Manual - Curtis Instruments

The outline and mounting hole dimensions are shown in Figure 2. The controller should be mounted by means of the two mounting holes at the opposing corners of the heatsink, using M4 (#8) screws. Figure 2 Mounting Dimensions, Curtis 1212 and 1212P Controllers. Dimensions in millimeters and (inches)

  Dimensions

AC Motor Controller with VCL - Curtis Instruments

Together with the Curtis model 3141 CAN LCD display and the user-friendly Curtis Integrated Toolkit, the Curtis model AC F2-A is the ultimate Class III truck control system. FEATURES Fit for Purpose Compact, rugged housing with very small ‘footprint’ for its power rating. Heavy duty M6 busbars for motor and battery connectors.

  Controller, Toolkit, Motor, Motor controllers

AC Motor Controller and DC Pump System Controller

Together with the Curtis model 3141 CAN LCD display and the user-friendly Curtis Integrated Toolkit, the Curtis model AC F2-C is the ultimate Class III truck control system. FEATURES High efficiency, field-oriented motor control algorithms. Fully integrated Half-bridge hydraulic pump controller that is configurable for various hydraulic

  Toolkit

On-Road AC Motor Controller Model 1239E

Reverse polarity protection on battery connections. Short circuit protection on all output drivers. Thermal cutback, warning, and automatic shutdown provide protection to motor and controller. Rugged sealed housing and connectors meet IP65 environmental sealing standards for use in harsh environments. Meets or complies with relevant US

  Reserve, Protection, Battery

AC Induction Motor Controller Model 1234E - Curtis …

Motor Braking Torque c Category 2 ≥16 yrs ≥90% Model Battery Voltage Nominal (V) 2 Minute RMS Current Rating (A) S2–60 Min RMS Current Rating 1234E-23XX 24 350 175 1234E-52XX 36–48 275 140 1234E-53XX 36–48 350 175 1234E-62XX 48–80 250 110 Contact Curtis to obtain the VCL Vehicle Control Language compiler and development tools.

  Development, Model, Braking

SERIES - Curtis Instruments

6 5 display position encoder b+ u v w b– main j1-31 j1-32 j1-7 j1-26 i/o gnd phase a phase b 1 2 4 3 ac motor switch 16 j1-19 digital driver 6 em rev. load hold valve lower lift mode motor temp. input t +12v (100ma) +5v (100ma) emergency stop wiring diagram 1232 ac induction motor controller pump cont digital driver 7 j1-20 j1-30 analog out ...

Models 1204M/05M/09M/21M - Curtis Instruments

aluminum extruded housing. 3 Simple mounting and wiring with push-on connectors for control signals. 3 Plated solid copper buses used for all power connections. 3 Thermal protection and compensation circuit provides ... (#18 AWG) vinyl insulated stranded wire

  Aluminum, Stranded

AC Induction Motor Controllers - Curtis Instruments

forward reverse throttle pot pot 2 pv driver j1-2 can term h j1-21 j1-34 can term l short for 120 pot 2 ohm termination high j1-27 prop. valve 8 6 5 display speed encoder b+ u v w b– main j1-31 j1-32 j1-7 +5 v j1-26 i/o gnd phase a phase b 1 2 4 3 ac motor j1-19 digital output 7 j1-20 digital output 6 emr check (optional) em rev. mode motor ...

  Phases, Drivers, Forward

This document contains BOTH the - Curtis Instruments

Paste, Drag & Drop). BATTERIES A compartment on the back holds two AA sized batteries. The batteries keep the real-time clock running and are used to power the 1313 HHP when working offline. Although the batteries can be used to power the 1313 while connected to a controller, operations such as data logging may quickly deplete the batteries.

  Septa

Sigma Spectrum Service Manual - Frank's Hospital Workshop

install the clamp on the pump. The dimension of the clamp is less than 7.0” long X2.5” wide. The weight of the clamp is less than 1.2 lbs. CAUTION: Always operate the pump in vertical direction with the key hole at the top of the pump. Tubing Channel/Pump Door The tubing channel consists of Proximal air/occlusion sensor

  Pumps

SERIES - Curtis Instruments

A range of controllers (inverters) for the speed and torque control of 3-phase AC motors. Intended for use as electric traction or hydraulic pump motor controllers for mobile, on-vehicle applications that use a 24-96 VDC nominal battery supply. 1232 1234 1236 SERIES SERIESLogos Curtis MarCom 2014 Model 1232SE Model 1236SE Model 1234SE Model 1238SE

  Controller, Pumps

CompactLogix 5380 with Dual IP Configuration

Stratix Switch Family PanelView™ 5500 • High speed backplane of packet transfer rate of 4.4ms (511 byte packet) 5069 Compact I/O Performance • Supports 1-Gb embedded switch technology for Device Level Ring, Linear and Star topologies • 31 I/O Modules in a …

  Switch, Transfer, Compactlogix

1785-6.1, PLC-5 Programmable Controllers Instruction Set ...

detecting when a limit switch closes bit level changing the temperature preset element level transfer analog data block transfer turn on a motor 10 seconds after a pump is activated timing move 1 of 3 recipes into a work area multi-element keep track of parts as they move from station to station shifting keep track of total parts in a bin counting

  Controller, Switch, Pumps, Instructions, Transfer, Controllers instruction

Residential/Commercial Generator Sets - Kohler Co.

TableofContents,continued Table of Contents TP-6804 2/21 Section3 RDC2ControllerOperation ..... 35 3.1 RDC2 Generator Set/Transfer Switch Controller 35

  Switch, Transfer, Transfer switch

UNIT-I Automobile electrical and electronics Electrical ...

Edc pump actuator Electro-magnetic actuators are usually located on the fuel pump to transfer electrical signals into mechanical action in this case fuel rack actuator and or fuel stop solenoid which means that depending on requests from control unit full fuel or no fuel quantity. Injectors Boost-pressure actuator Intake-duct switchoff

  Pumps, Transfer

GENERAL ELECTRICAL NOTES - Community College of …

disconnect switch - size as indicated on plans size (amps) 30/2/20/3r no. of poles nema rating (if other than 1) e duplex receptacle, 20a, 120v, 18"aff, uon. subscript "e" denotes receptacle on emergency power. emergency receptacle shall be red. motor connection. combination motor starter and disconnect switch, mount within site of motor 5'-0 ...

  Switch