User Manual: Model 1700 Transmitters with Analog Outputs

1 Configuration and Use ManualMMI-20019028, Rev ABMarch 2018 Micro Motion Model 1700 Transmitters withAnalog OutputsConfiguration and Use ManualSafety messagesSafety messages are provided throughout this manual to protect personnel and equipment. Read each safety message carefullybefore proceeding to the next informationFull product specifications can be found in the product data sheet. Troubleshooting information can be found in the configurationmanual. Product data sheets and manuals are available from the Micro Motion web site at policyFollow Micro Motion procedures when returning equipment. These procedures ensure legal compliance with governmenttransportation agencies and help provide a safe working environment for Micro Motion employees.

2 Micro Motion will not acceptyour returned equipment if you fail to follow Micro Motion procedures and forms are available on our web support site at , or by phoning the Micro Motion CustomerService Flow customer serviceEmail: Worldwide: Asia-Pacific: and South AmericaEurope and Middle EastAsia PacificUnited 240 1978 Australia800 158 727 Canada+1 303-527-5200 The Netherlands+31 (0) 704 136 666 New Zealand099 128 804 Mexico+41 (0) 41 7686 111 France0800 917 901 India800 440 1468 Argentina+54 11 4837 7000 Germany0800 182 5347 Pakistan888 550 2682 Brazil+55 15 3413 8000 Italy8008 77334 China+86 21 2892 9000 Central & Eastern+41 (0)

3 41 7686 111 Japan+81 3 5769 6803 Russia/CIS+7 495 981 9811 South Korea+82 2 3438 4600 Egypt0800 000 0015 Singapore+65 6 777 8211 Oman800 70101 Thailand001 800 441 6426 Qatar431 0044 Malaysia800 814 008 Kuwait663 299 01 South Africa800 991 390 Saudi Arabia800 844 9564 UAE800 0444 0684 ContentsPart IGetting startedChapter 1 Before you begin .. this manual .. Model code .. tools and protocols .. documentation and resources ..4 Chapter 2 Quick start .. up the transmitter .. meter status .. status reported by LED .. a startup connection to the transmitter .. (Optional) Adjust digital communications settings .. mass flow measurement.

4 The zero .. used with zero verification and zero calibration ..9 Part IIConfiguration and commissioningChapter 3 Introduction to configuration and commissioning .. flowchart .. values and ranges .. access to the off-line menu of the display .. write-protection on the transmitter configuration .. the factory configuration ..16 Chapter 4 Configure process measurement .. mass flow measurement .. Mass Flow Measurement Unit .. Flow Damping .. Mass Flow Cutoff .. volume flow measurement for liquid applications .. Volume Flow Type for liquid applications .. Volume Flow Measurement Unit for liquid applications.

5 Volume Flow Cutoff .. GSV flow measurement .. Volume Flow Type for gas applications .. Standard Density of Gas .. Gas Standard Volume Flow Unit .. Gas Standard Volume Flow Cutoff .. Flow Direction .. for Flow Direction .. density measurement .. Density Measurement Unit .. 39 ContentsConfiguration and Use two-phase flow parameters .. Density Damping .. Density Cutoff .. temperature measurement .. Temperature Measurement Unit .. Temperature Damping .. of Temperature Damping on process measurement .. Temperature Input .. pressure compensation .. pressure compensation using ProLink III.

6 Pressure compensation using the Field Communicator .. for Pressure Measurement Unit ..49 Chapter 5 Configure device options and preferences .. the transmitter display .. the language used for the display .. the process variables and diagnostic variables shown on the display .. the number of decimal places (precision) shown on the display .. the refresh rate of data shown on the display .. or disable automatic scrolling through the display variables .. or disable the display backlight .. or disable Status LED Blinking .. or disable operator actions from the display .. or disable Totalizer Start/Stop from the display.

7 Or disable Totalizer Reset from the display .. or disable the Acknowledge All Alerts display command .. security for the display menus .. response time parameters .. Update Rate .. Response Time .. alert handling .. Fault Timeout .. Status Alert Severity .. informational parameters .. Sensor Serial Number .. Sensor Material .. Sensor Liner Material .. Sensor Flange Type .. Descriptor .. Message .. Date ..69 Chapter 6 Integrate the meter with the control system .. the transmitter channels .. the mA output .. mA output Process Variable .. Lower Range Value (LRV) and Upper Range Value (URV).

8 AO Cutoff .. Added Damping .. mA output Fault Action and mA output Fault Level .. the Frequency output .. Frequency output Polarity ..80 ContentsiiMicro Motion Model 1700 Transmitters with Analog Frequency output Scaling Method .. Frequency output Fault Action and Frequency output Fault Level .. the Discrete output .. Discrete output Source .. Discrete output Polarity .. Discrete output Fault Action .. events .. a basic event .. an enhanced event .. digital communications .. HART/Bell 202 communications .. HART/RS-485 communications .. Modbus/RS-485 communications .. Digital Communications Fault Action.

9 98 Chapter 7 Complete the configuration .. or tune the system using sensor simulation .. simulation .. up transmitter configuration .. write-protection on the transmitter configuration .. 103 Part IIIO perations, maintenance, and troubleshootingChapter 8 transmitter operation .. the process variables .. process variables .. process variables using the display .. process variables and other data using ProLink III .. process variables using the Field Communicator .. transmitter status using the status LED .. and acknowledge status alerts .. and acknowledge alerts using the display .. and acknowledge alerts using ProLink III.

10 Alerts using the Field Communicator .. totalizer and inventory values .. and stop totalizers and inventories .. and stop totalizers and inventories using the display .. totalizers .. totalizers using the display .. inventories ..118 Chapter 9 Measurement support .. for measurement support .. Smart Meter Verification (SMV) .. requirements .. test preparation .. SMV .. test data .. automatic execution of the SMV test .. PVR, TBR, and TMR .. , TBR, and TMR applications .. linearization (PWL) for calibrating gas meters ..134 ContentsConfiguration and Use the meter .. the meter .. method for calculating the meter factor for volume flow.