User's manual CAUTION Battery Charger/PC Linkage Device ...

1 UM-7FJ0A-003-00 User's manual CAUTION . Features Example of connection for charging The *1PC Linkage Device can be used to connect a PC to the bicycle (system or unit), Battery Charger/PC Linkage Disconnect the USB cable or the charging cable when performing maintenance. and an *2E-tube Project can be used to carry out tasks such as updating *3firmware of single units and system, and customizing. Device (SM-BCR2) Note: * 1 PC Linkage Device : SM-PCE1/SM-BCR2. * 2 E-tube Project: the PC application Do not use outdoors or in environments with high humidity. * 3 Firmware: the software inside each unit Do not place the PC Linkage Device on dusty floors when using it.

2 User's manuals in other languages are available at : Place the PC Linkage Device on a stable surface such as a table when using it. Do not place any objects on top of the PC Linkage Device or its cables. Names of parts Do not wrap the cables into bundles. Do not connect the charger to PC when it is on standby. This may cause a failure USB cable IMPORTANT NOTICE of PC depending on its specifications. Do not hold the PC Linkage Device by the cables when carrying it. Contact the place of purchase or a bicycle dealer for information on installation Do not apply excessive tension to the cables. Charging port and adjustment of the products which are not found in the User's manual .

3 A dealer's manual for professional and experienced bicycle mechanics is available Connect the PC Linkage Device directly to a computer, without using an intermediate Device such as a USB hub. Micro USB plug USB plug on our website ( ). Connect to the Connect to a PC USB port or an Do not disassemble or alter this product. Do not ride the bicycle while the PC Linkage Device and cable are still connected Battery charger . AC adapter with a USB port. to it. For safety, be sure to read this User's manual thoroughly Do not connect two or more of the same units to the same connection point. If Charging port this is not done, the units may not operate correctly.

4 Before use, and follow them for correct use. Battery charger To an AC adapter with a USB port Do not connect or disconnect units again while unit recognition is in progress or or PC. after recognition is complete. If this is not done, the units may not operate correctly. * The position of the charging port differs depending on the product. Check the procedures which are given in the User's manual for the E-tube Important Safety Information Project when connecting and disconnecting units. Do not wash the PC Linkage Device or wipe it using detergents. Guidelines that require replacement, contact the place of purchase or a bicycle dealer.

5 Do not connect two or more PC Linkage devices at the same time. If two or more Troubleshooting for charging error CHARGE indicator ERROR indicator Be sure to observe the following in order to avoid burns or other injury from fluid PC Linkage Device units are connected, they will not operate correctly. In leakages, overheating, fire or explosions. addition, operating errors may occur at the PC and it may require the PC to be 1. Reconnect the charging cable or USB cable, try charging again. Micro USB Plug for product connection restarted. connector (Connect to the junction (A) or the charging 2. If the ERROR indicator blinks, the ambient temperature during charging may PC Linkage Device cannot be used while the charger is connected.)

6 Connector of the information display.) fall outside the operating temperature limits. Check that the temperature is DANGER Use this instrument under the direction of a safety supervisor or the direction for * If water collects in the connector of the product appropriate. use. Do not allow physically, sensory, or mentally impaired persons, side, wipe the water and then connect the plug 3. If the CHARGE indicator blinks, refer to the following. Do not get the charger wet or use it while it is wet, and do not touch or hold it inexperienced persons, or persons with no required knowledge including to the connector. The current capacity of your AC adapter with a USB port is lower than Adc.

7 With wet hands. If this is not observed, problems with operation or electric children to use this instrument. Use an AC adapter with a USB port with a current capacity equal to or shocks may occur. Special Battery higher than Adc. Do not allow children to play near this instrument. Do not cover the charger with a cloth or similar while it is in use. If this is not A USB hub is used to connect to PC. Charge the Battery in indoor places to avoid exposure to rain or wind. This charger is a special charger for use in charging Shimano lithium ion batteries observed, heat may build up and the case may become deformed, or fire or (SM-BTR2).

8 Remove the USB hub. overheating may occur. Products are not guaranteed against natural wear and deterioration from For other batteries, refer to their manual . If none of the above 1 to 3 is the case, the Battery or junction may be faulty. normal use and aging. Never connect any incompatible batteries. A burst or fire may be caused. Contact a dealer. Do not disassemble or modify the charger . If this is not observed, electric shocks or injury may occur. For maximum performance we highly recommend Shimano lubricants and * Fully understand and follow the precautions for use. If the Battery is charged by using PC, check the following points as well.

9 Maintenance products. 4. Make sure that only one unit of SM-BCR2 is connected to PC. Use an AC adapter with a USB port with a voltage of Vdc and with a current equal to or higher than Adc. If the one with a current lower than A is This equipment has been tested and found to comply with the limits for a Class used, the AC adapter may heat up, potentially causing a fire, smoke, B digital Device , pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential Charging method * If the CHARGE indicator does not light up or goes out soon, the Battery may be overheating, destruction, electric shock, or burns.

10 Fully charged. Check the remaining power of the Battery using the junction (A). installation. This equipment generates, uses and can radiate radio frequency or information display. energy and, if not installed and used in accordance with the instructions, may You can charge the Battery by using the AC adapter with a USB port or connecting If the Battery is found low or dead, contact the place of purchase or a bicycle cause harmful interference to radio communications. However, there is no the Battery charger to a PC USB port. WARNING guarantee that interference will not occur in a particular installation. If this 1.