TruBolt - ramset.com.au

1 NEW ZEALAND0800 RAMSET (726738) 780 Xtrem Ramset TruBolt Xtrem Advantages:A seismic certified heavy duty, torque controlled expansion anchor for permanent anchoring into concrete. Certified for seismic C1 & C2 applications refer report number ETA-15/0893 Assessed as per ETA001 Annex E Certified Seismic C1 & C2. Certified Option 1 Cracked Concrete. TR020 Fire tested - Fire rated performance up to 2 hours. Highest Performance in floor, wall & overhead applications. ETA CERTIFIED FOR SEISMIC AND CRACKEDCONCRETEC ertificationApproval Number / ReportEuropean Technical Assessement (ETA) to ETAG 001 Part 1, Option 1 ETA - 15/0893 European Technical Assessment (ETA) ETAG 001 Part 1, Annex E, C1 & C2 ETA - 15/0893 ApprovalsPREMIUM ANCHORINGS eismicCracked concreteDrinking water safeSA TS101:2015 TestedSeismicCracked concreteDrinking water safeSA TS101:2015 TestedSeismicCracked concreteDrinking water safeSA TS101.

2 2015 TestedPREMIUM ANCHORINGS ubstrates Concrete Applications All steel constuctions Facades Curtain wall Staircases Ladders Guide railings Stadium seatingTruBolt Xtrem A seismic certified heavy duty, torque controlled expansionanchor, for permanent anchoring into Xtrem Stud Anchor - Hex Nut - Zinc PlatedPart NumberDescriptionThread DiameterTotal anchor length (mm)Maximium fixture thickness (mm)Drilling Diameter (mm)Minimum hole depth (mm)Maximum tightening torque (Nm)Fixture clearence hole diameter (mm)Pack QtyT08075 XTruBolt Xtrem M8x75/15M8751586020Nm9100T08090 XTruBolt Xtrem M8x90/30M8903086020Nm950T08120 XTruBolt Xtrem M8x120/60M81206086020Nm950T10085 XTruBolt Xtrem M10x85/5M10855108045Nm1250T10100 XTruBolt Xtrem M10x100/20M1010020108045Nm1225T10120 XTruBolt Xtrem M10x120/40M1012040108045Nm1225T10140 XTruBolt Xtrem M10x140/60M1014060108045Nm1225T12105 XTruBolt Xtrem M12x105/10M1210510129560Nm1425T12115 XTruBolt Xtrem M12x115/20M1211520129560Nm1425T12135 XTruBolt Xtrem M12x135/40M1213540129560Nm1425T12180 XTruBolt Xtrem M12x180/85M1218085129560Nm1420T16145 XTruBolt Xtrem M16x145/25M161452516120110Nm1810T16170 XTruBolt Xtrem M16x170/50M161705016120110Nm1810T20170 XTruBolt Xtrem

3 M20x170/30M201703020140160Nm2210T20200 XTruBolt Xtrem M20x200/60M202006020140160Nm2210 Installation1. Drill or core a hole to the recommended diameter (same as the TruBolt ) and depth using the fixture as a template. Clean the hole thoroughly with a hole cleaning brush. Remove the debris with a hand pump, compressed air, or Insert the anchor through the fixture and drive with a hammer until the washer contacts the Tighten the nut with a torque wrench to the specified assembly Specification Bolt: Cold formed carbon steel, M8: Zinc Electroplated (>5 m)EN 1SO 4042:1999, M10-M20: Zinc Electroplated (>5 m) + Anti-friction coating Clip: M8 Stainless Steel, M10-M20 Carbon Steel, Zinc Electroplated (>5 m) EN 1SO 4042:1999 Nut: Steel strength grade 8 DIN267 or ISO 898-2:2012 M8-M10 Zinc Electroplated (>5 m) EN 1SO 4042:1999.

4 M12-M20 Zinc Electroplated (>5 m) + Anti-friction coating Washer: M8 NF E 25514 Zinc Electroplated (>5 m) EN 1SO 4042:1999. M10 - M20 EN 10025:2004 or EN10088- 2:2005, Zinc Electroplated (>5 m) + Anti-friction coatingramsetreid 1 Ramset Drive, Chirnside Park 3116 In the interests of product improvement, ramsetreid reserves the right to alter product specifications as required. Information included in this resource book is correct at time of printing. It is the responsibility of the user to ensure product selected is appropriate for its intended use. For further technical information go to or contact Ramset on the numbers indicated. ITW Australia Pty. Ltd. ABN 63 004 235 063 trading as ramsetreid Copyright 2016 Trademarks of Cetram Pty.

5 Ltd. used under license by ramsetreid