Optimization of Sand Casting Process Parameter …

Casting defects have been selected as the most representative quality characteristics in the ... Maximizing η’ leads to minimization of quality loss due to defects.

  Defects, Casting, Minimization, Casting defects

Design of High Gain Two stage Op-Amp using …

The Operational Amplifier (Op-Amp) is designed and analyzed by using Cadence ICFB full custom design suite using 90nm technology. The ...

  Operational, Amplifier, Operational amplifier

Numerical Study of Knife Edge Effects in Flash Riveted ...

about knife edge is due to stress cycles causing fatigue cracks. In the riveting process of machine countersunk, cracks mainly initiated around the rivet holes in the upper skin. In flush fasteners, the influence of rivet head in conjunction with the skin thickness on the stress distribution is still largely ...

  Edges, Knife, Knife edge

4-Bit Arithmetic And Logic Unit Design Using Structural ...

Very high scale integrated circuit Hardware Description Language. 1. Introduction The ALU, or the arithmetic and logic unit, is the section of the processor that is involved with executing operations of an arithmetic or logical nature. ... Design with VHDL” McGraw Hill, 2 nd

  With, Design, Circuit, Vhdl, Design with vhdl

Programmable DC Electronic Load for Testing on-Board ...

The Block diagram of programmable DC electronic load is as show in the Fig.1.The input voltage to device is between 6V-10V.Synchronous buck converter regulates the input voltage to constant voltage of 5V.The bias voltage for timer and Op-Amp are derived from the output of buck regulator .IC555 timer generates the required control signal, the ...

  Electronic, Load, Programmable, Programmable dc electronic load

Design and Performance Study of Shell and Tube Heat ...

Shell & tube type heat exchangers are built of tubes (round or rectangular in general) mounted in shells (cylindrical, rectangular or arbitrary shape). The differences lie mainly in the detailed features of construction and provisions for differential thermal expansion between the tubes and the shell. ...

  Tubes, Heat, Shell, Shell and tube heat

Performance Analysis of a Heat Recovery Steam …

The Heat Recovery steam Generator is one of the Critical components is the combined cycle (Gas Turbine cycle and Steam Power cycle) and is the most efficient energy conversation system in recent trends. Its function is to recover the waste heat present in the exhaust Gases of the Gas turbine ...

  Heat, Recovery, Steam, Heat recovery steam

A Resonant Converter Topology for Bidirectional DC DC ...

the existing bidirectional dc-dc converters fall into the generic circuit structure illustrated in figure 11.Based on the placement of the auxiliary energy storage, the bidirectional dc-dc converter can be categorized into buck and boost type. To realize the double sided

  Converter, Bidirectional, Bidirectional dc dc converters, Bidirectional dc, Bidirectional dc dc

Analysis, Design and Simulation of Bidirectional DC- DC ...

The bidirectional dc-dc flyback converters, a very simple structure, but the active switch suffer a high voltage stresses due to the leakage inductance of the transformer.

  Converter, Bidirectional, Bidirectional dc

Speed Control of Induction Motor using PWM Technique

for single phase AC induction motor. It has low cost, high efficiency drive capable of supplying a single phase induction motor with PWM modulated sinusoidal voltage. The circuit operation control by an 8051 family microcontroller[4].The device is aimed at substituting commonly used TRIAC phase angle control drives. ...

  Phases, Single, Motor, Induction, Single phase, Induction motors, Single phase induction motor

UTILITY PATENTAPPLICATION TRANSMITTAL

First Named Inventor: Title. ... Inventor’sOath or Declaration ... The information is required to obtain or retain a benefit by the public which is to file (and by the USPTO to process) an application. Confidentialityis governed by 35 U.S.C. 122 and 37 CFR 1.11 and 1.14. This collection is estimated to take 12 minutes to complete,

  First, Life, Transmittal, Inventors, To file

Prioritized Examination Question PE1: What is prioritized ...

granted. For guidance in filing a substitute statement, see Examples 2 and 4 in "Inventor’s Oath or Declaration Examples Featuring 'Best Practices' in Use of Inventor’s Oath or Declaration Forms." Question PE-Track One_8: Can I file an application under 35 U.S.C. 111(a) with a

  Life, Inventors

Methods of Intellectual Property Valuation

patent is a contract between society as a whole and an individual inventor. Under the terms of this social contract, the inventor is given the exclusive right to prevent others from making, using, and selling a patented invention for a fixed period of time in return for the inventor's disclosing the details of the invention to the public.

  Inventors

Week 6 - Project 3 - Assembly Drawings

ME 24-688 – Week 6 Project 3 – Assembly Drawings ME 24-688 – Introduction to CAD/CAE Tools Page 5 of 66 In the illustration, a new column is being added to the Bill of Materials editor. The left image shows the new column being dragged into position.