User Manual ADAM-6000 Series - Advantech

1 user ManualADAM- 6000 SeriesEthernet-based Data Acquisition and Control ModulesADAM- 6000 user ManualiiCopyrightThe documentation and the software included with this product are copyrighted 2018by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the rightto make improvements in the products described in this Manual at any time withoutnotice. No part of this Manual may be reproduced, copied, translated or transmittedin any form or by any means without the prior written permission of Advantech Co.,Ltd. Information provided in this Manual is intended to be accurate and reliable. How-ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-ments of the rights of third parties, which may result from its and Pentium are trademarks of Intel Windows and MS-DOS are registered trademarks of Microsoft other product names or trademarks are properties of their respective WarrantyAdvantech warrants to you, the original purchaser, that each of its products will befree from defects in materials and workmanship for two years from the date of pur-chase.

2 This warranty does not apply to any products which have been repaired or altered bypersons other than repair personnel authorized by Advantech , or which have beensubject to misuse, abuse, accident or improper installation. Advantech assumes noliability under the terms of this warranty as a consequence of such of Advantech s high quality-control standards and rigorous testing, most ofour customers never need to use our repair service. If an Advantech product is defec-tive, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials,service time and freight. Please consult your dealer for more you think you have a defective product, follow these all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem your dealer and describe the problem.

3 Please have your Manual , product, and any helpful information readily your product is diagnosed as defective, obtain an RMA (return merchandize authorization) number from your dealer. This allows us to process your return more pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty the RMA number visibly on the outside of the package and ship it prepaid to your No. 2003600003 Edition 9 Printed in TaiwanAugust 2018iiiADAM- 6000 user Manual Declaration of ConformityCEThis product has passed the CE test for environmental specifications when shieldedcables are used for external wiring. We recommend the use of shielded cables. Thiskind of cable is available from Advantech . Please contact your local supplier forordering Class ANote: This equipment has been tested and found to comply with the limits for a ClassA digital device, pursuant to part 15 of the FCC Rules.

4 These limits are designed toprovide reasonable protection against harmful interference when the equipment isoperated in a commercial environment. This equipment generates, uses, and canradiate radio frequency energy and, if not installed and used in accordance with theinstruction Manual , may cause harmful interference to radio communications. Opera-tion of this equipment in a residential area is likely to cause harmful interference inwhich case the user will be required to correct the interference at his own Support and the Advantech web site at where you can find the latest information about the your distributor, sales representative, or Advantech 's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: Product name and serial number Description of your peripheral attachments Description of your software (operating system, version, application software, etc.) A complete description of the problem The exact wording of any error messagesADAM- 6000 user ManualivSafety these safety instructions this user Manual for later this equipment from any AC outlet before cleaning.

5 Use a damp cloth. Do not use liquid or spray detergents for plug-in equipment, the power outlet socket must be located near the equip-ment and must be easily this equipment away from this equipment on a reliable surface during installation. Dropping it or letting it fall may cause openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE sure the voltage of the power source is correct before connecting the equipment to the power the power cord so that people cannot step on it. Do not place anything over the power cautions and warnings on the equipment should be the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient pour any liquid into an opening. This may cause fire or electrical open the equipment. For safety reasons, the equipment should be opened only by qualified service one of the following situations arises, get the equipment checked by service personnel: The power cord or plug is damaged.

6 Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment does not work well, or you cannot get it to work according to the user 's Manual . The equipment has been dropped and damaged. The equipment has obvious signs of NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -20 C (-4 F) OR ABOVE 60 C (140 F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED : DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A).DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantechdisclaims all responsibility for the accuracy of any statements contained user Manual ContentsChapter1 Understanding Your .. 2 Figure ADAM- 6000 Module System Architecture.

