This is your one stop 4 Speed Toploader shop.

1 David Kee Toploader Transmissions, Inc. specializes in Ford 4 speed toploader transmissions from 1964 to 1973. We are the world s largest manufacturer of high quality 4 speed toploader parts. We can remanufacture your Toploader , sell you one outright or take yours in exchange. If you need parts for your Toploader we can provide you with anything you need. We also sell 8" and 9" third members and parts, Quicktime bellhousings, Hurst shifters, McLeod clutches and Spicer drive shaft yokes. In addition, we are an authorized Jerico Racing Transmission is your one stop 4 speed toploader of our parts are also available online. Visit our website at: Mogford RoadSAN ANTONIO, TEXAS 78264 Phone: 210-626-1483 Fax: VIEW OF A TOPLOADEREXPLODED VIEW OF A TOPLOADERUse this picture to determine what parts you need. Refer to the information on the opposite page for part numbers NumberNumberDescriptionPart Number1 Bearing RetainerDK296-1 &1A37 Speedometer Drive Gearpage 52 BoltDK296-238 Rear BearingDK296-38 & 38A3 Front SealDK296-3 & 3A39 Snap Ring (Rear Bearing)DK296-394 Bearing Retainer GasketDK296-440 Thrust Washer (First Gear)DK296-405 Input ShaftDK296-5 thru 5C41 First GearDK296-416 Front BearingDK296-6 & 6A421-2 Synchronizer AssemblyDK296-427 Snap Ring (Bearing)DK296-7431-2 Synchronizer KeysDK296-438 Snap Ring (Input Shaft)

2 DK296-844C-SpringDK296-449 Needle BearingsDK296-945 Bronze Blocker RingDK296-4510 Main CaseDK296-1046 Snap RingDK296-4611 Fill PlugDK296-1147 Second GearDK296-47 & 47A12 Magnetic Drain PlugDK296-1248 Thrust WasherDK296-4813 Case PlugDK296-1349 Snap RingDK296-49141-2 Cam and ShaftDK296-1550 Third GearDK296-50 & 50A153-4 Cam and ShaftDK296-15513-4 Synchronizer AssemblyDK296-5116 Reverse Cam and ShaftDK296-16523-4 Synchronizer KeysDK296-52171-2 Shift ForkDK296-1753 Cluster GearDK296-53 & 53A183-4 Shift ForkDK296-1854 Needle BearingsDK296-5419 Reverse ForkDK296-1955 Needle Bearing RetainersDK296-5520 Set ScrewDK296-2056 Metallic Thrust WasherDK296-56211-2 Shift RailDK296-2157 Counter ShaftDK296-57223-4 Shift RailDK296-2258 Roll PinDK296-5823 Reverse Shift RailDK296-2359 Rear Reverse Idler GearDK296-5924 Detents (Round)DK296-2460 Reverse Idler Gear (Slider)DK296-6025 Detents (Hatchet Head)DK296-2561 Needle BearingDK296-6126 Bolt (Side Detent)DK296-2662 Needle Bearing RetainerDK296-6227 Interlock PinDK296-2763 Metallic Thrust WasherDK296-6328 Detent Spring (Short)DK296-2864 Reverse Counter ShaftDK296-6429 Detent Spring (Long)DK296-2965 TailhousingDK296-6530 Top CoverDK296-3066 Air VentDK296-6631 Top Cover GasketDK296-3167 BushingDK296-6732 Bolt (Top Cover)DK296-3268 SealDK296-6833O-RingDK296-3369 GasketDK296-6934 MainshaftDK296-34C & 34E70 Bolts (Tailhousing)DK296-7035 Snap RingDK296-3571 Lock WashersDK296-7136 Steel BallDK296-36 ContentsDKT Maincase.

