Audi A6 model range.

2 3 Engine - Motronic Subsystems Variable intake manifold .. 27 Secondary air system .. 32 Content IntroductionEngine - Mechanics Crankgear .. 6 Engine mounting .. 9 Engine lubrication .. 10 Cooling circuit .. 16 Cylinder headFive-valve technology .. 19 Roller rocker .. 20 Camshaft adjuster .. 22 Toothed-belt drive; cylinder-head seal .. 24 Cylinder-head cover seal .. 25 Exhaust manifold .. 26 Technical data .. 5 The self-study programme is not a repair manual! The self-study programme provides you with information concerning the Engine 's construction features and functions.

3 New!Caution!Important! Page When carrying out maintenance and repair work, it is essential to use the latest technical literature. Engine Management System overview .. 36 Function diagram .. 38 Quick-start functionsCamshaft position sensor .. 40 Engine run-down sensor .. 41 Electronic throttle function .. 42 CAN bus interfaces .. 44 Additional signals / interfaces .. 46 Service .. 49 4 New features Five-valve cylinder head with roller rocker Camshaft adjustment 3-stage variable intake manifold Engine management system, Bosch ME Electro-hydraulic Engine mounting Modifications to crankcase and crankgear to oil circuit to cooling circuit V8-5V Engines Introduction SSP213_073 Major modifications were made to the V8 engines during the course of further development.

4 Emphasis was placed on the following development objectives: compliance with future exhaust-emission regulations reduction of fuel consumption increase in torque and power improvement of comfort and convenience reduction of Engine weight increased use of shared components for the AUDI Engine following new features and modifications have been incorporated in the V8 4-valve Engine . 5 Technical data The specified power data is only possible if 98 RON fuel is used. A reduction in power output must be expected if 95 RON fuel is used.

5 L V8-5V l V8-5V Engine 0501001502002503003504004505000255075100 12515017520022525001000 2000 3000 4000 5000 6000 7000 05010015020025030035040001000 2000 3000 4000 5000 6000 70000255075100125150175200 SSP217_004 SSP217_005 Torque (Nm)Speed (rpm)Power output (kW)Torque (Nm)Speed (rpm)Power output (kW) lEngine codeAQGAQF (A8)ARS (A6)DesignV8 Engine with 90 o V angleCapacity3697 cm 3 4172 cm 3 Power output191 kW 260 hp at6000 rpm228/220 kW 310/300 hpat 6000 rpmSpecif. hp/lTorque350 Nm at3200 rpm410 Nm at3000 rpmSpecif.

6 MmCompression ratio11:111:1 Weight198 kg200 kgEnginemanagementMotronic ME RONF iring sequence1 - 5 - 4 - 8 - 6 - 3 - 7 - 2 Exhaust-emis-sion standardEU 3 6 Engine - Mechanics Crankgear The crankcase has been adapted to the modifications made to the oil supply system and cooling conrods have been used for the l Engine since 1995 and are now also being used for the l conrods are shared components used in both the l and l Engine . SSP217_054 SSP217_006 7 Owing to the design of the valve recesses, the pistons are specifically intended for use in the appropriate cylinder bank only.

7 SSP217_055 SSP217_002 8 Engine - Mechanics The locking mandrel ( 3242) used for the V6 engines is also used for locking the crankshaft. It is applied to the crank web of the 4th cylinder and is used for basic Engine adjustment and also as a counterhold for loosening and tightening the central bolt of the crankshaft. SSP217_009 The 5th cylinder must be set to ignition TDC. SSP217_007 Wide, milled ventilation recesses above the thrust bearings reduce pumping are also inserted at the side of the two front crankshaft bearing caps to improve running smoothness (see SSP 198, page 6).

8 9 The central bolt does not have to be unscrewed for the vibration damper to be marking indicates the ignition TDC of the 5th cylinder. SSP217_050 Central boltMarking Engine mounting To enhance driving comfort, hydraulic Engine mounts with electrical activation are used for the 8-cylinder function in the way as described in SSP 183 mounts are activated by the Engine control unit according to Engine speed and vehicle speed. Electrical connection SSP217_039 10 Engine - Mechanics SSP217_010 A duocentric oil pump driven by the cranks-haft via a chain replaces the previously used external gear oil duocentric oil pump extends deep into the oil sump.

9 The low suction height means that the oil pressure can build up quickly, especially with oil-pressure control valve is located in the oil pump housing. The diverted oil is led off to the intake side of the oil pump. This helps optimise the level of the intake spindle shafts, there are 5 oil bores per triple roller rocker . Three oil bores each supply one hydraulic tappet. Two oil bores supply the oil-spray bores integrated in the roller rocker to lubricate the rollers. The oil-spray bores are only opened when the roller rockers are actuated.

10 This results in a reduction of the amount of oil required in the cylinder head. Oil-level sensorTriple roller rocker The roller rockers are described on pages 20 and 21. Engine lubrication 11 BAABBPAA SSP217_011 Throttle Cylinder bank 1 Oil retention valvesSpray jet valveBypass valvesOil filter moduleOil sumpOil pressure control valveCamshaft Cylinder bank 2 Oil flow (pressurised)Oil flow (non-pressurised) ThrottleDuocentric oil pumpFilter elementOil cooler Slight modifications have been made to the oil circuit in the cylinder oil circuit for cylinder bank 2 shown in the illustration is the oil circuit that has been used since the introduction of the new model.