CAN-Bus Troubleshooting Guide

transceivers. For a voltage lower than 2.0 V please check CAN_H and CAN_L conductors for continuity. For a voltage higher than 4.0 V, please check for excessive voltage. To find the node with a faulty transceiver please te st the CAN transceiver resistance (see next page). 1.3 Ground The shield of the CAN network has to be grounded at only one ...

  Guide, Troubleshooting, Transceiver, Troubleshooting guide

Low Power, 3.3 V, RS-232 Line Drivers/Receivers ADM3202 ...

The ADM3202/ADM3222/ADM1385 transceivers are high speed, 2-channel RS-232/V.28 interface devices that operate from a single 3.3 V power supply. Low power consumption and a shutdown facility (ADM3222/ADM1385) make them ideal for battery-powered portable instruments.

  Transceiver

LTC2870/LTC2871 – RS232/RS485 Multiprotocol Transceivers ...

VCC = VL = 3.3V, TE485 = 0V, LB = 0V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Power Supply VCC Supply Voltage Operating Range 3 5.5 V VL Logic Supply Voltage Operating Range VL ≤ VCC 1.7 VCC V VCC Supply Current in Shutdown Mode RXEN = VL, DXEN = TE485 = FEN = 0V, (LTC2870) DX485 = DX232 = …

  Transceiver

MAX3160/MAX3161/MAX3162 +3.0V to+5.5V, 1µA, RS-232/ …

MAX3160/MAX3161/MAX3162 +3.0V to+5.5V, 1µA, RS-232/ RS-485/422 Multiprotocol Transceivers EVALUATION KIT AVAILABLE General Description The MAX3160/MAX3161/MAX3162 are …

  Transceiver

D C a n d A C S w i t c h i n g C h a r a c t e r i s t i ...

I/O supply voltage for the high-bandwidth memory –0.300 1.500 V V. CCAUX_HBM. Auxiliary supply voltage for the high-bandwidth memory –0.300 3.000 V GTY or GTM Transceiver. 7. V. CCINT_GT. Digital supply voltage for select modules in the GTM transceivers –0.500 1.000 V V. MGTAVCC. Analog supply voltage for transceiver circuits –0.500 1 ...

  Transceiver, A n c

SA612A Double-balanced mixer and oscillator

3. Applications Cordless telephone Portable radio VHF transceivers RF data links Sonobuoys Communications receivers Broadband LANs HF and VHF frequency conversion Cellular radio mixer/oscillator SA612A Double-balanced mixer and oscillator Rev. 3 …

  Balanced, Double, Transceiver, Mixers, Double balanced mixer

MAX3222/MAX3232/MAX3237/MAX3241 - 3.0V to 5.5V, Low …

Input Voltage Range -25 25 V Input Threshold Low TA = +25°C VCC = 3.3V 0.6 1.2 V VCC = 5.0V 0.8 1.5 Input Threshold High TA = +25°C VCC = 3.3V 1.5 2.4 V VCC = 5.0V 1.8 2.4 Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and ...

Checking Port Status and Connectivity

You can have up to eight simultaneous Telnet sessions. Before you can open a Telnet sessio n to the switch, you must first set the IP address (and in some cases the default gateway) for the switch. For information about setting the IP address and default gateway, see Chapter 3, “Configuring the Switch for the First Time.”

  Connectivity, Status, Ports, Checking, Checking port status and connectivity

3 A, Low V , Low Noise, CMOS Linear Regulator Data Sheet ...

1.6 V to 3.6 V 2 A Fixed/adjustable 16-lead LFCSP ADP1752/ ADP1753 1.6 V to 3.6 V 0.8 A Fixed/adjustable 16-lead LFCSP ADP1754/ ADP1755 1.6 V to 3.6 V 1.2 A Fixed/adjustable 16-lead LFCSP The ADP1763 is available in fixed output voltages ranging from 0.9 V to 1.5 V. The output of the adjustable output model can

Kintex-7 FPGAs Data Sheet: DC and AC Switching ... - Xilinx

Kintex-7 FPGAs Data Sheet: DC and AC Switching Characteristics DS182 (v2.19) March 26, 2021 www.xilinx.com Product Specification 4 Table 3: DC Characteristics Over Recommended Operating Conditions Symbol Description Min Typ(1) Max Units VDRINT Data retention VCCINT voltage (below which configuration data might be lost) 0.75 – – V VDRI Data retention …

  Xilinx