WATERBED ASSEMBLY INSTRUCTIONS - …

1 WARNING:Never leave any infant, or handicappedchild who cannot turn over, unattendedon this or any other adult or handicapped children can suf-focate in the face down position or getcaught between the mattress andframe, headboard or wall and : BUILD THE FRAMEP anel Headboard or No out your frame and hardware. Note that the footboardand backboard have grooved bottoms. The grooves shouldface in toward each other. Make sure all frame boards havefinished surfaces facing down on the your frame includes a headboard, attach it to the backframe board using the slats and screws provided. REMEMBER:The groove in the frame board must face inward once the head-board is the frame with the corner brackets and screwsprovided. Note the finished top to the frame is facing your assembled frame exactly where you want it inyour room. Now refer to Step 2 -- Building the ASSEMBLYINSTRUCTIONSWATERBED ASSEMBLYINSTRUCTIONSNOTE:Amattress pad and linens arevery important to your WATERBED .

2 Notonly will it make it more comfortable, butit stops the WATERBED from robbing youof natural body heat as well as soakingup normal body oils that can deteriorateyour mattress over dimensions 72W x 84L60W x 84L48W x 84 LExterior dimensions (panel ) 75W x 87L63W x 87L51W x 87 LExterior dimensions (bkcse. ) 75W x 93L63W x 93L51W x 93 LDECK-THE PEDESTALINTERNALSUPPORTSTHERMOSTATTHE MATTRESSTHE FRAMETHE SAFETYLINERTEMPERATURECONTROL PADCAPILLARYTUBESENSOR5 BOOKCASE out your frame and hardware. Note: The footboard andbackboard have grooved bottoms that should face inwardtoward each other. Also the finished side of the frame boardsshould face the the frame with the corner brackets and screws provided. Note that the side frame boards extend past thebackboard. The extended portion of the frame will support yourbookcase headboard. A sure way to insure correct internalspacing from head to foot is to use one of the deck boards (seeStep 2), as a measure.

3 Lay the 1 piece of deck into the grooveat the foot, now bring the head frame board in between the siderails until the deck fits in the groove. Mount at that point. Nowremove the deck board and go to Step 2 -- Building your assembled frame exactly where you want it in your room. This photo shows how the bookcase headboard willbe positioned on the extended frame AT A LATER TIME. DONOT MOUNT NOW! Refer to Step # POSTER out your frame, posts and hardware. Finished sides shouldface down toward floor exposing unfinished mounting the footboard to the two shorter posts using the bracketsandscrews provided. Some styles have hardware alreadymounted. Careful when mounting brackets to keep each bracketthe same portioned height on each frame board and the headboard and the frame backboard to the tallerposts also using the brackets and screws each side frame board to the posts attached to theheadboard and footboard.

4 Make sure the finished edges of theframe boards face your assembled frame where you want it in yourroom. Refer to Step 2 -- Building the 2: BUILDING THE PEDESTALS tandard out the pieces of your standard pedestal inside of theframe as pictured. The finished sides when assembled are toface the brown corner brackets on each corner of thepedestal. Slide the corner bracket on to each pedestal board atan angle, for easiest pressure is generally required to slide the corner bracketsall the way on and lock the corner into the two sets of the center support system, byinserting the slotted pieces into one another. Position the twointernal supports in the center of the pedestal, head to foot andside to side. You may receive a center support system of onelonger piece and two shorter pieces that are slotted. Positiondown the middle of the pedestal should be accurately centered within the framein its final , without letting it slide our of place, tilt the frame on to oneside.

5 Avoid moving the pedestal. After Step 3 you will lower theframe onto the deck boards which will be mounted on thepedestal. This does not apply to 4 poster beds. Build pedestal andposition deck boards inside of 4 poster frame, without moving : BUILDING THE PEDESTALSix Drawer one three drawer section of the pedestal inside theframe, recessed slightly on the side and at the head and foot aspictured. If you purchased a two drawer section pedestal, usethe same procedure as the three drawer that is the second three drawer section of the pedestal insidethe frame as 2: BUILDING THE PEDESTALSix Drawer Pedestal the wood pieces into the spaces between drawersections as pictured. For Queen size and Super Single sizewaterbeds the wood pieces may need to be cut down or not neededat all (hence push both three drawer sections tightly together.)

