500ma Output
Found 9 free book(s)ECUMASTER PMU-16/PMU-16DL Preliminary Manual
www.ecumaster.com+5V monitored 5V, 500mA output for powering external sensors INPUTS Page 6. Analog Inputs 16 inputs, 10 bit resolution, 0-5V (protected), with software selectable 10K Ohm pullup and pulldowns CAN Keypads 2 x Ecumaster keypads (4, 6, …
LT3045-1: 20V, 500mA, Ultralow Noise, - Analog Devices
www.analog.comOutput RMS Noise (Notes 4, 8) ILOAD = 500mA, BW = 10Hz to 100kHz, COUT = 10µF, CSET = 0.47µF, VOUT = 3.3V ILOAD = 500mA, BW = 10Hz to 100kHz, COUT = 10µF, CSET = 4.7µF, 1.3V ≤ VOUT ≤ 15V ILOAD = 500mA, BW = 10Hz to 100kHz, COUT = 10µF, CSET = 4.7µF, 0V ≤ VOUT < 1.3V 2.5 0.8 1.8 µVRMS µVRMS µVRMS Reference Current RMS Output Noise ...
LT3045 (Rev. C) - Analog Devices
www.analog.comOutput RMS Noise (Notes 4, 8) ILOAD = 500mA, BW = 10Hz to 100kHz, COUT = 10µF, CSET = 0.47µF, VOUT = 3.3V ILOAD = 500mA, BW = 10Hz to 100kHz, COUT = 10µF, CSET = 4.7µF, 1.3V ≤ VOUT ≤ 15V ILOAD = 500mA, BW = 10Hz to 100kHz, COUT = 10µF, CSET = 4.7µF, 0V ≤ VOUT < 1.3V 2.5 0.8 1.8 µVRMS µVRMS µVRMS Reference Current RMS Output Noise ...
Control4 EA-5 V2 Data Sheet
www.control4.comUSB port 1 USB 2.0 port—500mA Control IR out 8 IR out—5V 27mA max output, 1 IR blaster—front IR capture 1 IR receiver—front; 20-60 kHz Serial out 4 serial out (2 DB9 ports and 2 shared with IR out 1-2) Contact 4 contact sensors—2V-30VDC input, 12VDC 125mA maximum output Relay 4 relays—AC: 36V, 2A maximum voltage across relay;
2N2222 - Farnell
www.farnell.comIC = 500mA, VCE = 10V* 35 50 75 50 100 30 300-Dynamic Characteristics Transition Frequency ft IC = 20mA, VCE = 20V f = 100MHz 250 - MHz Output Capacitance Cob VCB = 10V, IE = 0 f = 100kHz - 8 pF Input Capacitance Cib VEB = 0.5V, IC = 0 f = 100kHz - 30 Switching Characteristics Delay Time td I C = 150mA,IB1 = 15mA - 10 ns Rise Time tr VCC = 30V ...
ALTERNATIVE 5W STEREO AUDIO AMPLIFIER - Diodes …
www.diodes.com• Alternative Output: Class -D or Class-AB • 5W Output at 10% THD with a 2Ω Load and 5V Power Supply at Class-D Mode • 3W Output at 10% THD with a 4Ω Load and 5V Power Supply • Filterless, Low Quiescent Current and No EMI • Low THD+N at Fully Output Range • Superior Low Noise • Efficiency up to 90% with Class-D Mode
DATASHEET
datasheets.raspberrypi.comOL Output low voltageb VDD IO = 3.3V, IOL = -2mA - - TBD V V OH Output high voltageb VDD IO = 3.3V, IOH = 2mA TBD - - V I OL Output low currentc VDD IO = 3.3V, VO = 0.4V TBD - - mA I OH Output high currentc VDD IO = 3.3V, VO = 2.3V TBD - - mA R PU Pullup resistor - TBD - TBD k R PD Pulldown resistor - TBD - TBD ka a Hysteresis enabled b Default ...
Building a DC-DC Step-Down (Buck) Converter Circuit Using ...
www.egr.msu.edudown to 9V output. The maximum output current that this voltage regulator can draw is 1A. However, under normal condition, the current that flows through the …
BC817-16LT1 - General Purpose Transistors NPN Silicon
www.onsemi.comOutput Capacitance (VCB = 10 V, f = 1.0 MHz) Cobo − 10 − pF Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions.