Material : Steel Scrap Grade

Inspection All material is to be suitable and acceptable to Steel Dynamics, Inc. based upon inspection as per TR-SOP-809. Loading/Unloading All grades must be capable of being loaded and unloaded by electromagnet. Seller’s indemnification includes indemnification for delivery under this Purchase Order by means of any frameless trailer.

  Material, Grade, Steel, Begin, Sparc, Steel scrap grade

AC Industrial Electric Motors Data Sheet

similar rated powers and mounting dimensions, i.e. shaft ... Three-phase motors available in both foot and flange mounting Wide voltage range on three-phase motors of 220-240V/250-280V if delta (Δ) connected or 380-420/440- ... torques of the motor vary approximately as the square of the voltage. The change in torque will also result in a ...

  Square, Motor, Dimensions, Flange

Steel Framing Inspection Guide

Web and flange sizes are expressed in 1/100ths of an inch and thickness is expressed in 1/1000ths of inch, or “mils.” Using the CFS universal designation system, the stud shown is a 6.00” x 1.62” stud shape of 50 KSI (kips per square inch) steel. CORROSION PROTECTION Steel studs are galvanized to protect the steel against

  Square, Flange

Flowseal High Performance Butterfly Valves

Separate part from gland flange, preventing uneven load distribution against packing. BODY ASME B16.34 design in either wafer or lug configuration. KEY Square key valve-to-operator connection provides an externally controlled failure point upon over-torquing. BLOW OUT PROOF SHAFT Solid shaft provides alignment and rigid support for disc.

  Square, Flange

Roof Drains Technical Data - jrsmith.com

flange will have a minimum 4" width with a 3/16" lip at drain body. If water - proof deck covering thickness is greater (or less) than 3/16”, lip dimension must be specified. Roughing dimensions of the body must be adjusted accordingly. Drain body should be set low enough to permit "dimpling" of area surrounding drain. Deck Covering Slab ...

  Dimensions, Flange, Jrsmith

INDEX Flow Rates for Ball Valves

Config. 1 Square Config. 2 Hexagonal A L SLV31F LOCKABLE BALL VALVE MALE - FEMALE STD. STAPLE Product Code Configuration Nominal Bore Pressure Rating bar Dimensions mm Dash Inch DN Working Burst L A AF D SLV31F-06-6RD 1 6 3/8” 10 500 1250 88 40 - SLV31F-08-6RD 1 8 1/2” 12 500 1250 112 40 - SLV31F-12-6RD 1 12 3/4” 20 500 1250 115 50 -

  Square, Dimensions

SECTION E - EMJ

tabulation, bearing piles are doubly-symmetric wide flange shapes whose inside flange surfaces are essentially parallel and whose flange and web have essentially the same thickness .) “C” shapes are channels produced in accordance with dimensional standards adopted in 1896 by the Association of American Steel Manufacturers for

  Section, Flange, Section e

PVM Variable Displacement Piston Pumps Vickers Product …

Flange Ports Outlet19mm25mm 25mm 25mm25mm 32mm* British Standard 05 Parallel Pipe – Inlet G 1-1/4 G 1-1/2 – – – – Tube Ports Outlet G 3/4 G 1 – – – – *SAE Code 62, high pressure series, or ISO 400 bar. Other flange ports are SAE Code 61, standard pressure series, or ISO 25-350 bar. 25 Thru-Drive Options

  Pumps, Piston, Variable, Displacement, Flange, Pvm variable displacement piston pumps

High Pressure Floating Ball Valve ASME Class 600, 900 & 1500

DESIGN STANDARDS Basic Design ASME B16.34 Pressure Rating—C.S. 3705 psi @ 100 deg F. Pressure Rating—S.S. 3600 psi @ 100 deg F. Pressure Test API 598 Ends ASME B16.11, B1.20.1 ISV Series BF2E - Standard Design Options 6 ASME Class 1500 ASME Class 1500 Floating Type Ball ValveFloating Type Ball Valve

PRODUCTS HANDBOOK Structural Steel

CONTINENTAL STEEL PTE LTD 100 Gul Circle, Singapore 629586. Phone: (65) 68620033 Facs: (65) 68616448/68624006. Website: www.consteel.com.sg PRODUCTS HANDBOOK Structural Steel

IPC-J-STD-001G: Requirements for Soldered Electrical and ...

IPC J-STD-001G Requirements for Soldered Electrical and Electronic Assemblies Developedby the J-STD-001Task Group(5-22a)of the Soldering Subcommittee(5-22) of the Assembly& JoiningCommittee(5-20)