Example: marketing
Torque Range - Snap-on
Torque Range 3 Torque Range 2 TORQUE Measuring & Testing Change between ft-lbs, in-lbs and N•m with the touch of a button High strength sealed reversible ratchet Rugged, shock resistant housing
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
TORQUE MULTIPLIERS - Snap-on Incorporated
www1.snapon.commodels of torque multipliers, ranging from the YA290PLUS, with a rated capacity of 750 lb. ft. and a gear ratio 4.0:1, to the YA395, with a ... Input Drive Female Sq., in. 1/2 1/2 1/2 1/2 3/4 1/2 1/2 1/2 Output Drive Male Sq., in. 3/4 3/4 3/4 1 1 1 1-1/2 1-1/2 Bearings — — Needle Needle — Needle Needle Needle
Tips on Proper Torque Wrench Use and Maintenance-12-22 …
www1.snapon.comA torque wrench is a precision instrument designed to apply a specific amount of force to a fastener. Whether tightening head bolts on an automobile engine, lugs for tire and rim installation or inspecting fastener tolerances on high-performance equipment, it is extremely important that proper care is used. ...
Global OBD Vehicle Communication Software Manual
www1.snapon.comiii Safety Information For your own safety and the safety of others, and to prevent damage to the equipment and vehicles upon which it is used, it is important that the accompanying Important Safety Instructions be read and understood by all persons operating, or coming into contact with, the equipment.
Snap-on Diagnostics Repair Guide
www1.snapon.comRepair Service - 180 Days . The repair center warranty covers the repair flat rate level from the qualifying repair. If a product is sent back into the repair center within 180 days and found to require additional repair(s) at the same or lower level it will be covered under this warranty.
OECD Due Diligence Guidance for Responsible …
www1.snapon.comOECD Due Diligence Guidance for Responsible Supply Chains of Minerals from Conflict-Affected and High-Risk Areas ISBN 978-92-64-1111-89 20 2011 06 1 P-:HSTCQE=VVVV]^: OECD Due Diligence Guidance for Responsible Supply Chains of Minerals from Confl ict-Affected and High-Risk Areas
User Manual - Snap-on Incorporated
www1.snapon.comThis manual contains instructions for using the Vantage PRO unit. Some of the illustrations shown in this manual may cont ain options that are not included on your system.
Volkswagen/Audi Vehicle Communication Software Manual
www1.snapon.comVolkswagen/Audi Vehicle Communication Software Manual August 2013 EAZ0031B01E Rev. A. ii Trademarks ... Engine ID codes are stamped on the engine block in three-digit alpha characters followed by a series of numbers (usually six), for example, “AEG 029452". If …
0012012 - Snap-on Incorporated
www1.snapon.com• How-to-Guide for Diesel Particulate Filters (DPF) system components, fundamentals of technology, regeneration instruction • An Electronic Parking Assistance class including diagnostic tips
User Manual - snapon.com
www1.snapon.com1 Chapter 1 Using This Manual This manual contains tool usage instructions. Some of the illustrations shown in this manual may contain modules and op tional equipment that
GENERAL REQUIREMENTS FOR CORRUGATED BOXES
www1.snapon.comGENERAL REQUIREMENTS FOR CORRUGATED BOXES CS19.0.5 Issued: 2017AUG10 CORPORATE STANDARD File No. 19-0 Revision A: 2017AUG10 The information contained in this document is confidential and the sole property of Snap-on Incorporated, and may not be
Related documents
Useful Motor/Torque Equations for EML2322L
mae.ufl.eduCalculate the Torque required to lift the Force with the lever arm . T = F x d = 49.05 N x 0.5 m = 24.525 N-m . We cannot perform the lift with this set-up, because the stall torque is smaller than . the torque required for the lift. We must either shorten the length of the lever arm,
Torque Torque and Rotational Inertia - Boston University
physics.bu.eduTorque and Rotational Inertia 2 Torque Torque is the rotational equivalence of force. So, a net torque will cause an object to rotate with an angular acceleration. Because all rotational motions have an axis of rotation, a torque must be defined about a rotational axis. A torque is a force applied to a point on an object about the axis of rotation.
Rotation: Moment of Inertia and Torque - Waterloo Maple
www.maplesoft.comTorque and Newton's Second Law for Rotation Torque, also known as the moment of force, is the rotational analog of force. This word originates from the Latin word torquere meaning "to twist". In the same way that a force is necessary to change a particle or object's state of motion, a torque is necessary to change
AERA Torque Specs
www.aera.orgMake Liter CID Engine Model Year Rod Torque Main Torque Cylinder Head Bolt Torque ACURA 1.6 97 D16A1 86-89 23 FT/LBS 40 FT/LBS 22, 47 FT/LBS ACURA 1.7 104 B17A1 92-93 14,23 FT/LBS 56 FT/LBS 22,61 FT/LBS
General Information on Torque Specifications
www.antiseize.comTorque values may also have to be reduced when the fastener is threaded into aluminum or brass. The specific torque value should be determined based on the aluminum or brass material strength, fastener size, length of thread engagement, etc. The standard method of verifying torque shall be performed by marking a line on the fastener (head or ...
Harmonic Balancer Torque Specs - Parts Highway
www.partshighway.comHarmonic Balancer Torque Specs Dorman # Applications Torque Spec 594-001 1990-88 3.8L (231) Buick, Chevrolet, Oldsmobile, Pontiac 219 lbs 594-002 1996-69 5.7L (350) Chevrolet, GMC Truck 75 lbs 594-003 1990-88 3.8L (231) Buick, Chevrolet, Oldsmobile, Pontiac 219 lbs 594-004 2000-95 3.8L (231) Buick, Chevrolet, Oldsmobile, Pontiac 110 lbs 594-005 1992-91 3.8L (231) …
Bolt Tightening - Tohnichi | Your Torque Partner
www.tohnichi.comTightening torque is not influenced by the bolt length so easy to standardize. The Bolt efficiency will be low due to wide tolerance of the tension. Rotation angle method The tightening is managed by rotting angle which start from the seating point of the bolt head.
TORQUE-TENSION REFERENCE GUIDE - Fastenal
www.fastenal.comTORQUE-TENSION REFERENCE GUIDE Printed in U.S.A. • Supply Part Number: 9702365 • AS 06/14 Torque Poster For additional technical information, contact Fastenal Engineering at engineer@fastenal.com. Nominal Dia. (in.) Threads per inch 307A ASTM A307 Grade A SAE J429 Grade 5 SAE J429 Grade 8 F N L G 9 FNL Grade 9 Clamp Load (Lbs.) Tightening ...