3 1 DKT Tailhousing .. 1 Rebuild Kits .. 2 SKF Main Bearings .. 3 Bearing Retainers .. 3 Synchronizer Assemblies .. 3 Close Ratio Gears .. 3 Wide Ratio Gears .. 4 Mainshafts .. 4 Counter Shafts .. 4 Bushings .. 5 Reverse Gear .. 5 Speedometer Gears .. 5 Shift Forks .. 5 Shift Rail Kit .. 6 Top Cover .. 6 Transmission Mounts .. 6 Top Cover .. 6 Plastic Plugs .. 6 Bolts .. 7 Seals .. 7 Transmission Yokes .. 7 Shift Cam and Shafts .. 7 Blocker Rings .. 7 Snap Ring .. 7 Apparel .. 8 Cobra Shifters .. 8 Hurst Competition Plus Shifters .. 8 Bellhousings .. 9 McLeod Street/Dual Performance Clutches .. 9 Clutch Forks .. 10 Pilot Bushings .. 10 Throwout Bearings .. 10 Third Members .. 11 Payment and Shipping Information .. 12To order a new transmission, or to have your transmission rebuilt, please contact TAILHOUSINGWe have manufactured a new aluminum tailhousing that replaces C4D, C4Z, C6O, and C7O casting numbers and has the correct shifter locations for:1964-65 Falcon1964-73 Mustang, Cougar1966-68 Fairlane, Cyclone, Ranchero, Torino 289, 302, 3901966-69 Falcon 289, 3021966-69 Mustang, Cougar 3901967 up Fairlane, Cyclone 427, 4281968-69 Mustang 428, 429 This will allow you to use your Toploader in different model vehicles without having to find a different tailhousing to movethe shifter to the right location.

4 Our tailhousing is available in 28 or 31 spline output shaft size.. DK296-65 AOur new aluminum wide bolt pattern maincase will be available soon. Every case will have a drain plug hole. To pre-ordera maincase, please contact us .. DK296-10 ADKT MAINCASEDKT TAILHOUSINGSMALL PARTS KITSEAL AND GASKET KITSMALL REBUILD KITROAD RACE KIT PLUSROAD RACE KITMASTER REBUILD KIT PLUSMASTER REBUILD KITREBUILD KITSMASTER REBUILD KITThis kit contains everything in the Master Rebuild Kit, plus assembly lube and cast blast paint. Can onlybe shipped by ground service. Please specify shaft sizes when RACE KITThis kit contains all needle bearings, snap rings, thrust washers, spacers, speedometer ball, dowel pins,case plug, shift lever o-rings, front and rear seal, gasket set, C springs, new magnetic drain plug, airvent, 3 shift rail set screws, counter shaft, 4 bronze original equipment blocker rings, Max type SKF front& rear main bearings, synchronizer keys and tailshaft bushing.

5 Please specify shaft sizes when rebuild kit with standard duty SKF bearings used to rebuild any 4 speed toploader . Available inany shaft size configuration. Kit contains: all needle bearings, snap rings, thrust washers, spacers,speedometer ball, dowel pins, case plug, shift lever o-rings, front and rear seal, gasket set, C springs,new magnetic drain plug, air vent, counter shaft, 4 bronze original equipment blocker rings, front & rearmain bearings, synchronizer keys, tailshaft bushing and instructions. Please specify shaft sizes whenordering ..DK296M-STDREBUILD KITSAll of our kits are professionally packed and ready for immediate delivery. We also offer our Top Cover to all kit purchasers foran additional $10 (a $ value).MASTER REBUILD KIT PLUSROAD RACE KIT PLUSThis kit contains everything in the Road Race Kit, plus assembly lube and cast blast paint. Can only beshipped by ground service. Please specify shaft sizes when ordering.

6 DK296MP-MAX2 SMALL REBUILD KITThis kit contains all needle bearings, snap rings, thrust washers, spacers, speedometer ball, dowel pins,case plug, shift lever o-rings, front and rear seal, gasket set and synchronizer C-springs. Please specifyshaft sizes when AND GASKET KITThis kit contains all gaskets, front and rear seal, three shift lever o-rings, rear bushing and case specify shaft sizes when ordering..DK296 SKSMALL PARTS KITThis kit includes all needle bearings, snap rings, thrust washers, spacers, speedometer ball, dowelpins.. RATIO GEARSCLOSE RATIO GEARSF irst Gear 32 Tooth ..DK296-41 Second Gear 28 Tooth ..DK296-47 Third Gear 25 Tooth ..DK296-50 Cluster Gear 1-1/16" One Piece Small Input ..DK296-5 This is our new 1 1/16 inch close ratio 4th gear. Use this gear as a direct replacement forany small input close ratio Toploader . This input is one piece just like the Gear 1 3/8 One Piece Big Input ..DK296-5 AThis is our new 1 3/8 inch close ratio 4th gear.

