Ultra Rib I 2007 - metal wall and roof

1 Ultra -Rib I. INDUSTRIAL-COMMERCIAL SIDING Effective September 2007. 38" OVERALL. 36" COVERAGE. 12" 1 1/2". GRAVITY LOAD TABLE (STEEL) (psf). MATERIAL AND metal . Ga. Spans 4'-0 5'-0 6'-0 7'-0 8'-0 9'-0 10'-0 . THICKNESS PLAIN PAINTED SPECIFICATION FINISH. GALVANIZED Grade 50 (50 ksi plain: regular 1 100 64 45 33 25 20 NR. STEEL yield strength), spangle 26 2 78 50 35 26 20 NR NR. 26 ga. lb. lb. Grade 80 (80 ksi painted: two-coat 3 98 63 44 32 25 NR NR. 24 ga. lb. lb. yield strength) for 70% Kynar 500/.

2 22 ga. lb. lb. 26 ga. structural Hylar 5000; 1 128 82 57 42 32 25 NR. 20 ga. lb. lb. steel with G90 siliconized 24 2 106 68 47 35 27 21 NR. coating, both polyester; vinyl conforming to plastisol; mil 3 133 85 59 43 33 26 NR. ASTM A 653 two-coat polyester 1 159 102 71 52 40 31 25. backer (26 ga. 22 2 142 91 63 46 35 28 23. panels have Super . Alurite paint only) 3 177 114 79 58 44 35 28. ALUMINUM-ZINC Grade 50 (50 ksi plain: regular 1 190 122 85 62 48 38 30. ALLOY COATED yield strength) , spangle STEEL Grade 80 (80 ksi painted: two-coat 20 2 176 112 78 57 44 35 28.)

3 26 ga. lb. lb. yield strength) for 70% Kynar 500/ 3 219 140 98 72 55 43 35.. 24 ga. lb. lb. 26 ga. structural Hylar 5000;. 22 ga. lb. lb. steel with AZ55 siliconized GRAVITY LOAD TABLE (ALUMINUM) (psf). 20 ga. lb. lb. coating (for plain) polyester; vinyl or AZ50 coating plastisol; mil Thk. Spans 4'-0 5'-0 6'-0 7'-0 8'-0 9'-0 10'-0 . (for painted), both two-coat polyester 1 172 110 77 56 43 34 NR. conforming to backer (26 ga..032 2 97 62 43 32 24 NR NR. ASTM A 792 panels have Super . Alurite paint only) 3 121 78 54 40 30 24 NR.

4 ALUMINUM 3004-H36 or plain: mill finish 1 242 155 108 79 61 48 39..032" lb. lb. equivalent (28 ksi painted: two-coat .040" lb. lb. yield strength).. 70% Kynar 500/ .040 2 133 85 59 43 33 26 21..050" lb. lb. aluminum alloy Hylar 5000; 3 166 107 74 54 42 33 27. conforming to siliconized 1 347 22 154 113 87 68 55. ASTM B 209 polyester; vinyl plastisol; mil .050 2 178 114 79 58 44 35 28. two-coat polyester 3 222 142 99 73 56 44 36. backer NOTES: 1. The allowable loads are based on 1986 AISI and 1986. Jackson, GA (800) 884-4484 Aluminum Association specifications.

5 Grapevine, TX (800) 477-9066 2. The allowable loads are based on stress only. Salem, OR (800) 477-8028 3. Ultra -Rib I panels are to be used for siding only. Headquarters - Lancaster, PA (800) 477-2741. 2007 FABRAL. Ultra -RIB I SPECIFICATIONS. PART I GENERAL C. Finish: Refer to manufacturer's standard color card to determine appropriate finish and SUMMARY color. All panels shall receive a factory-applied exterior coating (siliconized polyester). A. Section includes: Prefinished, prefabricated , structural exposed fastener wall system (Kynar 500/Hylar 5000*) (vinyl plastisol) (26 ga.)

6 Panels will have Super Alurite paint). and accessories. conforming to the following: B. Related Sections: 1. metal preparation: all metal shall have the surfaces carefully prepared for 1. metal decking painting on a continuous process coil coating line by alkali cleaning, hot water 2. Rough carpentry, plywood, and underlayment rinsing, application of chemical conversion coating, cold water rinsing, sealing 3. Insulation with an acid rinse, and thorough drying. 4. Membrane roofing 2. Prime coating: a base coat of epoxy paint, specifically formulated to interact with 5.

7 Flashing and sheet metal the top-coat, shall be applied to the prepared surfaces by roll coating to a dry 6. Joint sealers: sealants and caulk film thickness of mils. This prime coat shall be oven cured prior to 7. Structural framing. application of finish coat. REFERENCES 3. Exterior coating: a finish coating (from above) shall be applied over the primer A. American Society for Testing and Materials (ASTM) by roll coating to a dry film thickness of mils ( mils for 1. ASTM A 653: Steel Sheet, Zinc-Coated by the Hot Dip Process vinyl plastisol) for a total dry film thickness of ( mils for 2.)

8 ASTM A 792: Steel Sheet, Aluminum-Zinc Alloy Coated by the Hot Dip Process. vinyl plastisol). This finish coating shall be oven-cured. 3. ASTM B 209: Aluminum and Aluminum Alloy Sheet and Plate. 4. Interior coating: a washcoat shall be applied on the reverse side over the primer B. Sheet metal and Air Condition Contractors National Association, Inc. (SMACNA) by roll coating to a dry film thickness of mils for a total dry film 1. SMACNA Architectural Sheet metal Manual, 1993 Edition. thickness of mils.

9 The washcoat shall be oven-cured. C. American Iron and Steel Institute (AISI) 5. Color: the color of the exterior finish shall be as chosen from the manufacturer's 1. AISI Cold Formed Steel Design Manual standard color chart. D. Aluminum Association 6. Physical properties: the coating shall conform to the manufacturer's standard 1. Aluminum Design Manual performance criteria as listed by certified test reports for fade, chalk, abrasion, E. metal Construction Association (MCA) humidity, adhesion, pollution resistance, and others as required and standard 1.

10 Preformed metal Wall Guidelines within the industry. F. Code references ACCESSORIES. 1. ASCE, Minimum Loads for Buildings and Other Structures A. Flashing and Trim 2. BOCA National Building Code 1. All flashing and trim shall be of the same material, gauge, finish, and color as the 3. UBC Uniform Building Code wall panels and fabricated in accordance with standard SMACNA procedure and 4. SBC Standard Building Code details. SYSTEM DESCRIPTION 2. Fabricate gutters and downspouts in the same gauge, material, finish, and color A.