V110 - Benjamin Moore & Co.

Jul 24, 2018 · V200 Line, V201, V230 Line, V231 Line, V220 Line, V300 Line, V520 Line, 540 Line, and Other Acrylics, Vinyl Acrylics & Alkyds V110 Waterborne DTM Metal Primer can be used as a barrier coat on top of older coatings prior to application of high performance coatings with “hotter” solvents, such as 2 component epoxies and urethanes.

  V300

ALIPHATIC ACRYLIC URETHANE GLOSS V500

Jul 23, 2018 · Aliphatic Acrylic Urethane is a multi-use, two-component urethane appropriate for use on both metal and masonry. This product provides excellent gloss and color retention when used on exterior surfaces exposed to sunlight and rain, and the highly cross-linked formula provides superior abrasion, chemical, and solvent resistance.

  Aliphatic

STIX - Benjamin Moore & Co.

Sep 09, 2019 · Surface wax should be removed with a commercial wax stripper. Grease residue should be removed with a grease and oil emulsifier. Remove all loose chipping, cracking and peeling from previously painted surfaces by hand scraping, sanding, wire brushing and/or by use of power tool cleaning methods such as electric sanders,

  Stripper

BRIGHTEN RESTORE REMOVE a b c Weathered …

48 48 REFINISH DECKS WITH ARBORCOAT® Treat the wood.Determine the wood you have to treat most appropriately. Check the weather. …

  Weathered

solid stain colors semi solid stain ... - Benjamin …

solid stain colors semi solid stain colors PLEASE NOTE: These representations of stained substrates can only approximate the actual color and opacity.

  Saint, Color, Solid, Semi, Solid stain colors semi solid, Solid stain colors semi solid stain colors

ADVANCE - Benjamin Moore & Co.

Oct 12, 2018 · Qualifies for LEED® v4 Credit Qualifies for CHPS low emitting credit (Collaborative for High Performance Schools) CDPH v1 Emission Certified Class A (0-25) over non-combustible surfaces when tested in accordance with ASTM E-84 Water Vapor Transmission: ASTM D1653 (method A): 2.55 perms

  Leeds, 174 v4

WATERBORNE AMINE EPOXY V440

Jul 25, 2018 · Benjamin Moore & Co., 101 Paragon Drive, Montvale, NJ 07645 Tel: 866-708-9180 Fax: 888-248-2143 www.benjaminmoore.com M72 …

POLYAMIDE EPOXY COATING GLOSS/SEMI-GLOSS V400

Aug 03, 2018 · Benjamin Moore & Co., 101 Paragon Drive, Montvale, NJ 07645 Tel: 866-708-9180 Fax: 888-248-2143 www.benjaminmoore.com M72 …

STIX - Benjamin Moore & Co.

Sep 09, 2019 · Technical Data White Vehicle Type Urethane Modified Acrylic Pigment Type Titanium Dioxide Volume Solids 40.0 ± 1.0% Coverage per Gallon at Recommended Film Thickness 300 – 400 Sq. Ft. Recommended Film Thickness –Wet 4.0 - 5.5 mils –Dry 1.6 - 2.2 mils Depending on surface texture and porosity. Be sure to estimate the

  Data, Technical, Technical data

ADVANCE - Benjamin Moore & Co.

Oct 12, 2018 · • Easy application • Easy clean up • Block resistant ... Cured plaster should be hard, have a slight sheen and maximum pH of 10; soft, porous or powdery plaster indicates improper cure. Never sand a plaster ... Refer to Safety Data Sheet for additional health and safety information.

  Sheet, Data, Safety, Safety data sheet, Easy, Sheen

SURFACE PREPARATION AND PAINTING STRUCTURAL STEEL …

an appropriate cleaning solution. All visible traces of contaminants are to be removed with final wiping performed with clean rags and clean solvent. A discussion of solvent cleaning methods and Specification SSPC-SP1-"Solvent Cleaning" are included in Figure 5-393.456 (12) thru (13). Surfaces of steel members for which blast cleaning is specified

  Quot, Cleaning, Painting, Solvents, Sspc, Solvent cleaning, Sspc sp1 quot solvent cleaning

Interzinc - AkzoNobel

Nov 23, 2016 · with SSPC-SP1 solvent cleaning. Abrasive Blast Cleaning Abrasive blast clean to a minimum of SSPC-SP6 or Sa2½ (ISO 8501-1:2007), (or SSPC-SP10 for optimum performance). If oxidation has occurred between blasting and application of Interzinc 22, the surface should be reblasted to the specified visual standard.

  Cleaning, Solvents, Sspc, Interzinc, Sspc sp1 solvent cleaning

Intertherm 50 - AkzoNobel

Oct 30, 2017 · Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning. Abrasive Blast Cleaning Abrasive blast clean to Sa2½ (ISO 8501-1:2007) or SSPC-SP6. If oxidation has occurred between blasting and application of Intertherm 50, the surface should be reblasted to the specified visual standard.

  Cleaning, Solvents, Sspc, Intertherm, Intertherm 50, Sspc sp1 solvent cleaning

Interthane 990 - AkzoNobel

May 25, 2016 · contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. SURFACE PREPARATIONS NEWBUILDING/MAJOR REFURBISHMENT Interthane 990 should always be applied over a recommended primer …

  Cleaning, Solvents, Sspc, Sspc sp1 solvent cleaning

Intergard 821 - AkzoNobel

Dec 04, 2015 · contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. SURFACE PREPARATIONS ANODE SHIELDS NEWBUILDING/MAJOR REFURBISHMENT Where necessary, remove weld spatter and smooth weld seams and sharp edges. Abrasive blast clean to Sa2½ (ISO 8501-1:2007). If oxidation has occurred between …

  Cleaning, Solvents, Sspc, Sspc sp1 solvent cleaning

SSPC-SP1 Solvent Cleaning

SSPC-SP1 Solvent Cleaning The method of solvent cleaning is intended to remove “all visible oil, grease, soil, drawing and cutting compounds, and all other soluble contaminants from steel surfaces.” The specification calls for the removal of dust before solvent cleaning by the use of a stiff bristle brush.

  Cleaning, Solvents, Sspc, Sspc sp1 solvent cleaning, Solvent cleaning