I2c Compatible 2 Wire Serial
Found 12 free book(s)I2C-Compatible (2-wire) Serial EEPROM
ww1.microchip.comI2C Compatible (2-wire) Serial Interface Schmitt Trigger, Filtered Inputs for Noise Suppression Bidirectional Data Transfer Protocol 400kHz (1.7V) and 1MHz (2.5V, 2.7V, 5.0V) Compatibility Write Protect Pin for Hardware Data Protection 8-byte Page Write Mode ̶Partial Page Writes Allowed Self-timed Write Cycle (5ms max)
24AA64/24LC64 64K I2C Serial EEPROM
ww1.microchip.com• 2-wire serial interface bus, I2C™ compatible • Cascadable for up to eight devices • Schmitt Trigger inputs for noise suppression • Output slope control to eliminate ground bounce • 100 kHz (24AA64) and 400 kHz (24LC64) com-patibility • Self-timed write cycle (including auto-erase) • …
24AA512/24LC512/24FC512 512K I2C Serial EEPROM Data …
ww1.microchip.comJan 05, 2010 · • 2-Wire Serial Interface, I2C™ Compatible • Cascadable for up to Eight Devices • Schmitt Trigger Inputs for Noise Suppression • Output Slope Control to Eliminate Ground Bounce • 100 kHz and 400 kHz Clock Compatibility • Page Write Time 5 …
Lidar Lite v3 Operation Manual 2 and Technical Specifications
static.garmin.comI2C Interface This device has a 2-wire, I2C-compatible serial interface (refer to I2C-Bus Specification, Version 2.1, January 2000, available from Philips Semiconductor). It can be connected to an I2C bus as a slave device, under the control of an I2C master device. It supports 400 kHz Fast Mode data transfer.
THE I2C-BUS SPECIFICATION VERSION 2.1 JANUARY 2000 - …
i2c2p.twibright.com2.2 Manufacturer benefits I2C-bus compatible ICs don’t only assist designers, they also give a wide range of benefits to equipment manufacturers because: •The simple 2-wire serial I2C-bus minimizes interconnections so ICs have fewer pins and there are not so many PCB tracks; result - smaller and less expensive PCBs
Marvell 88SE9220/9230/9235/9215 - Marvell Technology, Inc.
www.marvell.comEnclosure Management I2C support Two-Wire Serial Interface (TWSI) Interface for external EEPROM containing configuration information ... and xSATA at 6 Gb/s and are backward compatible to 1.5 Gb/s and 3 Gb/s. Built-in support for SATA Port Multipliers with ... PCIe 2.0 x 2 Flash ROM Marvell Two to Four 88SE92xx SATA HDDs or SSDs Marvell ...
3-Axis Digital Compass IC HMC5883L - Adafruit Industries
cdn-shop.adafruit.comCompatible for Battery Powered ApplicationsLow Voltage Operations (2.16 to 3.6V) and Low Power Consumption (100 μA) Built-In Strap Drive Circuits Set/Reset and Offset Strap Drivers for Degaussing, Self Test, and Offset Compensation I 2C Digital Interface Popular Two-Wire Serial Data Interface for Consumer Electronics
18-Bit ADC with I2C Interface and Onboard Reference
ww1.microchip.comMar 26, 2009 · The on-board precision 2.048V reference voltage enables an input range of ±2.048V differentially (Δvoltage = 4.096V). The device uses a two-wire I2C compatible serial interface and operates from a single 2.7V to 5.5V power supply. The MCP3421 device performs conversion at rates of 3.75, 15, 60, or 240 samples per second (SPS)
64-Kbit serial I²C bus EEPROM - STMicroelectronics
www.st.com2.2 Serial Data (SDA) SDA is an input/output used to transfer data in or data out of the device. SDA(out) is an open drain output that may be wire-OR’ed with other open drain or open collector signals on the bus. A pull-up resistor must be connected from Serial Data (SDA) to …
16-Kbit serial I2C bus EEPROM - STMicroelectronics
www.st.comJul 10, 2013 · 2.2 Serial data (SDA) SDA is an input/output used to transfer data in or data out of the device. SDA(out) is an open drain output that may be wire-OR'ed with other open drain or open collector signals on the bus. A pull-up resistor must be connected from serial data (SDA) to VCC (Figure 11 indicates how to calculate the value of the pull-up ...
USB Type-C System Overview
www.usb.orgUSB 3.2 / USB4™ TXp1, TXn1 RXp1, RXn1 TXp2, TXn2 RXp2, RXn2 SuperSpeed USB / USB4 serial data interface: one transmit diff pair and one receive diff pair per lane Two pin sets to enable x2 operation USB 2.0 Dp1, Dn1 Dp2, Dn2 USB 2.0 serial data interface Two pin sets, one wire set to enable plug flipping Configuration CC1, CC2 (receptacle) CC ...
CircuitPython Essentials - Adafruit Industries
cdn-learn.adafruit.comDec 12, 2021 · i2c = busio.I2C(board.SCL, board.SDA) Then, you pass the I2C object to a driver for the hardware you're using. For example, if you were using the TSL2591 light sensor and its CircuitPython library, the next line of code would be: tsl2591 = adafruit_tsl2591.TSL2591(i2c) However, CircuitPython makes this simpler by including the I2C singleton in ...