UNIVERSAL INSTRUCTIONS BRACED OVAL POOLS

1 UNIVERSAL INSTRUCTIONSBRACED OVAL POOLSPLEASE READ THESE INSTRUCTIONS CAREFULLY AND THOROUGHLY BEFORE ST ART ING GROUND PREPARAT ION AND POOL SO WILL PREVENT Pool: General informaition -----------------------------------1) Selection pool site ---------------------------------------- -------2) Ground preparation ---------------------------------------- ------3) Assembling side vertical,Horizontal support and brace- 4) Drawing pool shape ---------------------------------------- ------5) Connecting tension straps --------------------------------------6) Positioning assembled oval parts -----------------------------7) Assembling bottom rail ---------------------------------------- --8) Installing wall ---------------------------------------- ---------------9) Build an earth mound(Cove) -----------------------------------10)

2 Through the wall skimmer --------------------------------------11 ) Liner installation ---------------------------------------- -----------Please refer to "Assemble TopSeat , Vertical and Cover" of an attached ) Filling the pool ---------------------------------------- -------------13) Helpful information ---------------------------------------- -------14) SAFETY RULES ---------------------------------------- ---------- BRACED OVAL Parts List (#A OVAL CARTON) not start the installation of your pool unless you have an entire day to finish the not try to set up your pool on a windy wall will be difficult or even impossible to average pool needs 2 or 3 people for following tools and materials are PencilMasking TapeRakeChalk or FlourPlastic TapeEarth RollerStringHammer & NailsSand2"x4" BoardScrewdriverTamping ToolPegs and StakesCarpenter's LevelMeasuring TapePatio BlockOpen the cartons and remove all parts except steel wall and pool assembly , you must identify, count and check all parts for assembly by parts list.

3 Familiarize yourself with all of the parts. Refer to the parts ) The site must be large enough to accommodate the pool with plenty of area around it for pool accessaries, chairs, tables ) Determine where your filtration and skimmer will be located. It must be connected to a grounded 110 volt electrical outlet, with a (Ground Fault Interrupter)c) The pool must be in reach of your water supply. Although the water should not be drained, but kept clean through filtration and chemicals, there should be drainage facilities near in case of ) Perimeter area of ground must be absolutely level and firm. All grass and sod under entire pool area must be dug out to avoid unpleasant odors from decomposition under the pool due to lack of air.

4 Remove sharp objects, stones, twigs, pebbles, roots, etc. They may damage the liner. If the ground has been treated with chemicals or weed killer allow two weeks before setting up the pool. Do not set up the pool on concrete, asphalt, tar paper, peatmoss, sand, gravel, or where nut grass has been planted. Poorly prepared ground could allow certain weeds or grass to grow through the liner. Liner is not warranted against this. If ground is uneven in perimeter area, dig out the high spots. Do not build up the low side by padding it with weight and movement of the water will pack down the fill causing the pool to sink. Inside perimeter of pool (the area inside of the frame and wall) can be leveled with 1" or 2" of sand raked and rolled ) SELECTION OF POOL SITEB efore starting the installation, the following points are important;FAILURE TO OBSERVE ANY OF THE ABOVE INSTRUCTIONS WILL VOID INFORMATIONB efore attempting to set up the pool, read the entire INSTRUCTIONS .

5 There are certain areas in the INSTRUCTIONS that are extremely important to follow exactly as written and/or pictured. Any deviation from these INSTRUCTIONS voids warranty of the pool and could cause bodily harm or damage to your ' 7/8" (48" Wall)21' 7/8" (48" Wall)21' 6-1/8" (52" Wall)21' 6-1/8" (52" Wall)25x1530x15(9198mm)(7656mm)25' 1-3/8"(6422mm)15'(6422mm)(4572mm)15'(457 2mm)(6557mm)(6557mm)30' 2-1/8"SIFTED EARTH OR SAND NEEDEDPER EACH SIZE POOL AS FOLLOWS:CAUTION:16' x 12' 26 cubic feet ' x 12' 34 cubic feet ' x 12' 42 cubic feet ' x 15' 54 cubic feet ' x 15' 66 cubic feet ' x 18' 87 cubic feet ' x 21' 127 cubic feet SIZE Wall Length Top Sheetmmftin.

6 Q'ty1612 13,855 45 5 4/8 122012 16,364 53 8 2/8 142412 18,873 61 11 162515 20,625 67 8 143015 23,756 77 11 2/8 163318 26,586 87 2 6/8 184121 32,549 106 9 4/8 2224' 2-3/8" (48" Wall)24' 7-5/8" (52" Wall)a) Mark off your pool area by driving stakes. Have a helper hold a tape measure or a string and mark off the pool perimeter using flour or chalk.

7 Remove sod inside the pool area to a distance of 1 feet beyond dimensions shown in the plot layout around entire perimeter of preparation of the ground is the most important step in the installation of the ) Remove all grass from within the entire pool area. It is not enough to just cut the grass.

