Experiment No: 1 Diode Characteristics
4) Observe the transfer characteristics by pressing the X-Y key of CRO 5) Plot the wave forms and the transfer characteristics. 6) Repeat the same procedure for the remaining 12 circuits as in Fig.2 to Fig. 13 7) For circuit with DC supply, choose appropriate value.
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Digital Electronics Circuits
sjce.ac.inDigital Electronics Circuits (EC37L) Lab in-charge: Dr. Shankraiah Course outcomes: After the completion of laboratory the student will be able to, 1. Simplify, design and implement Boolean expression/half and full adders using basic/universal gates. 2. Design and implement the various combinational circuits using MSI components. 3.
CONCRETE BLOCK MASONRY
sjce.ac.inThe width of cavity is constant with a suitable value between 40 to 100 mm & cavity is continuous in vertical direction expect at lintel on openings. The inner & outer walls are interconnected by means of “metal ties” or “bonding bricks”. The bottom of cavity wall should be well-ventilated by use of air bricks and ducts.
GEOTECHNICAL ENGINEERING LABORATORY
sjce.ac.inA) Determination of liquid limit (Casagrande method) B) Determination of plastic limit C) Determination of shrinkage factors 11 5. Determination of liquid limit of fine-grained soils by fall cone method 19 6. Determination of in situ dry density A) Core cutter method B) Sand Replacement method 21 7. Free swell tests 27 Engineering Property ...
Heat and Mass Transfer Laboratory Manual
sjce.ac.inConduction is a process of heat transfer through solids, liquids and gases. When the temperature gradient exists in a body, experience has shown that there is a transfer of heat from high temperature region to the low temperature region. The heat transfer rate per unit is
ELEMENTS OF CIVIL ENGINEERING
sjce.ac.inThey work to reduce environmental pollution, increase the world’s food supply, and make transportation faster & safer. Out of all branches of engineering, Civil Engineering is the one that is directly associated with the welfare of the society. …
LAB MANUAL for Computer Network
sjce.ac.in6. Click the General tab, click Internet Protocol (TCP/IP) in the connection uses the following items list, and then click Properties. 7. In the Internet Protocol (TCP/IP) Properties dialog box, click Obtain an IP address automatically (if it is not already selected), and then click OK.
Metrology and Measurement Laboratory Manual
sjce.ac.in2. Measurement of angle using Sine Center / Sine bar / bevel protractor 3. Measurement of alignment using Autocollimator / Roller set 4. Measurement of cutting tool forces using a) Lathe tool Dynamometer b) Drill tool Dynamometer. 5. Measurement of Screw threads Parameters using two wire or Three-wire methods. 6.
Manual, Laboratory, Measurement, Tool, Metrology, Metrology and measurement laboratory manual
Foundry and Forging Laboratory Manual
sjce.ac.in01 Foundry -Introduction 37-39 02 Core and Core Making 40-50 03 Solid Pattern 50-51 04 Hand Cutting 52-54 05 Self-Cored Pattern 55-56 06 Stepped Cone Pulley with Core Print 57-57 07 Split Pattern with Two Halves 58-58 08 Split Pattern with Two Halves 59-64
Manual, Introduction, Laboratory, Foundry, Forging, Foundry and forging laboratory manual
REMOTE SENSING AND GIS APPLICATIONS
sjce.ac.inHISTORY OF REMOTE SENSING The invention of photography in 1839 made remote sensing (eventually) possible. Remote sensing began in the 1860s as balloonists took pictures of the Earth's surface. Pigeon fleets were another form of remote sensing in the early years.
Machine Shop Manual
sjce.ac.inCutting of Gear Teeth using Milling Machine. COURSE OUTCOMES: ... milling machines, grinding machines, power saws, and presses (e.g., punch presses). ... cemented carbides, ceramics, diamond & cubic boron nitride (CBN). Types of Tool Materials: High Carbon steels High Speed Steels Cemented Carbides
Manual, Machine, Gear, Shops, Diamond, Boron, Cubic, Grinding, Nitride, Grinding machines, Machine shop manual, Cubic boron nitride
Related documents
II. Synchronous Generators
www.uotechnology.edu.iq• a dc generator is built on the same shaft as the ac generator’s rotor ... Example: The following data are taken from the open- and short-circuit characteristics of a 45-kVA, three-phase, Y-connected, 220-V (line-to-line), six-pole, 60-Hz synchronous machine. From …
Open, Generators, Circuit, Characteristics, Circuit characteristics, Dc generator
XR-2206 - SparkFun Electronics
www.sparkfun.comXR-2206 4 Rev. 1.04 DC ELECTRICAL CHARACTERISTICS Test Conditions: Test Circuit of Figure 2 Vcc = 12V, TA = 25°C, C = 0.01 F, R1 = 100k , R2 = 10k , R3 = 25k Unless Otherwise Specified. S 1 open for triangle, closed for sine wave. XR-2206P XR-2206CP/D
Open, Electronic, Circuit, Characteristics, Sparkfun, Sparkfun electronics
CIRCUITS LABORATORY EXPERIMENT 9 Operational Amplifiers
classes.engineering.wustl.edurelationship between the function generator output (which is the amplifier input) and the amplifier output. Compare your measurements to those predicted by Equation (9.3) above. 9.5.3 Inverting Amplifier with Multiple Inputs - Circuit 9.5.3. Assemble the circuit shown in Figure 9.7. Use the function generator to supply a 0.4 V peak-to-peak 1 kHz,
DC MACHINES AND TRANSFORMERS
www.iare.ac.inDC MOTORS AND TESTING: Principle of operation, back EMF, torque equation, condition for maximum power developed, types of DC motors, armature reaction and commutation, characteristics, methods of speed control, types of starters, numerical problems; Losses and
DS18S20 High-Precision 1-Wire Digital Thermometer
datasheets.maximintegrated.comPIN NAME FUNCTION TO-92 SO 1 5 GND Ground 2 4 DQ Data Input/Output. Open-drain 1-Wire interface pin. Also provides power to the device when used in parasite power mode (see the Powering the DS18S20 section.) 3 3 VDD Optional VDD.