6 Certain the assembled six drawer pedestal is accuratelycentered within the frame in it s final , without letting it slide out of place, tilt the frame on to oneside. Avoid moving the pedestal. After Step 3 you will lower theframe onto the deck boards which will be mounted on the does not apply to the 4 poster beds. Position drawer sectionsand deck boards inside of 4 poster frame, without moving 2: BUILDING THE PEDESTALT welve Drawer directions for the Six Drawer Pedestal. Follow themexactly first. Next add the third three drawer section on top ofhalf of the completed six drawer pedestal. This procedure alsoworks for two drawer section the fourth three drawer section as the corners as accurately as possible, with specialcare given at the foot of the bed since it is most the wood pieces into the spaces between drawersections just as previously done for the bottom set of be certain that your twelve (or ten, eight drawer)pedestal is accurately positioned where you want it.

7 YOU WILLNOT BE ABLE TO MOVE IT ONCE THE BED IS , without letting it slide out of place, tilt the frame on to oneside. Avoid moving the pedestal. After Step 3 you will lower theframe onto the deck boards which will be mounted on the 3: LAY THE DECK BOARDS ON THE size - position the three 24 inch deck board pieces so thatthe pedestal is equally recessed on all sides. The cutcorners on the deck boards should be positioned at the four size - position the two 24 inch deck boards, with theone 12 inch deck board in the middle, so that the pedestal isequally recessed on all sides. The cut corners should be posi-tioned at the four Single size - position the two 24 inch deck boards so thatthe pedestal is equally recessed on all sides. The cut corners on thedeck boards should be positioned at the four : BUILDING THE PEDESTALC aptain s PedestalA.(Some Captain s Pedestals vary in configuration.)

8 If yoursneeds some sub- ASSEMBLY , do it prior to this step. Ask yoursleep consultant for more details.) Lay one of the larger drawersections inside the frame, recessed as the second large drawer ASSEMBLY sections inside, onthe other side of the frame, as , tilt the frame on to one side. Avoid moving the Step 3 you will lower the frame onto the deckboards which will be mounted on the ,slide in or attach the door section and wood pieces in theappropriate slots. These should be snug to assure proper certain the assembled Captain s Pedestal is accuratelycentered within the frame and in it s final position, beforemoving to Step 4: MOUNT THE FRAME TO THE the frame onto the deck. Make sure the grooves on thebottom of the footboard and backboard overlap the that the pedestal is centered and in photo shows how the grooves overlap the : Attach the L bracket into the middle of each frameboard and deck to secure the deck to the frame.

9 To protect linerand mattress from metal burrs, cover all inside metal bracketswith masking or duct your WATERBED features a bookcase headboard, mount it tothe frame now. Secure the headboard to the frame with the flatbrackets screwed in from underneath the headboard behind theframe. Slide the frame carefully away from the wall a fewinches, if needed, to allow more room to mount. Once mountedslide the frame back into final you purchased upholstered rail caps, attach them to yourframe now. The padded rail caps slip over the frame edges. At your option, you may wish to secure the caps onto the framewith screws, if 5: INSTALL HEATER UNITU nplug heater before filling or draining your WATERBED . Follow specificheater manufacturer s guidelines for detailed installation the heating pad in the center area of the deck avoid-ing the cracks in the deck boards. For Queen or Super Singleplace heating pad to one side or the other.

10 Do Not Place the thermostat control to either side of the frame,depending on where you will plug it in. Control unit may mountto side or underneath. See manufacturer s INSTRUCTIONS . Use thescrews provided. Securely plug the cord from the heating padinto the thermostat 5: INSTALL HEATER UNIT the thermostat control s sensor tube through the corner holeinside the frame onto the deck. The sensor tube should be posi-tioned midway between the frame and the heating pad, preferablytwelve inches away from the heating test the temperature control system, plug it in, turn thethermostat up and place your hand on the heating pad. As soonas you feel it start to warm up Unplug The Control From YourWall Socket! you purchased a massage unit, install it now. Since massageunits vary in installation, follow manufacturer s Not Place Unit On Top Of Heating Pad, Keep 6 From Pad!