PDF4PRO ⚡AMP

Modern search engine that looking for books and documents around the web

Example: dental hygienist

AA-2000 ZOOM RigExpert

AA-2000 ZOOMRigExpert User s manualAntenna and cable analyzersFor latest manuals and software updates, please the AA-2000 ZOOMF irst time useMain menuMultifunctional keysConnecting to your antennaSWR chartChart ZOOMData screenFrequency and range entryReturn loss chartR,X chartSmith chartMemory operationSWR meter, SWR2 AirDisplay all parametersMultiSWR modeMultiband modeHOLD functionsFrequency generatorMy Bands ApplicationsAntennasCoaxial linesMeasurement of other elementsAnnexesAnnex 1: SpecificationsAnnex 2: PrecautionsAnnex 3: Tools menuTable of contentsAnnex 4: Setup menuAnnex 5: TDR mode Annex 6: CalibrationAnnex 7: Dummy loads DECLARATION OF CONFORMITY3435394142 RigExpert AA-2000 ZOOMT hank you for purchasing a RigExpert AA-2000 ZOOM Antenna and Cable Analyzer!

The analyzer is designed for measuring SWR (standing wave ratio), return loss, cable loss, as well as other parameters of cable and antenna systems in the range of 100 kHz to 2000 MHz. A built-in ZOOM capability makes graphical measurements especially effective. An integrated Time Domain Reflectometer

Fullscreen Download
Loading..

Tags:

  Waves, Ratios, Standing, Standing wave ratio

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Spam in document Broken preview Other abuse

Transcription of AA-2000 ZOOM RigExpert

Documents from same domain

ZOOM series RigExpert Antenna and cable analyzer

www.rigexpert.com

antenna, open circuit or short circuit. The following screen shot was taken in the real measurement. It shows 16 meters of 75 Ohm coaxial cable, antenna switching relay, and additional 37 meters of cable ending with an HF antenna. 11

  Meters, Antenna, Rigexpert, Rigexpert antenna

Help for MixW4

www.rigexpert.com

5. Transceiver - Audio, COM Ports settings, Control lines and Menu settings. For your MixW4 - transceiver connection to work correctly all required parts have to be configured correctly. A problem identified using MixW2 and MixW3 with a long USB cable was low voltage at Control interface units relying on power from the USB port.

  Line, Long

AA-230PRO - RigExpert

www.rigexpert.com

Pressing the 1 key will show a list of other commands. 4.2.2. SWR2Air mode RigExpert AA-230 and AA-230PRO present a new SWR2Air mode which is designed to help in adjusting antennas connected via long cables. This task usually involves two …

  Lists, Aa 230pro, 230pro

Related documents

160m/80m Broadband Antenna by K5GP

www.ctdxcc.org

The SWR plot for an 80 meter broadband dipole is shown below. For the antenna layout below, the center capacitor is 15 pF at element 3 between elements 2 and 4 and a 4:1 balun feeds the antenna between elements 1 and 2. The SWR is less than 1.7 to 1 across the entire 80 meter band. How do we get back the 160 meter resonance? By placing a series

  Series, Broadband, Antenna, 160m, 160m 80m broadband antenna by k5gp, K5gp

A Ten Meter Vertical Antenna for All License Classes

www.qsl.net

tuning the analyzer… I found a dip in SWR reading at 24 MHz. Note: This method works like the Grid Dip Oscillator of vacuum tube days of past. I found that if I reduced the value of C… then the frequency would go upwards. I connected the two variable capacitors in series to lower the C value. By adjusting the two caps while

  Series

Homebrew HF SWR/Power Meter - na0tc.org

www.na0tc.org

May 04, 2012 · •The lead inductance and C2 result in a series resonance that progressively deteriorates bridge balance as the frequency is raised Common Sensors 5/4/2012. ... SWR LED Radio Shack 276-0017 100K Forward 100K + 10K-3 1.21M 10 9 8 1 uF 1.0 uF Latch Relay1 +12 VDC 100 17 mA 1 16 +-Latch Relay1 13 8 6 9 4 11 0.1 uF To SWR Shutdown 5.1K Reset To +8 ...

  Series, Power, Meters, Homebrew, Homebrew hf swr power meter

Understanding SWR by Example - ARRL

www.arrl.org

as a 50 Ω resistor with a 100 nH inductor in series, or perhaps some capacitance to ground. In this situation, the SWR is not 1:1 because of the reactance. Even antennas that show a perfect 1:1 SWR in mid-band will typically have some larger SWR at the band edges, often due to the reactance of the antenna changing with frequency.

  Series

Antenna Impedance Matching – Simplified

abracon.com

Standing wave ratio (SWR) is a measure that defines how well the antenna impedance is matched to the connected Tx line impedance. A value less than 1.5 is desirable. A low flat SWR enables maximum power transfer from the ... When a series inductor is connected to the antenna, the combined impedance of the antenna ...

  Series, Waves, Ratios, Standing, Standing wave ratio

An Improved Double Extended Zepp - Antennas By N6LF

rudys.typepad.com

The series capacitors are 17 pF, and since he isn’t interested in CW, Dick adjusted the length for the lowest SWR at the high end of the band. The antenna could have been tuned somewhat lower in frequency and would then provide an SWR < 2:1 over the entire band, as indicated by the dashed line in Fig 8. This antenna provides wide bandwidth

  Series

My Loop Antenna - RCARC

www.rcarc.org

Antenna Dimension Counterpoise Band 2:1 SWR BW Rad. Res. ΩΩΩΩ Loss Res. Efficiency Base-loaded vertical (AB2EW) 6.67' tall Single wire, 25' long, on ground 40m 185 kHz 0.863 65.3 Ω 1.3% 30m 410 kHz 1.78 69.3 Ω 2.5% Base-loaded vertical (AB2EW) 15' tall Single wire, λ /4 long, elevated 5' 40m 248 kHz 4.68 32.1 Ω 12.7%

Ferrite and Common Mode Chokes - W4CAE

w4cae.com

get a decent SWR match. You can also sometimes see this effect when using an external (to your radio) SWR bridge. SWR should be the same along the entire feed line. If the external meter shows one SWR and your radio’s built in meter shows another then you might have a common mode current problem.

  Ferrites, Fired trane

Related search queries

160m/80m Broadband Antenna by K5GP, Series, Homebrew HF SWR/Power Meter, Standing wave ratio, Ferrite and