Transcription of VIBRATORS FOR PLATING TANKS - Made in the …
1 VVIIBBRRAATTOORRSS FFOORRPPLLAATTIINNGG TTAANNKKSSIINN PPRRIINNTTEEDD CCIIRRCCUUIITT IINNDDUUSSTTRRYYWe re The Vibrator Guys. DATAIDEAS FOR BETTER PLATINGWITH VIBRATION Achieve Better PLATING with Proper Vibration Reduce RejectsVIBCO has designed a special line of electric &pneumatic VIBRATORS for the PC-board industry. Astate-of-the-art painting system allows special epoxypaint to withstand acid fumes, paint chipping andrust. Vibco s continuing research is now investigat-ing plastic and stainless steel the years many VIBRATORS have been used inthe PC-board industry with a high failure rate, dueto the fumes from the bath attacking the vibrator,improperly mounting of the vibrator on TANKS andracks causing fatigue cracks, overloading thevibrators and burning them out or damaging use of rubber isolators inducing air intothe bath instead of removing it.
2 All this has addedunnecessary cost to the PC-boards as well asmachinery and labor. Vibco has designed specialvibrators and isolation systems to give the cus-tomer a product that takes into account the spe-cialty of the application and provides long equip-ment also has specialized application engineerswell acquainted with the PC-boards industry who can help you with your installation and answerany questions you may have such as choice ofvibrator, cost, engineering support, best placementof vibrator, : Special epoxy paint to withstand the fumesfrom the bath. Special seals to prevent fumes from entering the vibrator. High temperature lubricant in the bearings. High temperature insulation on thewindings to give extra safety factor &extra long life. No lubrication necessary on the pneumaticunits eliminating exhausting oilthat contaminates bath or * DutyInt.
3 DutyVibrations per ** (Impact) *Amps shown 115V. **Decibel at 3' (1 meter on A-Scale) **Adjustable eccentrics **12 & 24 Volt DC See catalog 9112 SCR-60 CESCR-100 CESCR-300 CESCRW-400 CECE-60DC-60 SPWT-80 CEModel1 phase3 phaseForce (Impact) at **115/230230 .121226 **115/230115/230115/23012/24115 VPMS peed PSI60 **23 Most Commonly Used VibratorsDIMENSIONSM odelE**inch / mm63/863/481/2963/853/877/8103/451/463/4 63/416218721622914013720027313317117141/ 2641/861/441/251/241/847/833/1639/164114 1521051591141140105124819010231/441/4553 /831/461/2561/437/16315/1647/88310812712 7831651271598710012435/85351/435/843/433 1/2455641277613364121768910212712715/16 53/441/415/1623/4411/1663/8 3314511433701191625/163/85/167/165/163/8 5/161/23/81/21/2810814810813101313 1/41/43/87710 3/83/81/2101013 SCR-60 CESCR-100 CESCR-300 CESCRW-400 CECE-60, DC-60 SPWT-80CE2P-75CE2P-150 CEBVS-190 CEBVS-250 CEBVS-320 CESCR-60 CESPWT-80 CESCR-100 CESCRW-400CE2P-75CE2P150-CECE-60 CESCR-300 CEDC-60 The SCR-line is speed and force adjustable while in operation.
4 Each unit supplied with a speeddial control. Specify if for 115 volt or 230 volt single phase, standard 50 or 60 cycles, SCR-60 CEand SCRW-400CE have O-ring sealed housings for pressure wash CE-60CE and SPWT-80CE 115 or 230 volt, single phase, 50 or 60 cycles and 3200 vibra-tions per minute. Units are speed adjustable with standard speed controls, both high pressurewash down 2P - Single or 3-phase operation can be made in any voltage and 50 or 60 cycles con-stant speed units with adjustable eccentrics for adjustable force BVS - Silent Pneumatic Turbine VIBRATORS - Silent operation, need no airline lubrication,bearings prelubricated for life. Totally enclosed for high pressure wash down. Tapped exhaust portfor leading off exhausting more technical data and other available units ask for General Catalog # MODELSPNEUMATIC MODELS*Bolt Size **Air Inlet NPT Pipe Thread Air Exhaust NPTSEE GENERAL CATALOG FOR ADDITIONAL DIMENSIONS OR ASK FOR CERTIFIED **inch / mmC*inch / mmBinch / mmAinch / mmHinch / mmWinch / mmLinch / mmSCR-60CE, SCRW-400 CEBVS-190 CEBVS-250 CEBVS-320 CEBVS-190CE, 250CE, 320 CEAPPLICATIONSM odel 2P-150CE on specially designed mountingbracket.
5 Vibration travel only into racks holdingPC-boards for greater plate 2P-100CE mounted to electrolesscopper TANKS for catalytic 2P-100CE mounted to top of speciallydesigned rack holder. Racks for PC-boards were putinto tank by SPWT-80CE solution tight vibrator assures100% vibration transfer to PC-boards PLATING IS POSSIBLE TO COMPLETELY PLATE THE PC-BOARDS WHEN USINGVIBCO S SPECIFIC VIBRATOR TECHNOLOGY AND RECOMMENDEDFLIGHT-BAR LOCATOR MOUNTING SYSTEM FOR BEST VIBRATIONTRANSFER & S APPLICATION ENGINEERS ARE AVAILABLETO VISIT YOUR PLANT AND HELP TO SOLVE YOURVIBRATION vibrator solved problem platingdouble sided holes in dia. holes in PC-board did not get SPRT-80CE vibrator placed in the middle ofthe flight bar locator to agitate the solutionsolved the , customer was using acompetitor vibrator. By using aVIBCO 2P-100CE vibrator onan adapter plate fitting an exist-ing mount customer decreaseda 30% rejection rate to almostzero.
6 Have a qualified VIBCO application engineer help youwith your vibrator , when tin PLATING the boards in the solutionair bubbles got trapped in the holes. SCR-100 CEvibrator mounted to the flight ball with its shaftvertically to obtain a gyratory motion removedthe 2003 VIBCO, Coast:Phoenix, Arizona 85254 Phone: (480) 596-1809(800) 633-0032 FAX:(480) 596-1614 Canada:2215 Dunwin DriveMississauga, 1X1 Phone: (905) 828-4191(800) 465-9709 FAX:(905) 828-5015 VIBCO, Stilson Road, Box 8 Wyoming, RI 02898E-Mail: (401) 539-2392 / (800) 633-0032 FAX: (401) 539-2584 2P-150CE used on single rack design for rinse cycleafter PC-Board drilling. 100% of drill burrs are series of 2P-150CE vibratorsused on robotic PLATING s allow VIBRATORS to operatewhen racks with PC-Boards areput into PLATING SPRT-80CE onseries of single TANKS .
