VALUE-LINE® 3-PIECE THREADED AND SOCKET …

1 B105-4 1/2009 Factory-engineered linkage kits are available tofacilitate the mounting of electric and DataThe table below provides flow coefficients ofStandard-bore Series 3 valves. The Cvvalues representthe flow of water at +60 F through the valve in per minute at a pressure drop of 1 psi. Themetric equivalent, Kv, is the flow of water at 16 Cthrough the valve in m3/hr at a pressure drop of 1 convert Cvto Kv, multiply by 3-PIECETHREADED AND SOCKET -WELD BALLVALVES, SERIES 3A & 3 CThe JAMESBURY VALUE-LINE Series 3 three-piece ballvalve offers exceptional economy and proven per-formance.

2 These valves are available in either threadedor SOCKET -weld configuration. The large port sizeprovides high flow while minimizing pressure body materials for the Series 3 valves are:Carbon steel with 316 stainless-steel trim and all 316stainless steel. The stainless body caps of the 3-seriessocket weld valves are furnished with 316L (A351-CF3M)as standard. Seat materials are PTFE and filled PTFE which allow these valves to handle the vast majorityof commonly encountered chemicals up to the fullbody rating, and steam to 250 psi (17 bar) (saturated).Stainless-steel fasteners are pressure rating of these Series VALUE-LINE valvesis 1000 psi (68 bar) CWP.

3 The seat and seal CWP ratingare the same as the valve body. Seat temperatureratings are -60 to +500 F (-50 to +260 C).The Series 3 is available with a wide variety of factoryengineered actuation Three-piece design facilitates easy in-line serviceand allows welded installation without damagingsoft parts. A slide-lock handle is standard, meeting the require-ment of OSHA Flexible-lip seats are self-compensating for wear andthe effects of temperature and pressure fluctuations. Positive stem retention is provided by an internalentry stem. A full complement of standard accessories such asstem extensions and round handles is are interchangeable with those ofSeries 3000 SizeStandard BoreEquivalent lengthinchesDNCvof pipe feetmeters1 BULLETIN 1/092 METSOB105-410080605040302010865432 Maximum Differential Pressure, psi10 20 30 40 50 60100 200 300 400 500 600 700 800 900 1000 Maximum Differential Pressure.

4 Bar1005020105 Valve Seat RatingsThese ratings are based on differential pressure with valveball in the fully closed position and refer to seats to valve body ratings below to be sure that all com-ponents are satisfactory for the in carbon steel are suitable for service to -20 F (-29 C),valves in 316 stainless steel to -60 F (-51 C).Valve Body RatingsThese are the maximum working pressure ratings of thevalve body only. The seat ratings determine the practicalpressure limitation in actual service. Working pressurerating is at -20 F to +100 F (-29 C to +38 C).Working Pressure forValveBody Material.

5 Carbon Steel andSize316 Stainless Steel with 300 SeriesStainless Steel BoltingInchesDNpsibar1/2 215 50100069 Recommended Actuator Torque, FT LBSR ecommended Actuator Torque, N m2"(DN 50)1-1/4"(DN 30)1-1/2"(DN 40)1" (DN 25)3/4"(DN 20)1/2" (DN 15) 10080605040302010865432 Maximum Differential Pressure, psi10 20 30 40 50 60100 200 300 400 500 600 700 800 900 1000 Maximum Differential Pressure, bar1005020105 Recommended Actuator Torque, FT LBSR ecommended Actuator Torque, N mPTFE (T)-Seated Reduced Bore ValvesFilled-PTFE (M)-Seated Reduced Bore ValvesT = PTFEM = Filled PTFEM aximum Differential Pressure, psiTe m p e r a t u r e FTe m p e r a t u r e CMaximum Differential Pressure, barSaturatedSteamLowTemperatureLimit of Carbon SteelTM120011001000900800700600500400300 200100070503010-50 0 50 100 150 200 250 300-60 0 100 200 300 400 500 600-201/2" - 2" (DN 15 - 50) Standard PortValve Torque DataThese torque charts for Series 3 valves are to be used as aguide for actuator selection.

