User Manual and Installation Guide Pro Wireless …

1 ISSUED: 07-24-12 SHEET #: 180-9023-1 User Manual and Installation GuidePro Wireless Multimedia KitModels:HDS200 HDS200-2 HDS200-3 HDS200-4 READY 3 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 ContentsSafety Precautions ..4 Proper Care and Safety ..4 Unit Care Recommendations ..4 Introduction ..5 Features ..5 Package Contents ..5 Product Specifi Format Supported ..7 Audio Format Supported ..7 Wireless Connection ..7 WiFi Channel Frequencies ..7 Transmitter ..8 Receiver ..12 Remote Control ..16 Installation and Operation ..19 Selecting Input and Output Port ..23 Peer-to-Peer and Multicast LAN (wired) Mode Installation ..23 Peer-to-Peer Direct LAN Connection ..23 LAN Connection Through Router (LAN One-to-One) ..24 Confi guring for LAN Through Router (LAN One-to-One) ..24 Indicator Lights Decoded ..25IR Flasher ..26IR Extender ..26 Product Modes ..26 Peer-To-Peer Modes ..26 Multicast Modes ..27 LAN - Wired Connection Mode.

2 27 FAQs ..28 Appendix ..30 Warranty ..34 Contact Information ..354 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Please read this Manual before using the product. Unit can be placed vertically (preferred) or horizontally. To clean, use a soft, dry cloth only. Do not use water or other cleaning products as they may cause electrical failure or damage the surface of the the product out of reach of the product away from external heat sources such as heaters or there is any unusual sound, smoke or odor coming from the product, immediately unplug the product and call Peerless-AV Customer Care at the battery of remote control out of reach of not attempt to open the outer case of the Transmitter or Receiver. Doing so will void the product the remote control away from humidity and/or not insert foreign objects into the not place the unit on an unstable surface or in a poorly ventilated sure to plug the AC power adapters fi rmly into wall not use the unit near any fl ammable substances or combustible Care and SafetyUnit Care RecommendationsSafety PrecautionsIf any part of the AC power adapter looks damaged, do not use the product and immediately call Peerless-AV Customer Care at the product unplugged if unused for an extended period of of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1HD Flow Pro Wireless Multimedia Kit provides Full HD 1080p signal transfer, including 3D signal*, without the hassle of running cables.

3 Create brilliant HD quality multimedia for signage, presentations, or entertainment in any location,completely un-tethered to your source device!By simply connecting the Transmitter to a multimedia device such as a computer, set-top box, or Blu-ray player and connecting the Receiver to a display device, instant real-time high defi nition digital audio and video can be placed into in any commercial or residential setting. HD Flow Pro Wireless Multimedia Kit transmits through walls and fl oors to allow the components to be neatly tucked away in an AV rack or media cabinet, and is the ideal solution for quick and easy Installation where running cable is cost prohibitive or simply not an option. * Works with passive 3D signalsFeatures Low latency: 30ms. Supports both digital (HDMI) and analog (Component, Composite) video/audio. Supports Wireless or Wired connection - IEEE 5 GHz WiFi, LAN connection.

4 Two internal antennas (supporting MIMO). HDCP compliant. Supports both DTV & VESA standards: DTV: 1920x1080i60/p60, 1280x720p60, 720x480i60/p60,VESA : WSXGA+(1680x1050), SXGA(1280x1024), WXGA(1280x800), XGA(1024x768), SVGA(800x600), VGA(640x480). Supports passive 3D content. Plug and play setup requires no software ContentsEnsure that the following items are present in the package. If any items are missing or damaged, please call Peerless-AV Customer Care at 1-800-865-2112 (available 7:00am - 7:00pm CST Monday - Friday).TransmitterRemote ControlReceiverIR-FlasherComponentAdapte rBatteryManualStand (2)Quick Start GuideAC Adapter (2)IR-ExtenderIntroductionStep 7 While turning on the display device the HD Flow Pro Wireless Multimedia units will be going through the startup process. This process may take up to two minutes to complete. The Power/Link indicator lights on the Transmitter and the Receiver will be flashing at first.

5 Flashing indicates that the units are establishing a secure connection. Wait until the connection is successfully established, indicated by the Power/Link indicator light becoming x Transmitter1 x Receiver2 x Stand1 x Remote Control1 x IR Flasher1 x IR Extender1 x Component Adaptor 2 x Power Adapter1 x Quick Start Guide1 x Users ManualStep 2 Connect the provided IR Flasher to the IR-OUT port on the Transmitter. Find the location of the IR window on your component device and adhere the IR Flasher eye directly over the IR window on your component device. NOTE: One IR Flasher eye is to be used for one component 4 Irovided IR Extender in to the IR-IN port on the Receiver and adhering the other end of the IR Extender to a vertical surface near the output device. Ensure that the IR Extender is in a line of sight to the remote control that controls your source devices. NOTE: For Multicast models, receivers two, three and four do not come with an IR Extender.

