User Manual - outspot.be

1 EN 01 User ManualModel: DO-SV-BTSB2-BEnglish1) PACKAGE CONTENTS Wireless BT soundbar with integrated subwoofer Remote control Power cord Wall mount brackets Screws mm mm audio cable mm RCA audio cable User Manual 2) SAFETY INSTRUCTIONSThe following basic precautions must always be taken before using the Dutch Original - Wireless BT soundbar with integrated subwoofer , hereinafter referred to as the device .General information Read the instructions for use carefully and keep them safe. If you give this device to other people, please also pass on this Manual .

2 Only use this device in accordance with the instructions in this user Manual . The device is not a toy. Keep it out of the reach of children and pets. All warnings on the appliance and in the operating instructions should be adhered to. WARNING! Do not leave packaging material lying around carelessly. This may become dangerous playing material for children. Risk of suffocation!TABLE OF CONTENT: 1) Package contents2) Safety instructions3) Installing and using the product4) Specification5) Storage & transportationEN 02 Electricity and heat Prior to use, check that the mains voltage is the same as the mains voltage stated on the device.

3 Make sure your hands are dry before touching the device, power cord / plug. Insert the power plug into an electrical outlet that is easily accessible at all times and a socket designed for 2 round pins (Types C, E, F, J, K and L). Do not operate the device using an external time switch or a separate remote control system. WARNING! Never cover the device & power cord with cloths, curtains or any other material to prevent overheating and possible fire hazards. To reduce or prevent the risk of personal injury, electrical shock, fire or damage; never insert metal objects into any openings of the device, power cord or power socket.

4 When removing the power plug from the electrical outlet, always pull the power plug, never yank on the cord. Check the power cord regularly for damage. Never use the device if the power cord shows signs of damage, if the device has fallen on the ground or shows any other signs of damage. Remove the power plug from the socket when the device is not in use or is being cleaned. Make sure the power cord cannot be trodden on or pinched. Do not allow the power cord to hang over sharp edges and keep it away from hot objects and naked flames. When plugging in the power cord, make sure people cannot accidentally pull it out or trip over it.

5 Remove the power cord from the power socket during lighting storms or if unused for long periods of time. This device is a Class ll or double insulated electrical device. As a result, it does not need to be electrically earthed. Batteries and heat Make sure the remote control battery compartment is secured. Only use batteries specified in the battery compartment (CR2025 / 3V). Make sure you respect the polarity when placing batteries. Do not short-circuit contacts inside the battery compartment or any batteries. To avoid leakage, remove the battery if the remote control is not used for a long period of time.

6 Empty batteries should be removed from the remote control to avoid leakage. If the battery leaks, do not allow battery fluid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice. Keep batteries out of the reach of children. Do not expose the remote control to excessive heat sources like fire or direct sunlight (including amplifiers).EN 03 Do not crush, puncture or dismantle the remote control; this might damage the battery. Damaging the casing of the remote control and/or piercing it can lead to explosion or fire!

7 Do not throw the remote control or battery into a fire because it may explode! Do not dispose of batteries in your household waste. Batteries can be disposed of by taking them to your local recycling centre. Contact your local government offices for This device is intended for domestic or similar use. Only use the device indoors, in dry areas and not in the vicinity of water, other liquids or humidity. Avoid locations subject to vibrations, excessive dust, cold or humidity. Do not install near heat sources like radiators, heaters, stoves, or other equipment (including amplifiers) that produces heat.

8 Do not expose the device to direct sunlight, excessive humidity or corrosive environments. Do not block ventilation openings. Minimum distance around the apparatus for sufficient ventilation is 5 cm. Ventilation should not be impeded by covering ventilation openings with items like newspapers, tablecloths, curtains, etc. Do not place the device under mechanical stress. Do not use or store the device in an environment subject to strong static electricity or magnetic fields. Improper use of the device could damage the product. Please handle the device carefully.

9 Impacts or falls, even from a low height, can damage the device. Do not use the device if it has fallen into water or any kind of fluid. Do not open the cabinet as this may result in electric shock. Do not attempt to disassemble or repair the device, or modify it in any manner. The device must be serviced if it has been damaged in any way, the power supply cord is damaged; liquid has been spilled; objects have fallen into it; it has been exposed to rain or moisture; has been dropped or does not operate normally. WARNING! To reduce the risk of fire or electric shock, protect the device from dripping or splashing water, and keep away from objects filled with liquids, such as vases.

10 These objects should not be placed on or near the device. Do not use abrasive cleaning solvents to clean the device. Do not use foreign objects to clean the device. WARNING! To prevent possible hearing damage, do not listen at high volume for long 043) INSTALLING AND USING THE DEVICEOpen the packaging carefully before taking out the device. Make sure the device is complete and undamaged. If any components are missing or damaged, contact the vendor and do not use the product. Retain the packaging or recycle it in accordance with local & features device Power ON/OFF button (Standby mode) SRC button, select the input source.