S. L. ten Cate 08-2015

2” x 4,5 UNC 50,726 44,679 4,5 UNF (2A) Nominal Diameter Major Diameter (mm) Minor Diameter (mm) TPI 1/4” x 28 UNF 6,325 5,360 28 5/16” x 24 UNF 7,910 6,782 24 3/8” x 24 UNF 9,497 8,382 24 7/16” x 20 UNF 11,079 9,728 20 1/2” x 20 UNF 12,667 11,328 20 5/8” x 18 UNF 15,839 14,351 18 3/4” x 16 UNF 19,012 17,323 16 7/8” x 14 UNF ...

  2015, 5 02

Thread and Connector Identification

inch - TPI mm inch mm inch inch 5/16 - 24 UNF-05 7,9 0.31 6,9 0.27 1/8 3/8 - 24 UNF-06 9,5 0.38 8,5 0.33 3/16 7/16 - 20 UNF-07 11,1 0.44 9,9 0.39 1/4 1/2 - 20 UNF-08 12,7 0.50 11,4 0.45 5/16 9/16 - 18 UNF-09 14,3 0.56 13,0 0.51 3/8 3/4 - 16 UNF-12 19,1 0.75 17,5 0.69 1/2 7/8 - 14 UNF-14 22,2 0.88 20,3 0.80 5/8 1.1/16 - 12 UN-17 27,0 1.06 24,9 0 ...

  Identification, Thread, Connectors, Thread and connector identification

ICC-ES Evaluation Report ESR-3223

#12-14 HWH #12-14 UPFH 1/ 4-14 HWH 1/ 4-20 HWH or SI: 1 inch = 2 For shear conne spectively, mus Nominal strength Steel must comp o calculate LRF he “–” symbol d he top sheet is FIGURE ost Widely Acc TA N NOM DIAM (in H 0.1 H 0.2 H 0.2 0.2 0.2 5.4 mm, 1 lbf = 4 ections, the low design. s are based on ly with AISI S10 D values, multip ...

  Evaluation, Icc es evaluation

BAB I PENDAHULUAN 1.1 Latar Belakang

1. Ron Akek Mesin boat 5 Pk 10 unit 10 orang Dusun Pogari 2. Surak Sita Mesin boat 5 Pk 14 unit 14 orang Dusun Adduru 3. Rop Akek Mesin boat 5 Pk 10 unit 10 orang Dusun Pogari Sumber: Dinas Perikanan Kepulauan Mentawai 2017 Dari tabel di atas dapat dilihat penerimaan bantuan program perikanan

Shear Strengths Comparison Grades 2, 5 & 8

Shear Strengths Comparison Grades 2, 5 & 8 Comparison of Shear Strengths of Grade 2, 5 and 8 Screws The industry standard for determining shear strengths of fasteners is to take 60% of the minimum Ultimate Tensile Strength of the fastener for …

Standard Specification for Anchor Bolts, Steel, 36, 55, and ...

5.1.4 Grade and class. 5.1.5 Copper content, if copper bearing steel is required. 5.1.6 Size and Dimensions—Nominal diameter and thread pitch, bolt length, thread length, head type (if required) and hook angle and hook length (if required). 5.1.7 Coatings—If required, the coating process and the length to be coated as measured from the ...