8 The sod must be ) Two or three inches of sand is the best for your liner. Using sand eliminates the necessity to level inside of frame area except where exceptionally high or low areas areas should either be dug or filled in. This does not mean the perimeter or frame area. That area must be firm and level by digging ) Do not fill low spots in the area where pool wall will rest. as setting may cause your pool to become out of level. Making sure pool bottom is is a ) If your site is not on firm soil, use 2" patio blocks for the base of the wall Care should be taken to center a patio block under each bottom plate. The top of the patio blocks should be flush with the prepared ground ) GROUND PREPARATION18' 1" (48" Wall)18' 1" (48" Wall)18' 1" (48" Wall)27' 3-3/8" (48" Wall)18' 6-2/8" (52" Wall)18' 6-2/8" (52" Wall)18' 6-2/8" (52" Wall)27' 8-5/8" (52" Wall)24x1233x1841x2120x1221'(6401mm)33' 2-1/8"(4847mm)15' 10-7/8"(6083mm)(7319mm)(12570mm)41' 2-7/8"(10112mm)19' 11-4/8"24' 1/8"(7374mm)11' 10-1/8"(5645mm)(3611mm)(8450mm)(5511mm)( 8314mm)(5511mm)(3611mm)11' 10-1/8"(5645mm)(5511mm)(5487mm)(5645mm)( 3611mm)(7510mm)11' 10-1/8"18'16x1223 Use #0104 PACK Oval frame bolt #0105(#0106)PACK Strap bolt )

9 ASSEMBLINGSIDE VERTICAL, HORIZONTAL SUPPORT AND " x 1/2" Truss Head Side Vertical For 48" Side Vertical For 52"The Figure which looked at attachment of Side Upper Joint from Sheet Metal ScrewResin Side Upper Joint (Packed #3 Package) Sheet Metal Brace For 48" Brace For 52"from inside, Do not fasten brace to side 1/4" nut from inside, Do not fastenWasher from outside then put M8 nut from insaide AND1/4"X1/2" truss head screw from outside thenWasher from outside then put M8 nutConnect side vertical to horizontal M8x20 hex head bolt with PlainPut M8x20 hex head bolt with PlainSTEP2;STEP1; NutSTEP253 1/8" (1348mm)55 3/4" (1414mm)52 3/8" (1331mm)49 1/8" (1248mm)53 7/8" (1367mm)49 3/4" (1264mm) Brace For 52" Brace For 48" Horizontal Support For 48" Horizontal Support For 52" Side Vertical For 52" Side Vertical For 48"4 Connect brase to horizontal from outside then put M8 nut Put M8x20 hex head bolt with Plainfrom inside, Do not fasten ; Fasten all bolts and screws hex head two sets each for sidevertical to horizontal support, brace to side verticaland brace to horizontal support.

10 #12X3/4 Sheet Metal Screw two sets each for bracetoside x 20 Hex Head BoltM8 x 20 Hex Head BoltM8 x 20 Hex Head NutM8 StrapPlain WasherPlain " x 1/2" Truss Head Horizontal Support For 48" Horizontal Support For 52"STEP3; 32335/8" Side Lower Rail Joint - For 1" & 6 " Side Lower Rail Joint - For All other Frame20mmM8 x 20 Hex Head ) ASSEMBLING TENSION ;5 Refer page-7 "5) Connecting tention straps."Attach End strap to Holizontal support, Putto determine kind of Nut from bottm. Put all bolt and tighten hex head Bolt from top and NutPlain #12x3/4 Sheet Metal Screw4) DRAWING POOL SHAPEP lease Draw a line with seeing the picture of each pool size.(618mm)2'3/8"(1806mm) 5'11-1/8"5' 7-5/8"(4847mm)16x12 5'11-1/8"2'3/8"(3611mm)(618mm)11' 10-1/8"(1236mm)(1717mm)15'10-7/8"(1806mm )4'5/8"(7319mm)24'1/8"(618mm)2'3/8"4'5/8 "(1236mm)4'5/8"(4232mm) 13' 10-5/8"(1236mm)12'2"(3708mm)(1806mm)5' 7-5/8" 5'11-1/8"(3611mm)11' 10-1/8" 5'11-1/8"(618mm)2'3/8"(1806mm)(1717mm)24 x12 7' 6"(765mm)2'6-1/8"(1530mm)(1530mm)5'1/4"5 '1/4"5'1/4"7' 1-5/8"30'1"(9170mm)(2174mm)(2286mm)15'2- 1/8"(765mm)2'6-1/8" 7' 6"(4572mm)15' (2286mm)(5317mm)(4626mm)30x15 17' 5-3/8"533'3/4"8' 8-3/8"(2650mm)(10076mm)33'3/4"(765mm)2'6 -1/8"(1530mm)5'1/4"(1530mm)5'1/4"(4626mm )15'2-2/8"(2744mm) 9'(765mm)2'6-1/8"(5487mm) (2744mm)18' 9'33x18 20' 7/8"(6119mm)(4631mm)