7 Features .. 4 Figure ADAM- 6000 Module Dimensions .. Status .. 5 Chapter2 Hardware Selection an I/O Module .. 8 Table : I/O Selection Guidelines .. a Link Terminal and Cable .. 8 Figure Connecting ADAM- 6000 Modules to an Ethernet Ter-minal via Cable .. 9 Table : Ethernet RJ-45 Port Pin Assignment Chart .. an Operator Interface .. 9 Chapter3 Hardware Installation Introduction .. Options .. Mounting .. 13 Figure Panel Mounting Bracket 13 Figure How to Fix a Module on the Mounting Rail 14 Figure How to Fix a Module on the DIN Rail Adapter .. 14 Figure How to Secure a Module to a DIN and Connections .. Supply 15 Figure How to Connect the Module Power Wires .. Module Wiring .. 15 Chapter4 Introduction to Analog ADAM- 6000 I/O Input Modules .. 7-ch Isolated RTD Input Module .. Wiring .. 20 Figure ADAM-6015 RTD Input Wiring .. Assignment .. 8-ch Analog Input/2-ch Digital Output Module .. 20 Figure ADAM-6017 Jumper Wiring.

8 23 Figure ADAM-6017 Analog Input 23 Figure ADAM-6017 Analog Input Type 23 Figure ADAM-6017 Digital Output Wiring .. Assignment .. 24 ADAM- 6000 user Isolated Thermocouple Input/8-ch Digital Output Module .. 24 Figure ADAM-6018 8-ch Thermocouple Wiring .. 26 Figure ADAM-6018 Thermocouple Input 26 Figure ADAM-6018 Digital Output Wiring .. 12-ch Isolated Universal I/O Module .. 27 Figure ADAM-6024 Jumper Settings .. Wiring .. 29 Figure Analog I/O 29 Figure Digital Input 29 Figure Digital Output Wiring .. 30 Chapter5 Introduction to Digital ADAM- 6000 I/O I/O and Relay Modules .. 18-ch Isolated Digital I/O Module .. Wiring .. 33 Figure ADAM-6050 Digital Input 33 Figure ADAM-6050 Digital Output Wiring .. 14-ch Isolated Digital I/O Module w/2-ch Counter .. Wiring .. 35 Figure ADAM-6051 Digital Input 35 Figure ADAM-6051 Counter (Frequency) 35 Figure ADAM-6051 Digital Output Wiring .. 16-ch Source-Type Isolated Digital I/O 36 Figure ADAM-6052 Jumper Settings.

9 Wiring .. 38 Figure ADAM-6052 Digital Input 38 Figure ADAM-6052 Digital Output Wiring .. 6-ch Digital Input/6-ch Relay Module .. Wiring .. 41 Figure ADAM-6060 Digital Input 41 Figure Relay Output 6-ch Digital Input/6-ch Power Relay Module .. :.. Wiring .. 43 Figure Digital Input 43 Figure Relay Output Output Diagnostic to Obtain the Digital Output Diagnostic Status .. 45 Figure DO Diagnostic 45 Figure DO Diagnostic Status .. 46 Chapter6 System Configuration 49viiADAM- 6000 user Manual Requirements .. Adam/Apax .NET Utility ..NET Utility 50 Figure Adam/Apax .NET Utility Operation Window .. Bar .. 52 Figure Adam/Apax .NET Utility Tree Display Area .. 53 Figure Adam/Apax .NET Utility Module Display Area .. Display Area .. of ADAM- 6000 Modules .. 53 Figure Adam/Apax .NET Utility - Searching for 64 Figure All-Channel, Individual Channel, and GCL Configura-tion Controls .. Input Modules (ADAM-6015, ADAM-6017, and ADAM-6018).

10 Configuration .. 65 Figure Channels Range Configuration 65 Figure Analog Input Trend Log .. Channel Configuration .. 70 Figure Analog Input Alarm Mode I/O Modules (ADAM-6024) .. Configuration .. 71 Figure ADAM-6015 Channel Configuration .. 72 Figure Output Tab .. Digital I/O Modules (ADAM-6050, ADAM-6051- ADAM-6052, ADAM-6060, ADAM-6066) .. Configuration .. Channel Configuration .. 74 Figure Input 75 Figure Output Modes .. 78 Figure Explaining Low to High Delay Output Mode .. 80 Figure Explaining Low to High Delay Output Mode .. to P2P Functions .. Communication Modes .. 82 Figure Mode for 82 Figure mode for Communication Methods .. Event to Configure P2P Functions .. 84 Figure to Peer/Event Tab .. Mode 85 Figure Basic Mode Mode 86 Figure Advanced Mode Configuration .. 86 Figure One Setting to Other Channels .. Web 5 .. Applet Customization .. 90 Figure of the file .. 93 Figure 93 Chapter7 Planning Your Application.