Bitumastic 300M - Carboline

Bitumastic 300M PRODUCT DATA SHEET November 2021 300M Page 2 of 4 PERFORMANCE DATA (TYPICAL VALUES) ASTM B117 Salt FogTest Method Blasted steel 2 Coats 300MSystem Results No blistering, rusting or delamination. No measurable undercutting at scribe after 2000 hours ASTM D2794 Impact Blasted steel 2 Coats 300M Impact site diameter, 9.5, 9.5, 12.7 ...

  030m, Bitumastic 300m, Bitumastic

Carbozinc 859 - Carboline

Generic Type Organic Zinc Rich Epoxy Description Low VOC organic zinc epoxy steel primer with extremely fast cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. Carbozinc 859 has less than 360g/litre VOC (thinned) and is used extensively in virtually all industrial markets. Features

  Zinc, Carbozinc, Carbozinc 859

Carbozinc 11 HS - Carboline

These are nominal values. When used as a pre-construction primer thin up to 38 oz/gal using exempt Thinner 236 E. Topcoats Acrylics, Epoxies, Polyurethanes, High Heat Silicones, Silicates and others as recommended by your Carboline sales representative. Not required for certain exposures. A mist-coat/full-coat spray technique is often required to

  Itsm, Carbozinc, Carbozinc 11 hs

Carboguard 893 - Carboline

Brush Use a medium bristle brush. Roller Use a short-nap synthetic roller cover with phenolic core. APPLICATION CONDITIONS Condition Material Surface Ambient Humidity Minimum 4°C (40°F) 4°C (40°F) 4°C (40°F) 0% Maximum 32°C (90°F) 57°C (135°F) 43°C (110°F) 90% This product simply requires the substrate temperature to be above the ...

  Blister, Carboguard, Carboguard 893

Carbothane 134 HG - Carboline

24°C (75°F) 8 Hours 8 Hours 7 Days 32°C (90°F) 4 Hours 4 Hours 5 Days These times are based on a 50 micron dry film thickness. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure. *Maximum self-recoat times are indefinite.

  Carbothane 134 hg, Carbothane

Carbothane 134 - Carboline

NOTE: Substitute thinners, especially Lacquer Thinners, may contain alcohols which will inhibit the cure of Carbothane 134. Use of thinners other than those supplied or approved by StonCor Africa may adversely affect product performance and void product warranty, whether express or implied. Ratio 8:1 Pot Life

  Carbothane, Thinner, Carbothane 134

Thermaline 450 EP - Carboline

Surface profile should be a dense angular 1-3 mils and is best achieved through abrasive blasting. Remove all contaminants that would interfere with the performance of stainless steel for the intended service such as, but not limited to, imbedded iron or chlorides.

  Abrasive, Blasting, Abrasive blasting, 450 ep

Carboguard 890 - Carboline

January 2019 890 Page 2 of 4 SUBSTRATES & SURFACE PREPARATION General Surface must be clean and dry. Remove all dirt, dust, oil and all other contaminants. Steel Immersion: ISO 8501 Sa2½ Non-immersion: ISO 8501 Sa2½ 40 to 75µm ISO 8501 St2 or St3 are suitable cleaning methods for mild environments. Galvanized Steel

  Surfaces, Preparation, Steel, Mild, Surface preparation, Carboguard, Carboguard 890

SELECTION & SPECIFICATION DATA - Carboline

to these guidelines to achieve the desired results. Spray Application (General) The following spray equipment has been found suitable and is available from equipment manufacturers. Keep material under mild agitation during application. If spraying stops for more than 10 minutes, recirculate the material remaining in the spray line.

  Guidelines, Data, Specification, Material, Selection, Selection amp specification data

Carboguard 635 - Carboline

Potable Water Use: (0200) Beige, (0700) Grey and (0800) White Other Colours: Red and Black Gloss Satin Primer Self-priming Recommended Thickness 100 to 150 microns per coat Solid(s) Content By Volume: 65% ± 2% Theoretical Coverage Rates 25.6m²/litre at 25 microns 6.4m²/litre at 100 microns 4.3m²/litre at 150 microns Allow for loss in mixing ...

  Water, Carboguard, Carboguard 635

MEL-ROL - W. R. Meadows

MASTIC. (See Diagram C.) Drains and Protrusions … All protrusions should be sealed with two layers of membrane applied at least 6” (152.4 mm) in all directions. Seal all terminations with POINTING MASTIC. Around drains, apply two layers of MEL-ROL and put a bead of POINTING MASTIC between the membrane and clamping rings and at all

  Mastic

Technical Data Sheet Jotamastic 87 Aluminium

This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high build product. It is aluminium pigmented for improved barrier effect. Specially designed for areas where optimum surface preparation is not possible or desired. Provides long lasting protection in environments with high

  Mastic

Diagnostiquer les défauts de peinture et les éliminer.

> Décoloration du durcisseur peroxyde dans le mastic # 80 > Faible adhérence – mastic polyester # 15 > Faible adhérence sur le plastique # 19 > Faible opacité # 13 > Formation d’une marque aux bords saillants # 70 > Grains # 50 > Marbrures # 30 > Matage/brillant # 18 > Peau d’orange # 6 > Piqûres dans le polyester # 17

  Mastic

NIGP Commodity Codes (18th Edition) - Washington, D.C.

MASTIC, INSULATION 010-17-00. Aluminum Foil, etc. 010-17-15. INSULATION, ALUMINUM FOIL 010-17-28. INSULATION, FOIL BACK DUCT 010-30-00. Bands, Clips, and Wires (For Pipe Insulation) 010-30-15. BANDS, ALUMINUM FOR PIPE INSULATION 010-30-17. BANDS, STAINLESS STEEL FOR PIPE INSULATION 302/304

  Code, Commodity, Mastic, Nigp, Nigp commodity codes

PIPE AND EQUIPMENT - Owens Corning

foolproof. No need for staples or mastic • Meets Requirements for Mold and Fungi Resistance – VaporWick ® Pipe Insulation provides no sustenance for mold to propagate and meets the standard ASTM test for fungi resistance ASJ Description: FIBERGLAS SSL II® is a jacketed, pipe insulation molded of heavy density resin bonded inorganic glass ...

  Owens, Owens corning, Corning, Mastic

asbestos essentials

asbestos-containing mastic. Removal of floor tiles with an asbestos-paper backing will be notifiable non-licensed work (NNLW) – see sheet a0 Introduction to asbestos essentials. Preparing the work area Restrict access – minimise the number of people present. Close doors. Use tape and notices to warn others. Ensure adequate lighting. Equipment

  Mastic

LIRR Stations and Fare Zones Direct Fares Only Ticket Type ...

LIRR Stations and Fare Zones Direct Fares Only Ticket Type 1 3 4 7 9 10 12 14 Ticket Type Effective Date: April 21, 2019 Use of tickets is subject to all LIRR tariff rules and regulations. n/a = not available. Ten-Trip tickets are available to and from Zone 1 only.