6 An actuator should beselected that provides the same or greater torque outputthan that shown in the appropriate chart. Refer to thebulletins on JAMESBURY pneumatic and electric actuatorsfor torque output values and actuator selection requirements may be imposed by mediacharacteristics, trim, and frequency of valve operation. Forclean lubricating fluid service, required torque for PTFE ( T )and filled PTFE(M) seated valves onlymay be reduced 20%when the valve is equipped with 316 stainless steel difficult service (slurries, semi-solids), increase valuesby 50%.If in doubt, select a larger shown in the charts are based on standard factoryprocedures for valve-actuator "(DN 50)1-1/4"(DN 30)1-1/2"(DN 40)1" (DN 25)3/4"(DN 20)1/2" (DN 15)

7 TECHNICAL BULLETIN 1/093 VALUE-LINE 3-PIECE THREADED AND SOCKET -WELD BALL VALVES, SERIES 3A & 3CB105-4 Dimensions inchesValve mmValve NameBody MaterialNumberCarbon Steel316 Stainless Steel11 BodyASTM A216-WCB -Carbon steelASTM A351-CF8M -Stainless steel22 Body CapASTM A216-WCB -Carbon steelASTM A351-CF3M -Stainless steel31 Ball316 Stainless steel41 Stem316 Stainless steel52 SeatPTFE/Filled PTFE62 Body SealPTFE72 Stem SealPTFE81 Stem BearingPTFE91 Shakeproof WasherCarbon steel304 Stainless steel151 HandleCarbon steel304 Stainless steel162 Stem Nut304 Stainless steel181 Compression Ring304 Stainless steel194 Hex Nut300 Stainless steel204 Body Bolt300 Stainless steel214 Lockwasher300

8 Stainless steelBILL OF MATERIALS AND PARTS LIST S1/4 RW15H2119EJ2026135188AB91647 GSubject to change without prior Automation ,Levytie 6, Box 310, 00811 Helsinki, +358 20 483 150. Fax +358 20 483 151 North America,44 Bowditch Drive, Box 8044, Shrewsbury, MA 01545, +1 508 852 0200. Fax +1 508 852 8172 Europe,6-8 rue du Maine, 68271 Wittenheim Cedex, +33 (0)3 89 50 64 00. Fax +33 (0)3 89 50 64 40 South America,Av. Independ ncia, 2500- Iporanga, 18087-101, Sorocaba-S o PauloBrazil. Tel. +55 15 2102 9700. Fax +55 15 2102 9748/49 Asia Pacific,238A Thomson Road, #25-09 Novena Square Tower A, 307684 +65 6511 1011.

9 Fax +65 6250 0830 China,19/F, the Exchange Beijing, No. 118, Jianguo Lu Yi, Chaoyang Dist, 100022 Beijing, +86-10-6566-6600. Fax +86-10-6566-2575 Middle East,Roundabout 8, Unit AB-07, Box 17175, Jebel Ali Freezone, Dubai,United Arab Emirates. Tel. +971 4 883 6974. Fax +971 4 883 HandleOnlyCenterline of ValveValve Oval and Round SizeHandle DimensionsInchDNAH inchmminchmm1 TO ORDER JAMESBURY BRAND 3-PIECE VALVESS pecify the valve you require by constructing a 12-character type code from the following :The valve specified is a 2" size with a standard-bore NPT body style with carbonsteel body, 316 stainless-steel ball and stem, PTFE/PTFE seats and seals, and standard 300stainless steel 2236 TT-31 Sizeinches1/23/411-1/41-1/22DN1520253040 50 ACCESSORIESH andlesThe Series 3 ball valves described in this bulletin have twotypes of optional handles available, a round handle (notlockable) and a lockable oval handle.

10 Both are available ina choice of carbon steel or stainless steel material. To orderhandles separately, specify the following part SizeHandleMaterial1/2" -3/4"1" -1-1/4"1-1/2" -2"Type(DN 15 20)(DN 25 30)(DN 40 50)RoundCarbon Steel012-0785-22012-0786-22012-0787-22 HandlesStainless Steel012-0785-30012-0786-30012-0787-30 LockableCarbon Steel012-0794-22012-0795-22012-0796-22 Oval HandlesStainless Steel012-0794-30012-0795-30012-0796-302 Series and Body Style3A3-piece standard-bore screwed NPT ball valve3C3-piece standard-bore SOCKET -weld ball valveStem ExtensionsValve SizePartinchesDNNumber1/2 3/415 20SE-0721 1-1/425 30SE-0731-1/2 240 50SE-0743 Body/Trim Material2236 Carbon steel body/316 stainless steel ball & stem3600316 Stainless steel body.