HE784 - AQUA-BLOC® WB - henry.com

Limited Warranty We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product - such as weather, workmanship, equipment utilized and prior condition of the substrate - are

TECHNICAL DATA SHEET

REVISION: 11/17/15 Henry Company, 999 N. Sepulveda Blvd., Ste. 800, El Segundo, CA 90245 Technical Services - Phone: (800) 486-1278 – Email: techservices@henry.com www.henry.com Henry CM100 Fast Curing, Elastomeric Fluid Membrane Uses Henry CM100 may be used as a waterproofing and roofing membrane on horizontal or vertical surfaces. Ideal alternative to hot

  Ideal

Henry Blueskin VP160 Air Barrier System Installation Manual

3 1. Introduction This installation manual includes materials and installation procedures for Henry® Blueskin® VP160 Self-Adhered Water Resistive Air Barrier system. Blueskin® VP160 meets the current IBC and IECC air barrier requirements for a water resistive barrier (WRB) as referenced in ICC ESR-2975.

  Installation, Water, Resistive, Water resistive, Water resistive air

TECHNICAL DATA SHEET - Henry

Air Permeance - Material @1.57psf (75Pa) 0.0001 cfm/ft² (0.0005 L/[sec-m²]) ASTM E2178 Air Leakage - Assembly Pass ASTM E2357 Elongation 250% ASTM D412 Tensile Strength 140 psi (965 kPa) ASTM D412 Flame Spread Index 10, Class A ASTM E84 Smoke Developed 15, Class A ASTM E84 Fire Testing Complies with NFPA 285 in various wall

  Sheet, Data, Testing, Technical, Technical data sheet, Leakage, Air leakage

Henry 925 BES Sealant

Henry® 925 BES Sealant is a premium, moisture cure sealant for construction joints subject to dynamic joint movement. This one-part, low odor, moisture cure product provides excellent weathering resistance, flexibility, very low VOC, through use of a silyl-terminated polyether (STPE) polymer. Upon curing, it is paintable with latex based paints.

  Product, Sealant

TECHNICAL DATA SHEET - Henry

cast-in-place concrete, concrete block, steel, aluminum and galvanized metal. Strike masonry joints full-flush. Concrete surfaces must be smooth and without large voids, spalled areas or sharp protrusions. Concrete must be cured a minimum of 14 days. Curing

  Sheet, Data, Technical, Steel, Technical data sheet, Galvanized

Air-Bloc All Weather STPE

Henry® Air-Bloc All-Weather STPE is a low VOC, UV and fire-resistant fluid applied, elastomeric membrane designed to provide a vapor permeable, water resistive air barrier when applied to above-grade wall assemblies. It is single-component, moisture cure

  Water, Step, Weather, Resistive, Water resistive air, All weather stpe

TECHNICAL DATA SHEET Blueskin WP200 - Henry

REVISION: 02/27/17 Henry Company 999 N. Sepulveda, Ste 800, El Segundo CA 90245-2754 Technical Services- Phone (800) 486-1278 – Email: techservices@henry.com www.henry.com Blueskin WP 200 Self-Adhesive Waterproofing Membrane Uses Blueskin WP200 is designed for use as a self-adhered s heet waterproofing membrane in above or below grade applications.

  Sheet, Data, Data sheet, Heet, Sh eet

Air & Water Barrier Membrane - Henry

Concrete . ASTM C836 load suction pressure-Low Temperature Flexibility and Crack Bridging @ –20°C . ASTM C836 -Aging-Long Term Flexibility . CGSB 71 -GP-24M -Nail Sealability . ASTM D1970 --Resistance to Mold, Mildew & Fungal growth . ASTM D5590 . ASTM E84-VOC Content . Gray . 60% . 10.8 lbs/gal (1.3 kg/l) 2 Hours to touch dry . 24 Hours to ...

  Concrete, Nail

WATERPROOFING SYSTEMS - Henry

Secondary Containment Structures • Tunnels • Underground ... Drainage & Irrigation Channels • Potable Water Reserves • Seals Embedded Steel, PVC or HDPE Pipe Penetrations HENRY DRAINAGE COMPOSITES: A BETTER ENGINEERED SOLUTION FOR MANAGING THE FLOW OF WATER ... highway drainage systems.

  System, Underground, Drainage, Drainage systems

Extruded Polystyrene (XPS) Rigid Foam Insulation Product ...

Product Data Sheet FOAMULAR® 250 Extruded Polystyrene (XPS) Rigid Foam Insulation • Provides a weather resistant barrier (when joints are sealed) to enhance the building’s resistance to air and moisture penetration Technical Information This product is combustible. A protective barrier or thermal barrier is required as specifi ed

  Information, Product, Technical, Polystyrene, Technical information, Insulation, Extruded, Extruded polystyrene, Insulation products

Extruded Polystyrene (XPS) Rigid Foam Insulation Product ...

Product Data Sheet FOAMULAR® 150 Extruded Polystyrene (XPS) Rigid Foam Insulation • Provides a weather resistant barrier (when joints are sealed) to enhance the building resistance to air and moisture penetration. Technical Information This product is combustible. A protective barrier or thermal barrier is required as specifi ed

  Information, Product, Technical, Technical information, Insulation, Insulation products

TECHNICAL GUIDE - Georgia-Pacific Building Products

Dec 01, 2017 · For latest information and updates: Technical Service Hotline 1.800.225.6119 or www.gpgypsum.com CAUTION: For product fire, safety and use information, ... DensDeck Roof Board serving as an insulation thermal barrier overlayment with all joints staggered a min. of 6” (152 mm) from the plywood joints.

  Information, Product, Technical, Pacific, Building, Board, Georgia, Insulation, Georgia pacific building products

Product Information Sheet Froth-Pak Insulation Spray Foam

Product Theoretical Yield, (1) board ft Kits ... * Froth-Pak™ Foam Insulation is a former product of The Dow Chemical Company. ** Actual cure time will depend on temperature, foam thickness, the specific nozzle used, etc. Product Information Sheet.

  Information, Product, Sheet, Board, Insulation, Product information sheet

POLYISOCYANURATE FOAM SHEATHING CONTINUOUS …

Technical specifications as shown in this literature are intended to be used as general guidelines only. Please refer to the Safety Data Sheet and product label prior to using this product. The physical and chemical properties of AP Foil-Faced Polyisocyanurate Continuous Insulation listed herein represent typical, average values ob-

  Product, Technical, Insulation

AP Foil-Faced - Johns Manville

Technical specifications as shown in this literature are intended to be used as general guidelines only. Please refer to the Safety Data Sheet and product label prior to using this product. The physical and chemical properties of AP Foil-Faced Polyisocyanurate Continuous Insulation listed herein represent typical, average values ob -

  Product, Technical, Insulation

Thermafiber SAFB Mineral Wool Insulation

Thermafiber Insolutions® offers industry leading technical and engineering assistance to architects, specifiers, and contractors. These services include CAD drawings, engineering judgments, LEED® Credit Information, and product recommendations. Contact our technical services department at 1-888-834-2371 or email

  Information, Product, Technical, Insulation