6 Additional IR Extenders (HDS-IRE) can be purchased separately; visit for more 6 Turn on your display device (TV, monitor, projector, etc.).Step 3 to the Receiver. S1. Plug in the power adapter for the Transmitter and the Receiver to nearby available power Plug in the power adapter end to the Transmitter and then to the The units will automatically turn-on. The average power-on/sync time is approximately two s in the BoxInstallation and SetupTroubleshooting TipsTip The IR window may be easier to locate with a direct light shining on sections of the front panel of the component device. A small flashlight works Selection ButtonTip Repeat Steps 3-11 to more tReceiv(HDS20 HDS20 HDS20 Step 1 Connect the Transmitter to the source devices (Blu-ray Disc player, set top box, gaming console, etc.).Step 9 Turn on the desired source device that is connected to the 11 Play the source device content and enjoy up to Full HD 1080p Wireless entertainment Check the media source resolution.)

7 The display device must be able to support the resolution of the media source that is being streamed. Utilizing the INFO button will allow you to see the resolution data that the display device supports. If the display device supports the highest resolution of 720p but the source device is outputting 1080p content, the content needs to be down-scaled to the maximum resolution of the display device, in this case 720p. Receiver Output Indicator Light Blinks:t Make sure that your display device, source device and the HD Flow Pro units are all turned ON and the Receiver is properly connected to the output device. t Verify that the Receiver is set to the appropriate output Check the resolution setting of your source device. This may need to be changed to a resolution supported by the HD Flow Pro unit. Reference the Resolution Chart in the HD Flow Pro Manual for compatibility. Reference your source devices Manual for instruction on changing the output the above troubleshooting tips do not resolve the issues for a unicast setup, please reference the Factory Reset Section of the HD Flow Pro Manual .

8 For a multicast system configuration, please contact Peerless-AV Customer Care at 800-856-2112 for further 8 Select the output that connects the Receiver to the display using the Power/Source Selection Button or the provided remote control. The output indicator light will become solid and the HD Flow logo will appear on the display 10 Select the desired source or device input on the Transmitter using the Power/Source Selection Button on the remote and/or Receiver Indicator Lights are all Blinking:t The HD Flow Pro units are establishing a connection. It can take up to two minutes for the HD Flow Pro units to establish a complete connection. If after two minutes have passed and the units have not established a connection, unplug the power cable, wait 30 seconds and reconnect the power supply to the or Receiver Power Indicator Light is OFF:t Check and verify the power supply Input Indicator Light Blinks:t Make sure that your source device is turned ON and the cable is properly Verify that the Transmitter is set to the appropriate input Check the resolution from your source device.

9 This may need to be changed to a resolution supported by the HD Flow Pro Wireless Multimedia Kit. Reference the Resolution Chart in the HD Flow Manual for compatibility. Reference your source devices Manual for instruction on changing the output resolution. Receiver Power Indicator Light Blinks:t Verify that the HD Flow Pro Transmitter and Receiver are within the recommended range of 131 feet. Physical obstructions such as walls, floors and ceilings between the Transmitter and Receiver may decrease the strength of the connection signal and reduce the overall transmission a connection has been established and the HD Flow logo can be seen on the display device, but content is not playing:t Make sure that the input/output cables are properly Verify that the Transmitter is set to the appropriate input Do not place the HD Flow Pro units near other devices that emit excessive amounts of heat. Increased temperatures may cause the HD Flow Pro Transmitter or Receiver unit to malfunction or stop Start Guide for HD Flow Pro Wireless Multimedia Kit - LIT-0906 Power/Source Selection Button 2012 Peerless Industries, Inc.

10 Peerless-AV is a trademark of Peerless Industries, Inc. All rights Flow is a trademark of I Do It, LTD. Other parties marks are the property of their respective owners. Start GuidePRO Wireless MULTIMEDIA KITM odel No. HDS200 (-2, -3, -4)READY ISSUED: 06-12-12 SHEET #: 180-9023-1 User Manual and Installation GuidePro Wireless Multimedia KitModels:HDS200 HDS200-2 HDS200-3 HDS200-4 READY 6 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-12 x HDMI up to 1080p (60Hz)1 x Composite1 x YPbPr Component1 x HDMI up to 1080p (60Hz)1 x Composite1 x YPbPr Baseline Profile with Level compliantWireless ConnectionSupporting IEEE : OFDMRJ-45 LAN PortDirect Connection (LAN Cable)1 x LAN Port (Transmitter and Receiver)10/100 BaseUSB1 x USB Type A Female (Receiver)Audio Input1 x Audio Jack, 1 Stereo RCA Audio Jack (Transmitter)Audio Output1 x Audio Jack, 1 Stereo RCA Audio Jack (Receiver)Video Resolution480i/p, 720p, 1080i/p (24/30/60fps)Streaming Latency< 30ms - Connection10/100 BaseRange131ft (40m) maxiumBroadcast1 Transmitter up to 4 Receivers* , , WPA2, WPA and WEP 64/128 TKIP AES2 x Internal Antenna (Transmitter and Receiver)MIMO InterfaceIR Flasher3 IR FlashersIR Extender IR-ExtenderColorBlackVoltage: 12 VDCAmps: 2 AConsumption: 12V 2 AAntenna TypePowerHDS200 Models*Requires additional Receiver unitsVideo Input (Transmitter)Video Output (Receiver)EncodingWired ConnectionLANP roduct Specifi cations7 of 36 ISSUED: 07-24-12 SHEET #.