Victron DIY installation manual

1 [Type here] Rainbow Power Victron DIY Solar installation manual [Type here] Index Introduction Safety Scope of Delivery Additional Tools Required Product Description installation Requirements distribution board Solar Panels Array Wiring Batteries Electrical Connections Connection of Optional Accessories Inverter Battery Charger / Generator Commissioning Additional Information Technical Data Contact [Type here] Introduction The Rainbow Power Victron DIY Solar Systems are compact, do-it-yourself power systems.

2 These systems can energize a lot of small gear, including an efficient fridge. Suitable for low-consumption or infrequent electricity users. Ideal for remote sheds, beach huts, motor homes or weekenders. A Victron DIY Off-Grid System consists of a prewired wall-mountable distribution board complete with MPPT solar regulator, Circuit breaker referred to as CB. The system can be used on 12 or 24 volt battery banks up to 1000 AH, and can integrate a maximum of 4 x 260 watt solar panels (@ 12v) or 6 x 260 watt solar panels The board offers easy integration of a Victron Battery Voltage Monitor (BMV), battery charger and a DC/AC battery inverter (300w @ 12v, 700W @ 24V).

3 The distribution board comes Prewired with a 10 amp cigarette lighter socket, 2 x USB ports mm DC socket for lights and 40 amp Anderson Plug for Inverter. Safety The RPC Victron MPPT distribution board is an electrical device with potentially dangerous equipment. Care is required to protect yourself from injury. Read this section carefully and follow all safety precautions at all times. Please Take note of !Warning! throughout this guide. Please refer to your specified wiring diagram to ensure correct connection of all equipment.

4 Please Note Rainbow Power Co. takes no responsibility for any faults that occur due to incorrect connection or use of this equipment. If after reading this manual you have any questions relating to the installation or operation of your system please contact RPC on 02 6689 1430 [Type here] Danger to life due to Spark Hazard Operating damaged equipment can lead to hazardous situations that result in death or serious injuries due to spark hazards and resulting risk of fire. Only use equipment when it is technically faultless and in an operationally safe state.

5 Check the equipment for visible damage. Make sure that all external safety equipment is freely accessible at all times. Make sure that all safety equipment is in good working order. Danger to life due to explosive gases Explosive gases may escape from the battery and cause an explosion if ignited. This can result in death or serious injury. Protect the battery environment from open flames, embers or sparks. Install, operate and maintain the battery according to the manufacturer's specifications.

6 Do not heat the battery above the temperature permitted. Ensure that the battery room or enclosure is sufficiently ventilated. Chemical burns and poisoning due to battery electrolyte If handled inappropriately, electrolyte from the battery can burn the eyes, respiratory system and skin, and emit toxic fumes. This may result in blindness and serious chemical burns. Protect the battery enclosure against destruction. Do not open or deform the battery. Whenever working on the battery, wear suitable personal protective equipment such as rubber gloves, apron, rubber boots and goggles.

7 Rinse acid splashes thoroughly with clear water for a long time and consult a doctor. Install, operate, maintain and dispose of the battery according to the manufacturer's specifications. Spills can be neutralized with a mixture of Bi-Carbonated Soda and water Risk of injury due to short-circuit currents Short-circuit currents in the battery can cause heat build-up and electric arcs. Burns or eye injury due to flashes may result. Remove watches, rings and other metal objects. Use insulated tools.

8 Do not place tools or metal parts on the battery. Working at heights Climbing up the roof exposes you to the risk of falling off. A physical barrier (scaffolding) or a correctly supported safety harness is required whenever anyone climbs onto the roof. Lifting Injuries The batteries are heavy and should be moved using good lifting techniques. Keep back straight, Stomach muscles should be tightened and lifting should be done with your legs. [Type here] If they are too heavy to lift by one person then two people or mechanical lifting aids will be required [Type here] Scope of Delivery Your kit includes the following items RPC distribution board Solar Panels Battery Leads Battery Box Batteries Solar Cable Additional Tools Required Screw Driver Shifter Wire Cutters 20mm hole saw Multimeter [Type here]

9 Product Description Rainbow Power Victron DIY Solar consists The Rainbow Power MPPT Mini distribution board comes with: Victron MPPT solar controller 9 pole DC distribution box 1 x 63A DC CB Main battery - double pole 1 x 20A DC CB solar controller double pole 1 x 13A CB for Cigarette socket/USB socket 1 x 40A CB for Pluggable Inverter. 1 x 6A CB for DC Socket for Sundaya Ulita Lighting 1 x inline fuse for digital LED Voltmeter 1 x 40A CB for Battery charger Optional [Type here] Victron MPPT Solar Regulator The BlueSolar -MPPT charge controller is able to charge a lower nominal-voltage battery from a higher nominal voltage PV array, and is rated at max 100V open circuit voltage (on input).

10 Volt Meter The Led Voltmeter provides information regarding your battery voltage. This is useful in the operation of your system. Please refer to your Operation manual for further details. Battery Monitor (BMV) Optional High precision battery monitor from Victron Energy with the basic display options, such as voltage, current and ampere-hours consumed, the BMV-700 series also displays state of charge, time to go, and power consumption in watts. Inverter Victron Energy Phoenix Inverter 12V 300W or 24v 700W, with 230 volt AC output (standard AU/NZ outlet).