(Wood beam not included) RACO Prestige Pocket and ...

1 (Wood beam not included). RACO Prestige Pocket and byparting prefinished aluminum door frames with track overhead (for wood doors only). Ball bearingtricyle roller with nylon wheelsfor quiet operation. RACO Pocket and byparting door frames feature trim and jamb extrusions PART NO. DESCRIPTION which have the same 9/32" standoff and 11/2" reveal as other RACO frames. Al- SL-1 Solid jamb, series 487, 9'2" lengths though load is not a factor, it is recom- SL-2 Trim for split jamb, 9'2" lengths mended that doors intended for Pocket SL-3A Support Track, 8'2" and 16'4" lengths; fits series 487 PR-1. application be ordered 15/6" thickness to SL-3S Closure plate with integral fascia strip, 8'2" lengths increase running clearance.

2 However, SL-4N Low-friction ball bearing roller with attachment screws 1314" doors can be used. RACO. SL-5 Pair of wood studs with floor bracket, 9' lengths Air-Core@ doors are recommended. SL-10 Rigid vinyl guide channel, 4 ft. lengths. The SL-3A track incorporates outboard R-2A fins which add strength, align the header (optional) Plywood bumper support (not included with assembly) assembly, and position the Pocket fram- R-23 Door bumper ing studs, SL-5. These studs are made of Pocket PRO Complete Prestige Pocket frame for doors to 4' x 9' spruce reinforced with 18 ga. steel chan- Pocket FSO Complete Freestanding Pocket frame for doors to 4' x 9' nels and are furnished with 14 ga.

3 Steel Bypart PRO Complete Prestige byparting frame for two doors 4' x 9' floor brackets. All jamb and header inter- Bypart FSO Complete Freestanding byparting frame for two doors sections are prefitted when complete 4' x 9' frames are ordered. 102 6. ---~-~---- (Wooden beam not included). l~ ~SL-3S. ~ - PR-1 Series 487..SL-5. D. II. I[. [. -SL-'. SL-2. D-' ". Recommended installation procedure: Gypsum board opening = 0-7/8". Freestanding type (ceiling height) Prestige type 1. Install SL-1 fixed jamb to top of frame. 1. Install SL-1 fixed jamb to bottom of PR-1 header. 2. Cut section of PR-1 header to door width less 1"; attach at head. 2. Install SL-3A track twice door width.]]

4 Run screws to wood beam Install SL-3A track twice door width. Run screws to wood beam each 12". Place SL-4N rollers in track. each 12". Place SL-4N rollers in track. 3. Install SL-5 wood studs at door opening plus '/a" and at midpoint of 3. Install SL-5 wood studs at door opening plus '/a" and at midpoint of Pocket engaging track and steel floor clips. Add SL-10 channel Pocket engaging track and steel floor clips. Add SL-10 channel and shoot to floor. Install R-23 bumper. and shoot to floor. Install R-23 bumper. 4. Place spreader in Pocket and attach gypsum board using laminat- 4. Place spreader in Pocket and attach gypsum board using laminat- ing adhesive plus screws.

5 Remove spreader. ing adhesive plus screws. Remove spreader. 5. Attach SL-2 Pocket trim mouldings using laminating adhesive. 5. Attach SL-2 Pocket trim mouldings using laminating adhesive. 6. Hand and adjust door. Install SL-3S closure plates to cover crack 6. Hang and adjust door. Install SL-3S closure plates to cover crack at top of door. at top of door. Note: Byparting frame is merely two opposing Pocket frames without fixed jambs. 6 103. PR-1. Series 487. Full height Pocket door application SL-4N. Less than ceiling height installation Additional parts required Pocket frame for doors to 4' wide: 1-Pc-SL-2, 9'2". 1-Pc-SL-2S, 9'2". 1-Pc-SL-7, wood spacer strip, 24".

6 Byparting frame for two 4' doors: 2-Pc-SL-2, 9'2". 2-Pc-SL-2S, 9'2". 2-Pc-SL-7, wood spacer strip, 24". Freestanding type (less than ceiling height). 1. Install SL-1 fixed jamb to top frame. 2. Install SL-3A track twice door width with rollers in place and with two 6" pieces of SL-7 each side of track over opening. Screw track to beam . 3. Follow steps 3, 4, 5 and 6 (left), except SL-2S is substituted for SL-3S. 103A.