AN10441 Level shifting techniques in I2C-bus design

Document information AN10441 Level shifting techniques in I2C-bus design Rev. 01 — 18 June 2007 Application note Info Content Keywords I2C-bus, level shifting Abstract Logic level shifting may be required when interfacing legacy devices with

  Notes, Applications, Levels, Technique, Shifting, Application note, An10441 level shifting techniques in, An10441

AN3234: Washing Machine Three-Phase AC …

Washing Machine Three-Phase AC Induction Motor Drive, Rev. 0 Indirect Vector Control 4 Freescale Semiconductor If you are looking for more theory on the field ...

  Machine, Washing, Washing machine

1. General description - nxp.com

1. General description The TJA1044 is part of the Mantis family of high-speed CAN transceivers. It provides an interface between a Controller Area Network (CAN) protocol controller and the physical

  General, Descriptions, General description, General description nxp

PCA9570 Remote 4-bit general purpose outputs for 1 MHz …

1. General description The PCA9570 is a CMOS device that provides 4 bits of General Purpose parallel Output (GPO) expansion in low voltage processor and handheld battery powered mobile

  General, Purpose, Remote, Output, General purpose, Pca9570 remote 4 bit general purpose outputs for, Pca9570

P82B96 Dual bidirectional bus buffer - nxp.com

1. General description The P82B96 is a bipolar IC that creates a non-latching, bidirectional, logic interface between the normal I2C-bus and a range of other bus configurations.It can interface

S32K144 EVB Quick Start Guide - NXP Semiconductors

J14 SWD connector. 3 EXTERNAL USE S32K144 EVBFeatures: ... USB connector of the USB cable to micro-B port J7 on the S32K144EVB. ... Windows, Linux and Mac operating systems. Using the MSD Flash Programmer 1. Locate the .srec file of your project , file is under the

Three-Phase BLDC Motor Sensorless Control Using …

This document describes the design of a three-phase brushless DC motor (BLDC motor) drive based on Freescale’s MC56F8013 and MC56F8023 dedicated motor control device. Brushless DC motors are popular in a wide application area.

  Phases, Using, Control, Motor, Three, Sensorless, Brushless, Brushless dc, Three phase brushless dc, Motor sensorless control using

AN11443 BFU550XR ISM 433 MHz LNA design - nxp.com

AN11443 BFU550XR ISM 433 MHz LNA design Rev. 1 — 23 January 2014 Application note . Document information Info Content Keywords BFU520, BFU530, BFU550 series, ISM-band, 433MHz 866MHz Abstract This document describes an ISM Frequency LNA design on BFU5xxXR Starter kit

  433 mhz, 433mhz

DSP56156 16-Bit Digital Signal Processor - nxp.com

The DSP56156 is a general-purpose MPU-style Digital Signal Processor (DSP). On a single semi- conductor chip, the DSP56156 comprises a very efficient 16-bit digital signal processing core, pro-

  Processor, Processing, Signal, Digital, Digital signal processing, Digital signal processor

SAA7706H Car radio Digital Signal Processor (DSP)

Car radio Digital Signal Processor (DSP) SAA7706H This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in

  Processor, Radio, Signal, Digital, Car radio digital signal processor

Application Note Slave Controller - Beckhoff Automation

Slave Controller – Application Note PHY Selection Guide 1 1 Overview An EtherCAT Slave Controller (ESC) takes care of the EtherCAT communication as an interface between the EtherCAT fieldbus (Ethernet) and the slave application. EtherCAT uses 100Mbit/s full duplex Ethernet communication. EtherCAT G uses 1,000Mbit/s full duplex

  Notes, Applications, Controller, Slave, Application note, Slave controller, Application note slave controller, Slave application

Interfacing to High Speed ADCs via SPI - Analog Devices

This application note describes how to use the serial peripheral interface ( SPI) port on Analog Devices, Inc., high speed converters . In addition, this application note defines the electrical, timing, and procedural requirements for interfacing to these devices. The implementation is compatible with industry -standard SPI

  Notes, Devices, Applications, Analog devices, Analog, Application note

SMBus Quick Start Guide - NXP

• A slave is a device that receives or responds to a command. A system may not include a host. For example, a simple battery charging system is a hostless system. In an SMBus system, a device can be master only, slave only, or it may act as a slave most of the time, but in special instances it becomes a master. Table 3. Reserved SMBus addresses 1

  Guide, Quick, Start, Smbus, Slave, Smbus quick start guide

SSI Synchronous Serial Interface Master - Application Note

APPLICATION NOTE 2013-11-08 6/26 Art.No. 10021488 1. SSI Theory Synchronous Serial Interface (SSI) is a widely used serial interface standard for industrial applications especially, rotary encoders. It is a point-to-point connection from a master (e.g. PLC, microcontroller or other control systems) to a slave (e.g. the rotary encoder).

  Notes, Applications, Slave, Application note

AN4776 Application note - STMicroelectronics

Application note General-purpose timer cookbook for STM32 microcontrollers Introduction The timer peripheral is part of the essential set of peripherals embedded in all the STM32 microcontrollers. The number of timer peripherals and their respective features differ from ... The master/slave controller unit of the slave timer is configured to ...

  Notes, Applications, Controller, Slave, Application note, Slave controller

SPI Configuration and Flash Programming in UltraScale ...

application note, SPI operates in a full duplex mode sending commands and addresses from the master over the master-output, slave-input (MOSI) line and receiving data over the master-input, slave-output (MISO) line. Data is synchronous with an SPI clock (SCLK) signal, and the slave device is selected via an SPI select (SS#) signal.

  Notes, Applications, Slave, Application note