TM-1 AUTO LUBRICATOR 35477 - lubesystemsonline.com

1 35477 R0 02/081TM-1 LubricatorAutomatic CyclicApplicationTM-1 Lubricators are used with single line resistance type centralized lubricating systems. These systems utilize cyclic delivery meter units to proportion oil discharged from the is a motor-driven, spring discharge piston pump. The motor incorporates a gear reduction which determines the operating cycle time of the pump piston. Available cycle times are shown in the table Time - 115 VAC50 Hz60 Hz145 min120 min72 min60 min15 minTechnical DataReservoir Capacity1 pint (475 cc)1 literLubricator Inlet Filter40 micron particle separationDischarge Pressure20-50 psiFactory Discharge Volume Per Cycle* to adjustableViscosity range150 to 8,000 SSU (35-1750 cSt)

2 At operating temperatureNotes Regarding UseLubricator inlet fi lter should be inspected periodically and cleaned/replaced as Discharge pressure will decrease as the number of meter units in the system *Discharge Volume Per CycleTo reduce oil delivery, remove lock screw, measure A , turn adjusting screw clockwise, increasing A by B dimension, as shown on !,OCK SCREW!DJUSTING SCREW Cycle Time - 230 VAC50 Hz60 Hz145 min120 min72 min60 min15 min9 minCycle Time - 115/230 VAC2 minCycle Time - 110/120 VAC6 min5 min35477 R0 02/082 Distribution SystemUses Type F meter units. For system ( ) limitations, see Bijur Engineering Manual. For system fl ow value ( T) limitations, refer to table Units (#)Discharge Per Cycle (cc).

3 75115 MotorContinuous duty, single phase, synchronous induction timing motor for 50/60 Hz single voltage 115 and 230 VAC and dual voltage for 115/230 VAC. Power consumption is 3 for Dual Voltage Motor115 VACC onnect yellow and red, insulate VACC onnect yellow and black, insulate Level SwitchModels of this LUBRICATOR equipped with liquid level switch are listed in the How to Order chart on page 3. They are supplied so the switch will close an electrical circuit whenever the oil in the reservoir is above the minimum operating level. Thus, when connected to a light or other indicating device, the liquid level can be may reverse the operation when desired, by inverting the fl oat.

4 When the fl oat is reversed, the switch will close an electrical circuit whenever the oil level is below the minimum operating : The low level switch is intended to be a reservoir low level indication device, and thus is not intended to be wired in series with the motor. Switch contact rating is 10 watts maximum (light or indicating device is not supplied by Bijur Delimon).VoltsAmpsACDC0 ReplacementA fi lter at pump inlet protects the lubricating system. The felt fi lter disc should be inspected every six months. If not clean, replace. To remove fi lter, pry fi lter cup loose in several places with a screwdriver. Remove screens and felt fi lter disc. Insert new fi lter disc in cup, then screens, so that course screen in next to pump body when installed.

5 Reinstall assembly, making sure that it is tight and that the tip of the fi lter cup is about 1/16 from the shoulder on pump as reserves the right to change motor size, mounting dimensions and/or R0 02/083 How To OrderVoltsCycle TimeTM-1 with 1 Pint ReservoirTM-1 with 1 Liter ReservoirMotor & Gear Boxw/ Level SwitchNo Level Switchw/ Level SwitchNo Level Switch50 Hz60 HzPart #Part #Part #Part #Part #115 VAC145 min120 minC2889C2731D3087D310719422-272 min60 minC2890C2739D3089D310819422-315 minC2896C2803D3095D311519422-1230 VAC145 min120 minC2892C2763D3091D311024095-272 min60 minC2893C2764D3092D311124095-315 minC2894C2765D3093D311224095-19 minC2897C2774D3096D311324095-1115/230 VAC2 minC2895C2798D3094D311423086110/120 VAC6 min5 min------20439---19422-5 When ordering, specify LUBRICATOR type and part number.

6 Such as: TM-1 LUBRICATOR , Part # PartsOrder by part number and name show in table. Include complete LUBRICATOR part number and serial letters as shown on nameplate. Example: S178 fi lter group for LUBRICATOR C2731, Serial ?. For major repairs requiring parts not identifi ed on the drawing, return the LUBRICATOR for factory rebuilding and adjustment. If a new LUBRICATOR is required for replacement, order by part number and serial letters shown on the #Description1 VariousElectric Motor, 100/120 V2B3108 Thru Coupling3B8197 Reservoir Gasket4B8807 Float Switch Assembly (1 pint)B7760 Float Switch Assembly (1 liter)5H0402O-ring (Float Switch)6HS195 Screw, Cover Mounting (x4)7B7827 Motor Housing8B9230 Fill Cap9S178 Filter Group10B7824 Bevel Gear10aHS209 Set Screw, Bevel Gear11B7823 Bevel Gear11aHS210 Set Screw, Bevel Gear12B3344 Outlet Check Valve12aA3844 Outlet Valve Gasket # M!

7 " P$ ! !P "( "P%&' " P # $ %13B4359 Inlet Check Valve13aA4191 Inlet Valve Gasket14D3086C-KITR eservoir, Plastic (1 pint)D3218 Reservoir, Plastic (1 liter)15B7389 Nut16B7378 Pump Assembly (1 pint)B8827 Pump Assembly (1 liter) 35477 R0 02/084 Dimensional SchematicsTM-1 with 1 Pint ReservoirTM-1 with 1 Liter ReservoirMeasurements shown in inches (mm).# $ # " " & ( " '& (' " " & ( % " $$ & $ " !& ' 8=BC0=C 5443 1 DCC>= & %# ! <C6 7>;4B 5>A # 1>;CB # # (' !# ( ' # % " "' '$ ' 6A>D=3 C4A<8=0;58;;4A 20?38B270A64 E>;D<4 039 DBC<4=C ! =?C 2>=3D8C 2>==42C8>=>DC;4C $ % !# D=5 C7A403 5>A $ "! > 3 CD18=6 2>==42C8>= DB4 2> <?A4BB8>= =DC 1 ($ 2> <?)))))))

8 A4BB8>= B;44E4 1 % ;8@D83 ;4E4; BF8C27 ;403B ! ' 60D64 BCA0=343<>C>A ;403B ! 60D64 ! 5>A B8=6;4 E>;C064 <>C>A " 5>A 3D0; E>;C064 <>C>A % 8=274B ;>=6 " & ( 380 <C6 7>;4B ! ?; % "&$ % ( $ &$ #% 8=BC0=C 5443 1 DCC>=>DC;4C $ % !# 189DA C0??43 7>;45>A $ "! > 3 CD18=6 2>==42C8>=& ' 380 7>;4 5>A ! =?C 2>=3D8C 2>==42C8>= ;4E4; BF8C27;403B ' 60 " & ( " & ( % %& %( # & %# (# &$ ## # $( $ # &$ ! % ' # $ ?0AC =D<14 ABC0<?43 74A4<>C>A ;403B!! 60 & >=658;; 20?)))))))