Chip Resistor
Found 9 free book(s)SURFACE MOUNT RESISTORS TECHNICAL GUIDE Ver
www.mouser.comchip resistor (by kind) are shown in Fig.8. Fig.8. System figure of thick-film chip resistor The range of resistance value and TCR of thin-film chip resistor (by kind) are shown in Fig.9. Fig.9. System figure of thin-film chip resistor The range of resistance value and TCR of thin-film chip resistor (by kind) are shown in Fig.10. Fig.10.
USB to serial chip CH340 - SparkFun Electronics
cdn.sparkfun.comresistor internal, low level is SIR infrared serial interface, high level is common serial interface CKO. OUT(NC.) CH340T: clock output 1 NC CH340R:unconnected, must be suspend 5. Function description CH340 chip set up USB pull-up resistor internal, UD+ and UD- pins must be connected to USB bus directly.
Future Technology Devices International Ltd FT232R USB ...
www.ftdichip.comSingle chip USB to asynchronous serial data transfer interface. Entire USB protocol handled on the chip . No USB specific firmware programming required. Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration. Fully integrated USB termination resistors.
Altera DE0 Board - Intel
www.intel.comOne 8-Mbyte Single Data Rate Synchronous Dynamic RAM memory chip Supports 16-bits data bus Flash memory 4-Mbyte NOR Flash memory Support Byte (8-bits)/Word (16-bits) mode ... Uses a 4-bit resistor-network DAC With 15-pin high-density D-sub connector Supports up to 1280x1024 at 60-Hz refresh rate . DE0 User Manual 7
cp2102rev1 0 - SparkFun Electronics
www.sparkfun.comOption 1: A 4.7 kΩ pull-up resistor can be added to increase noise immunity. Option 2: A 4.7 µF tantalum capacitor can be added if powering other devices from the on-chip regulator. Option 3: Avalanche transient voltage suppression diodes should be added for ESD protection. Option 3: Use Littlefuse p/n SP0503BAHT or equivalent. 1 CP2102 ...
www.i-enet
cdn-shop.adafruit.comand power reverse polarity, series a not more than 100ohm resistor at the po-wer supply pin(VDD). The capac-itance 104 as bypass capacitor. To prevent the reflection and hot-swap protection, we suggest to connect a 33 ohm resistor at the data input or output port for impedance. 2.power supply is 12V with 3 LED and constant current(18.5mA ...
USB hardware and PCB guidelines using STM32 MCUs ...
www.st.comPull-up resistor on USB_DP line Embedded 1.5 kΩ resistor should be added LPM X - X BCD X - ADP - 1. X: supported. 2. Bidirectional, including EP0. 3. When the CAN peripheral is used, only the first 768 bytes are available to USB, the last 256 Bytes are used by CAN. 4.
ES9038Q2M 32-Bit Stereo Low Power Audio DAC Analog ...
www.esstech.com• In reset state, a 120k ohm resistor connects between SW and GPIO2 allowing GPIO2 to switch input of SABRE9602. See Register 39: General Configuration 2 for more information. 17 GPIO1 I/O Tri-stated General purpose input/output pin 1, or SPDIF Input 4. 18 DATA2 I Tri-stated DSD Data2 (R) or PCM Data CH1/CH2 or SPDIF Input 2 19 DATA1 I/O Tri ...
CAT4016 - 16-Channel Constant Current LED Driver
www.onsemi.comcurrents are programmed together via an external RSET resistor. Low output voltage operation on the LED channels as low as 0.4 V (for 2 to 100 mA LED current) allows for more power efficient designs. A high−speed 4−wire serial interface of up to 25 MHz clock frequency controls each individual channel using a shift register and latch ...