ISOGARD™ GL Insulation

All Firestone polyisocyanurate foam insulations use EPA accepted blowing agents. Firestone ISOGARD GL incorporates a HCFC-free blowing agent that does not contribute to the depletion of the ozone layer (ODP-free). Method of Application: 1. Insulation shall be neatly fitted to all roof penetrations, projections and nailers. 2.

  Insulation

UltraPly™ TPO Walkway Pad - firestonebpco.com

Please contact Firestone Technical Services at 1-800-428-4511 for further information. This sheet is meant to highlight Firestone products and specifications and is subject to change without notice. Firestone takes responsibility for furnishing quality materials which meet published Firestone product specifications.

  Information, Technical

AG - UltraPly TPO Roofing Systems Application Guide

2. Consult container labels, Safety Data Sheets (SDS) and Technical Information Sheets (TIS) for specific safety instructions for all products used on the project. 3. Keep all adhesives, sealants and cleaning materials away from ALL ignition sources (i.e., flames, fire, sparks, etc.). Do not smoke while using these materials. 4.

  Guide, Applications, Sheet, Data, Safety, Safety data sheet, Application guide

ISOGARD™ HD Cover Board Coated Glass Facer High Density ...

Structural Concrete, 3000 psi (New & Existing) Please consult Membrane Design Guides on line at www.firestonebpco.comSteel, min. 22 ga to review specific information regarding fastener types appropriate for the type of deck and insulation in use. uge Lightweight Concrete* Plywood and OSB, min. ½" Gypsum, min. 2" NOT ACCEPTABLE

  Glass, Concrete

UltraPly™ TPO Roofing Systems

Nov 29, 2021 · Guide for Designers UltraPly TPO UltraPly TPO Platinum UltraPly TPO InvisiWeld™ ... the roof system and integration with the rest of the structure envelope. Firestone Building Products UltraPly TPO Roofing Systems - Guide for Designers ... compliance with specifications other than Firestone’s. 3. Hail coverage:

  Guide, Compliance, Envelope

UltraPly™ TPO Membrane

UltraPly™ TPO Membrane Firestone Building Products | Sales: (800) 428-4442 | Technical (800) 428-4511 | www.firestonebpco.com TIS 201 6/8/2021

  Technical

UNA-CLAD METAL - firestonebpco.com

STOCK PATTERN COLORS NON-STOCK PATTERN COLORS Available with minimum purchase amount and extended lead-time. Contact your local Sales Rep for more information.

Attachment Guide Supplemental Increased Wind Speed ...

Firestone Attachment Guide November 29, 2021 Attachment Guide & Supplemental Increased Wind Speed Warranty Attachment Guide November 2021 NOTE: The contents of this guide are considered accurate at time of posting. All information contained within should be validated for accuracy as it relates to

  Attachment

UltraPly™ Bonding Adhesive

6. Allow Bonding Adhesive to flash off until tacky. Touch down on the Bonding Adhesive surface with a clean, dry finger to be certain that the adhesive does not string. As you are touching the adhesive, pushing straight down to check for stringing, also push forward on the adhesive at an angle to ensure that the adhesive solvents have flashed

  Adhesive, Bonding, Ultraply, Bonding adhesive, Ultraply bonding adhesive

TIS 836 - TWIN JET

Spatter Application: Spatter Twin Jet at a rate of 60-70% coverage over the horizontal substrate and 75-85% at base tie-in locations, 2200 ft² (204 m²) to 2350 ft² (218 m²) per cannister set. • Do not apply Twin Jet Adhesive to the roof membrane. Keep lap areas of XR membrane clean and free of Twin Jet Adhesive overspray.

  Twin

Mineral Wool Insulation Comparison Charts

MINERAL WOOL PRODUCT COMPARISON Find out which JM mineral wool insulation products can stand in for our competitors’ products. Use this chart to find the right product. JM MINERAL WOOL INSULATION PRODUCT COMPARISON Easily compare the technical details and advantages of all our mineral wool insulation products.

  Product, Insulation, Insulation products

Extruded Polystyrene (XPS) Rigid Foam Insulation Product ...

Product Data Sheet FOAMULAR® Tapered Roofi ng Products Extruded Polystyrene (XPS) Rigid Foam Insulation Energy-Saving1, Moisture Resistant XPS Insulation THERMAPINK® 25 Tapered Insulation: ASTM C578 Type IV, 25 psi minimum FOAMULAR® 400 Tapered Insulation: ASTM C578 Type VI, 40 psi minimum FOAMULAR® 600 Tapered Insulation: …

  Product, Foam, Rigid, Polystyrene, Insulation, Extruded, Rigid foam insulation, Extruded polystyrene, Rigid foam insulation product

Extruded Polystyrene (XPS) Rigid Foam Insulation Product ...

Insulation. Product type • Minimum compressive strength of 25 psi • Wide selection of sizes and thicknesses • Available in straight, tongue and groove, or scored square edge • Compliant with building codes and standards Product Applications High-performance FOAMULAR ® 250 XPS insulation: • Retards the transmission of water vapor and ...

  Product, Polystyrene, Insulation, Extruded, Extruded polystyrene, Insulation products

Extruded Polystyrene (XPS) Rigid Foam Insulation Product ...

Product Applications High-performance FOAMULAR ® 150 XPS insulation: • Retards the transmission of water vapor and moisture in masonry walls • Provides continuous insulation over steel stud framing, in insulated concrete sandwich panel walls, or in masonry unit cavity walls, or when used with non-penetrating, surface mounted furring ...

  Product, Insulation, Insulation products

EnergyGuard Polyiso Insulation 20 & 25 PSI Data Sheet

Polyiso Insulation should be stored protected from the elements. Bundle wrap is not for use as waterproofing for boards. No more insulation should be installed than can be completely covered with roofing on the same day. • As unprotected polyisocyanurate will burn, fire safety precautions should be observed wherever insulation products are used.

  Insulation

DuPont Styrofoam Brand Square Edge XPS Foam Insulation

Styrofoam™ Brand Square Edge Insulation is classified as a Type IV product when tested in accordance with ASTM C578 and provides a long term insulating performance of R-5 per inch. Sustainable Solutions • Styrofoam™ Brand Square Edge Insulation is reusable in many applications. • Styrofoam™ Brand Square Edge Insulation uses BluEdge ...

  Product, Dupont, Insulation

JM TWO-PART URETHANE INSULATION ADHESIVE

Ensure all insulation boards are 4' x 4' (1.22 m x 1.22 m) or smaller. Ensure all surfaces are dry and free of any debris, dirt, oil and grease before using JM Two-Part UIA.

  Insulation