7 Use this gear to convert any closeratio Toploader to a large input unit or use it as a direct replacement for any largeinput close ratio Toploader . This input is one piece just like the ASSEMBLIESBEARING RETAINERSSKF MAIN BEARINGSSKF MAIN BEARINGSS tandard Duty Input Bearing ..DK296-6 Standard Duty Output Bearing ..DK296-38 BEARING RETAINERSNew seal and gasket included. Order 4 11/16"for 1964 4 hole cases and 4 7/8" for 1965-73 8hole ..DK296-1 New seal and gasket included. Order 4 11/16"for 1964 4 hole cases and 4 7/8" for 1965-73 8hole ASSEMBLIEST orque lock design. Inner and outer hubs are a matched set with new dogs and C-springs. Also available withbronze rings for an additional $ Design Synchronizer C-Spring ..DK296-441-2 Synchronizer Key ..DK296-433-4 Synchronizer Key ..DK296-5231-3/8 ..DK296-1 AMax Duty Input Bearing ..DK296-6 AMax Duty Output Bearing ..DK296-38 AClose Ratio Gear Set, Small Input.

8 DK296-CGSAI ncludes: 2nd, 3rd, 1 1/16 inch input shaft and cluster gear. Use this gear set to replace a worn gear set or convert a wideratio to a small input close ratio Ratio Gear Set, Big Input ..DK296-CGSI ncludes: 2nd, 3rd, 1 3/8 inch input shaft and cluster gear. Use this gear set to replace a worn gear set or convert a wideratio to a big input close ratio RATIO GEARSWIDE RATIO GEARSF irst Gear 32 Tooth ..DK296-41 Second Gear 31 Tooth ..DK296-47 AThird Gear 25 Tooth ..DK296-50 ACluster Gear 1-1/16" One Piece Small Input ..DK296-5 BThis is our new 1 1/16 inch wide ratio 4th gear. Use this gear as a direct replacement forany small input wide ratio Toploader . This input is one piece just like the Gear 1 3/8 One Piece Big Input ..DK296-5 CThis is our new 1 3/8 inch wide ratio 4th gear. Use this gear to convert any wide ratiotoploader to a large input unit. This input is one piece just like the " x 28 spline.

9 DK296-34C24" x 31 spline ..DK296-34E27" x 31 spline Torino, big block " x 28 spline small block Galaxie, 289 Cobra ..Call25-1/2" x 28 spline Sunbeam Tiger ..CallFits all small block Mustang, Cougar, Fairlane, Falcon, Comet, Ranchero, Boss 302 and Shelby GT 350 Toploaders. This isour own design mainshaft with OEM type oiling all big block Mustang, Cougar, Fairlane, GT 500 and 427 Cobra Toploaders. This is our own design mainshaft with OEMtype oiling passages and larger outside diameter from the back of the rear bearing to the output is the counter shaft that goes through the main cluster gear. Also known as lay Gear Counter Shaft ..DK296-57 Reverse Counter Shaft ..DK296-64 This is the counter shaft that goes through the reverse cluster gear. Also known as lay SHAFTSCOUNTER SHAFTSWide Ratio Gear Set, Small Input ..DK296-WGSAI ncludes: 2nd, 3rd, 1 1/16 inch input shaft and cluster gear. Use this gear set to replace a worn gear set or convert a closeratio to a small input wide ratio Ratio Gear Set, Big Input.

10 DK296-WGSI ncludes: 2nd, 3rd, 1 3/8 inch input shaft and cluster gear. Use this gear set to replace a worn gear set or convert a closeratio to a big input wide ratio Shift Fork ..DK296-17 Fits all 64-73 toploadersReverse Shift Fork ..DK296-19 SHIFT FORKSSHIFT FORKS3-4 Shift Fork ..DK296-18 Fits all 64-73 toploadersBlack 7 Tooth Speedometer Drive Gear ..C4DZ-17285 AUsed for Galaxie, Sunbeam Tiger and 64 Fairlane16 Tooth Driven Gear, RH ..16TR17 Tooth Driven Gear, RH ..17TR18 Tooth Driven Gear, RH ..18TR19 Tooth Driven Gear, RH ..19TR20 Tooth Driven Gear, RH ..20TR21 Tooth Driven Gear, RH ..21 TRSPEEDOMETER GEARSSPEEDOMETER GEARSPink 6 Tooth Speedometer Drive Gear ..C5ZZ-17285 AGreen 6 Tooth Speedometer Drive Gear ..DK296-GSGREVERSE GEARSREVERSE GEARSThis is the straight cut gear that slides forward to engage Spur Gear ..DK296-605 BUSHINGSBUSHINGS28 Spline Tailhousing Spline Tailhousing Bushing ..DK296-67 AYellow 7 Tooth Speedometer Drive Gear.